Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1880E _58 Vehicle Interior _013240 METER / GAUGE / DISPLAY _0068630 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Entire Combination Meter does not Operate  


DESCRIPTION

This circuit is the power source circuit for the meter.

WIRING DIAGRAM

E224860
0.365,2.125 2.292,2.729 1.927,0.604 10 false from Ignition Switch 0.854,1.375 2.167,1.771 1.313,0.396 10 false from Battery 3.646,1.521 4.302,1.802 0.656,0.281 10 false DOME 2.792,1.521 3.708,2.052 0.917,0.531 10 false DCC 3.208,2.26 3.688,2.635 0.479,0.375 10 false MET 4.781,1.26 4.969,1.531 0.188,0.271 10 false 1 4.573,5.427 6.75,5.719 2.177,0.292 10 false Combination Meter Assembly 4.729,3.281 5.115,3.646 0.385,0.365 10 false 22 4.729,2 5.094,2.333 0.365,0.333 10 false 21 4.573,5.271 5.052,5.573 0.479,0.302 10 false G19 5.021,1.375 5.292,1.625 0.271,0.25 10 false B 5.021,2.115 5.479,2.396 0.458,0.281 10 false IG+ 5.021,3.385 5.604,3.771 0.583,0.385 10 false EP

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the G19 combination meter assembly connector.


E224604
0.156,1.396 0.573,1.646 0.417,0.25 0.813,1.438 0.813,0.635 0.813,0.635 0.708,0.635 true 0.813,1.615 1.021,1.917 1.021,1.917 1.115,1.917 true 0.906,1.563 0.906,0.583 0.906,0.583 1.083,0.583 true 0.073,0.052 0.396,0.323 0.323,0.271 10 false *a 0.542,0.531 0.76,0.729 0.219,0.198 10 false B 1.167,0.479 1.5,0.781 0.333,0.302 10 false EP 1.188,1.854 1.615,2.063 0.427,0.208 10 false IG+ 0.24,1.438 0.646,1.667 0.406,0.229 10 false G19
*a Front view of wire harness connector
(to Combination Meter Assembly)


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-22 (EP) - Body ground Always Below 1 Ω



c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G19-1 (B) - Body ground Always 11 to 14 V
G19-21 (IG+) - Body ground Ignition switch ON 11 to 14 V
G19-21 (IG+) - Body ground Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR