Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM
RM1880E _58 Vehicle Interior _013240 METER / GAUGE / DISPLAY _0068630 METER / GAUGE SYSTEM J

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  Accessory Meter does not Illuminate  


DESCRIPTION

This circuit provides power to the accessory meter assembly.

WIRING DIAGRAM

E224858
0.531,0.521 2.083,0.969 1.552,0.448 10 false from Ignition Switch 0.552,1.292 2.229,1.74 1.677,0.448 10 false from Ignition Switch 1.021,2.031 2.188,2.542 1.167,0.51 10 false from Battery 3.49,2.188 4.083,2.531 0.594,0.344 10 false DOME 2.656,2.188 3.396,2.552 0.74,0.365 10 false DCC 3.073,1.438 3.771,1.719 0.698,0.281 10 false ACC 4.729,1.313 5.365,1.792 0.635,0.479 10 false ACC 2.708,0.677 3.948,1.021 1.24,0.344 10 false ECU-IG&GAUGE 4.708,2.021 5.104,2.323 0.396,0.302 10 false +B 4.708,0.521 5.135,0.885 0.427,0.365 10 false IG 4.708,2.906 5.313,3.188 0.604,0.281 10 false SGND 4.708,3.656 5.427,3.958 0.719,0.302 10 false GND1 4.406,1.896 4.854,2.219 0.448,0.323 10 false 14 4.406,0.406 4.76,0.74 0.354,0.333 10 false 12 4.406,1.156 4.771,1.5 0.365,0.344 10 false 13 4.406,2.781 4.938,3.177 0.531,0.396 10 false 10 4.479,3.531 4.823,3.833 0.344,0.302 10 false 1 4.479,4.417 6.448,4.688 1.969,0.271 10 false Accessory Meter Assembly 4.469,4.219 5.125,4.521 0.656,0.302 10 false G112

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (ACCESSORY METER ASSEMBLY CIRCUIT)
a.

Disconnect the G112 accessory meter assembly connector.


E224859
1.49,0.729 1.906,0.979 0.417,0.25 1.021,1.792 0.604,1.792 true 2.781,2.104 2.365,2.104 true 1.156,2.677 1.5,2.198 true 1.896,2.688 1.896,2.188 true 2.542,2.656 2.135,2.188 true 1.542,0.771 2.021,1.01 0.479,0.24 10 false G112 0.938,2.76 1.469,3.031 0.531,0.271 10 false SGND 0.167,1.719 0.865,2.052 0.698,0.333 10 false GND1 2.469,2.729 2.938,2.958 0.469,0.229 10 false ACC 2.865,2.021 3.302,2.396 0.438,0.375 10 false +B 1.865,2.75 2.208,3.083 0.344,0.333 10 false IG 0.135,0.302 0.521,0.594 0.385,0.292 10 false *a
*a Front view of wire harness connector
(to Accessory Meter Assembly)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G112-12 (IG) - Body ground Ignition switch ON 11 to 14 V
G112-13 (ACC) - Body ground Ignition switch ACC 11 to 14 V
G112-14 (+B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G112-1 (GND1) - Body ground Always Below 1 Ω
G112-10 (SGND) - Body ground Always Below 1 Ω
G112-12 (IG) - Body ground Always 10 kΩ or higher
G112-13 (ACC) - Body ground Always 10 kΩ or higher
G112-14 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ACCESSORY METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR