CHECK DRIVER SIDE JUNCTION BLOCK ASSEMBLY (INTEGRATION RELAY) (w/o Theft Deterrent System)
| *a | Vehicle Rear Side | *b | Vehicle Front Side |
Disconnect the 2H, 2L and 2D driver side junction block connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2H-4 (ALTB) - Body ground | LG - Body ground | Battery power supply | Always | 11 to 14 V |
| 2L-12 (BECU) - Body ground | L - Body ground | Battery power supply | Always | 11 to 14 V |
| 2D-9 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| 2D-18 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the 2H, 2L and 2D driver side junction block connectors.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| 2D-7 (LSWD) - Body ground* | L-R - Body ground | Front door unlock detection switch signal | Driver side door unlocked | Below 1 V |
| Driver side door locked | 11 to 14 V | |||
| 2O-27 (DCTY) - Body ground | R-B - Body ground | Driver side door courtesy light switch signal | Driver side door open | Below 1 V |
| Driver side door closed | 11 to 14 V | |||
| 2N-12 (ILE) - Body ground | P - Body ground | Ignition key cylinder light signal | Ignition key cylinder light on | Below 1 V |
| Ignition key cylinder light off | 11 to 14 V |
*: w/ Wireless Door Lock Control System
If the result is not as specified, the driver side junction block may have a malfunction.
CHECK THEFT WARNING ECU ASSEMBLY (w/ Theft Deterrent System)
Disconnect the G124 theft warning ECU connector.
Measure the resistance and voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G124-3 (+B1) - Body ground | L-Y - Body ground | Battery power supply | Always | 11 to 14 V |
| G124-12 (+B2) - Body ground | LG - Body ground | Battery power supply | Always | 11 to 14 V |
| G124-4 (IG) - Body ground | R-L - Body ground | Ignition power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V | |||
| G124-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the G124 theft warning ECU connector.
Measure the voltage according to the value(s) in the table below.
| Terminal No. (Symbol) | Wiring Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
| G124-2 (DMLP) - Body ground | P - Body ground | Interior lights signal | Interior lights on | Below 1 V |
| Interior lights off | 11 to 14 V | |||
| G124-7 (CTY) - Body ground | R-L - Body ground | All courtesy switch signals | Driver side, front passenger side, rear RH, rear LH or back door closed | 11 to 14 V |
| Driver side, front passenger side, rear RH, rear LH or back door open | Below 1 V |
If the result is not as specified, the theft warning ECU may have a malfunction.