Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1880E _58 Vehicle Interior _013240 METER / GAUGE / DISPLAY _0068630 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Fuel Receiver Gauge Malfunction  


DESCRIPTION

The fuel sender gauge has a variable resistance mechanism. The resistance decreases when the fuel amount increases, and the resistance increases when the fuel amount decreases. The fuel receiver gauge changes based on the resistance of the fuel sender gauge.


NOTICE:

When the combination meter is removed or replaced, its connector is disconnected or fuel is added, the fuel receiver gauge display will return to normal within a maximum of 16 minutes after the ignition switch is turned to ON or when vehicle speed is input.


WIRING DIAGRAM

E271742
1.823,1.25 4,1.521 2.177,0.271 10 false Fuel Sender Gauge Assembly 1.396,0.771 1.552,0.969 0.156,0.198 10 false 3 1.656,0.771 1.948,0.958 0.292,0.188 10 false FE 2.135,0.771 2.292,0.969 0.156,0.198 10 false 1 3.188,0.771 3.344,0.969 0.156,0.198 10 false 2 3.542,0.771 3.833,0.958 0.292,0.188 10 false FS 3.917,0.771 4.073,0.969 0.156,0.198 10 false 2 5.521,0.771 5.677,0.969 0.156,0.198 10 false 3 5.802,0.875 5.958,1.073 0.156,0.198 10 false L 5.802,2.5 6.198,2.719 0.396,0.219 10 false ES 5.521,2.396 5.677,2.594 0.156,0.198 10 false 2 1.563,1.688 1.854,1.875 0.292,0.188 10 false L4 1.573,1.875 4.979,2.208 3.406,0.333 10 false Fuel Suction with Pump and Gauge Tube Assembly 5.188,2.99 5.76,3.146 0.573,0.156 10 false G19 5.198,3.167 7.073,3.417 1.875,0.25 10 false Combination Meter Assembly

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY)
a.

Disconnect the G19 combination meter assembly connector.


b.

Disconnect the L4 fuel suction with pump and gauge tube assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G19-2 (ES) - L4-3 (FE) Always Below 1 Ω
G19-3 (L) - L4-2 (FS) Always Below 1 Ω
G19-2 (ES) - G19-3 (L) Always 10 kΩ or higher
G19-2 (ES) - Body ground Always 10 kΩ or higher
G19-3 (L) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
a.

Remove the fuel suction with pump and gauge tube assembly.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.
E226597
0.104,0.135 0.417,0.406 0.313,0.271 10 false *a 0.625,0.323 0.969,0.708 0.344,0.385 10 false *c 0.104,1.948 0.396,2.26 0.292,0.313 10 false *b 0.542,2.177 0.958,2.542 0.417,0.365 10 false *d
*a Upper Side
*b Lower Side
(to Fuel Sender Gauge Assembly)
*c Connector A
*d Connector B


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-3 - B-1 Always Below 1 Ω
A-2 - A-3 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

3.INSPECT FUEL SENDER GAGE ASSEMBLY

NG

REPLACE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

3.INSPECT FUEL SENDER GAGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>2TR-FE FUEL>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.
A246391
1.448,2.292 0.677,2.292 true 1.354,3.938 0.677,3.938 true 2.115,1 2.24,1.146 0.125,0.146 10 false 3 1.677,1 1.802,1.146 0.125,0.146 10 false 2 1.219,1 1.344,1.146 0.125,0.146 10 false 1 0.469,3.833 0.771,4.135 0.302,0.302 10 false *b 0.458,2.177 0.792,2.458 0.333,0.281 10 false *a
*a Float Position F (Upper)
*b Float Position E (Lower)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 Float position F (upper) 3 to 5 Ω
Float position E (lower) 109 to 111 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FUEL SENDER GAGE ASSEMBLY