Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2011.07–2013.08
RM1880E _58 Vehicle Interior _013242 SUPPLEMENTAL RESTRAINT SYSTEMS _0068641 AIRBAG SYSTEM D

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  DIAGNOSIS SYSTEM  


SYMPTOM SIMULATION


C206435
0.618,0.0 1.6,0.205 0.983,0.205 10 Vibrate Slightly 0.281,2.604 1.264,2.809 0.983,0.205 10 Shake Slightly 1.115,4.114 2.097,4.319 0.983,0.205 10 Vibrate Slightly

HINT:

The most difficult case in troubleshooting is when no problem symptoms occur. In such a case, a thorough problem analysis must be carried out. A simulation of the same or similar conditions and environment in which the problem occurred in the customer's vehicle should be carried out. No matter how much skill or experience a technician has, troubleshooting without confirming the problem symptoms will lead to important repairs being overlooked and mistakes or delays.


a.

Vibration method: When vibration seems to be the major cause.

HINT:

Perform the simulation method only during the primary check period (for approximately 6 seconds after the ignition switch is turned to ON).


i.

Slightly vibrate the part of the sensor considered to be the cause of the problem with your fingers and check whether the malfunction occurs.

NOTICE:

Shaking the relays too strongly may result in open relays.



ii.

Slightly shake the connector vertically and horizontally.


iii.

Slightly shake the wire harness vertically and horizontally.

HINT:

The connector joint and fulcrum of the vibration are the major areas to be checked thoroughly.





FUNCTION OF SRS WARNING LIGHT


a.

Primary check.

i.

Turn the ignition switch off. Wait for at least 2 seconds, and then turn the ignition switch to ON. The SRS warning light comes on for approximately 6 seconds and diagnosis of the airbag system is performed.

HINT:

If trouble is detected during the primary check, the SRS warning light remains on even after the primary check period (of approximately 6 seconds) has elapsed.




b.

Constant check.

i.

After the primary check, the center airbag sensor constantly monitors the airbag system for trouble.

HINT:

If trouble is detected during the constant check, the center airbag sensor functions as follows:

·

The SRS warning light comes on.

·

The SRS warning light goes off, and then comes on. This blinking pattern indicates a source voltage drop. The SRS warning light goes off 10 seconds after the source voltage returns to normal.





c.

Review.

i.

When the airbag system is normal:

The SRS warning light comes on only during the primary check period (for approximately 6 seconds after the ignition switch is turned to ON).


ii.

When the airbag system has trouble:

·

The SRS warning light remains on even after the primary check period has elapsed.

·

The SRS warning light goes off after the primary check, but comes on again during the constant check.

·

The SRS warning light does not come on when turning the ignition switch from off to ON.


HINT:

The center airbag sensor functions to keep the SRS warning light on if the airbag has been deployed.





CHECK SRS WARNING LIGHT


a.

Turn the ignition switch to ON and check that the SRS warning light comes on for approximately 6 seconds (primary check).


b.

Check that the SRS warning light goes off approximately 6 seconds after the ignition switch is turned to ON (constant check).

HINT:

When any of the following symptoms occur, refer to the "Problem Symptoms Table" (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PROBLEM SYMPTOMS TABLE).

·

The SRS warning light comes on occasionally after the primary check period has elapsed.

·

The SRS warning light comes on, but a DTC is not output.

·

The ignition switch is turned from off to ON, but the SRS warning light does not come on.





FUNCTION OF SRS CONNECTORS


a.

SRS connectors are located as shown in the illustration.

C247556
0.262,0.483 1.08,0.851 0.817,0.368 10 Front Airbag Sensor RH 0.296,4.616 1.169,4.984 0.873,0.368 10 Front Airbag Sensor LH 0.216,5.466 1.969,5.632 1.753,0.166 10 *1: for Driver Side 1.589,5.466 3.342,5.632 1.753,0.166 10 *2: for Passenger Side 0.286,2.434 1.241,2.975 0.955,0.541 10 Center Airbag Sensor 3.268,2.81 4.283,3.164 1.014,0.354 10 Spiral Cable Sub-assembly 4.948,0.6 6.445,0.988 1.496,0.388 10 Combination Meter (SRS Warning Light) 4.757,1.846 7.036,2.216 2.278,0.37 10 Instrument Panel Passenger Airbag (Front Passenger Side Squib) 4.757,2.75 5.952,3.117 1.194,0.368 10 Steering Pad (Driver Side Squib) 1.336,1.366 1.475,1.57 0.14,0.204 10 1 1.451,1.464 1.602,1.668 0.151,0.205 10 2 1.37,4.439 1.52,4.645 0.151,0.206 10 3 1.485,4.544 1.67,4.75 0.184,0.206 10 4 1.817,2.232 1.99,2.437 0.173,0.205 10 5 2.01,2.235 2.183,2.44 0.173,0.205 10 6 3.531,1.961 3.704,2.166 0.173,0.205 10 11 3.724,1.964 3.897,2.169 0.173,0.205 10 12 3.002,2.73 3.163,2.946 0.162,0.215 10 7 3.127,2.607 3.311,2.811 0.184,0.205 10 8 4.475,2.703 4.614,2.907 0.14,0.205 10 9 4.53,2.602 4.769,2.806 0.24,0.205 10 10 1.347,0.3 1.498,0.504 0.151,0.205 10 3 1.457,0.404 1.641,0.609 0.184,0.205 10 4 4.475,1.811 4.736,2.016 0.262,0.205 10 9 4.54,1.691 4.835,1.896 0.295,0.205 10 10 4.403,0.646 4.698,0.855 0.295,0.209 10 13 4.519,0.54 4.769,0.745 0.251,0.205 10 14 1.352,2.357 1.603,2.562 0.251,0.204 10 1 1.468,2.488 1.73,2.692 0.262,0.204 10 2 4.475,3.636 4.725,3.84 0.251,0.204 10 9 4.528,3.505 4.768,3.709 0.24,0.204 10 10 1.346,3.362 1.596,3.566 0.251,0.204 10 1 1.466,3.5 1.727,3.704 0.262,0.204 10 2 4.475,4.558 4.725,4.762 0.251,0.204 10 9 4.518,4.42 4.758,4.624 0.24,0.204 10 10 4.761,3.657 6.827,4.198 2.066,0.541 10 Front Seat Outer Belt Assembly (Front Pretensioner Squib)*1 4.761,4.591 6.827,5.132 2.066,0.541 10 Front Seat Outer Belt Assembly (Front Pretensioner Squib)*2

Connector Type Application
Terminal Twin-Lock Mechanism Connectors 2, 4, 5, 6, 7, 9, 11, 12
Half Connection Prevention Mechanism Connectors 4, 6, 7, 11
Activation Prevention Mechanism Connectors 2, 8, 12
Connector Lock Mechanism (1) Connectors 9
Connector Position Assurance Mechanism Connector 4
Connector Lock Mechanism (2) Connector 2
Improper Connection Prevention Lock Mechanism Connector 1


b.

Terminal twin-lock mechanism

C234183
1.802,0.896 2.281,0.156 2.281,0.156 1.854,0.156 true 5.802,0.625 5.74,0.167 5.74,0.167 5.583,0.167 false 0.521,0.073 2.01,0.5 1.49,0.427 10 false Lance (Primary Lock) 1.26,1.458 2.25,1.75 0.99,0.292 10 false Primary Lock 4,0.083 5.771,0.51 1.771,0.427 10 false Spacer (Secondary Lock) 4.938,1.448 6.104,1.76 1.167,0.313 10 false Secondary Lock

i.

This mechanism is designed to increase the ability of the terminal to remain connected and prevent it from accidentally being disconnected.


ii.

The connector has a two-piece construction consisting of the housing and spacer to securely lock the terminal using both the lance (primary lock) and spacer (secondary lock).



c.

Half connection prevention mechanism

C147461
1.542,1.406 1.542,1.219 1.542,1.219 1.302,1.219 false 1.833,1.375 1.833,0.927 1.833,0.927 1.677,0.927 false 2.375,1.302 2.375,0.646 2.375,0.646 2.188,0.646 true 2.979,1.198 2.979,0.688 2.979,0.688 3.135,0.688 true 3.25,1.313 3.25,0.917 3.25,0.917 3.49,0.917 true 6.104,1.146 6.104,0.729 6.104,0.729 5.885,0.729 true 1.365,0.552 2.208,0.76 0.844,0.208 10 false Locking Arm 1.146,0.823 1.688,0.99 0.542,0.167 10 false Stopper 0.49,1.135 1.323,1.313 0.833,0.177 10 false Locking Part 3.177,0.625 3.615,0.813 0.438,0.188 10 false Slider 3.573,0.833 4.042,1.021 0.469,0.188 10 false Spring 5.302,0.646 5.885,0.833 0.583,0.188 10 false Stopper 4.708,1.906 6.042,2.094 1.333,0.188 10 false Rebound by Slider

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

If the connector is not completely connected, the connector is disconnected by the force of the spring so that no continuity exists.



d.

Activation prevention mechanism

C231798
1.906,0.979 1.521,0.823 false 2.688,1.292 3.198,0.969 3.198,0.969 2.854,1.375 true 2.99,1.542 3.344,1.292 true 2.063,1.583 1.365,1.708 true 1.865,1.365 1.427,1.365 true 1.865,3.229 2.208,3.729 true 2.208,3.74 2.573,3.208 true 2.042,3.219 2.208,3.74 true 2.219,3.229 2.208,3.74 true 2.385,3.229 2.208,3.74 true 5.813,3.427 6.052,3.844 true 6.052,3.844 6.198,3.438 true 5.958,3.438 6.052,3.844 true 6.063,3.438 6.052,3.844 true 4.667,1.823 5.188,1.302 true 2.042,0.344 3.073,0.729 1.031,0.385 10 false When open 0.646,0.698 1.667,1.115 1.021,0.417 10 false Male Housing 3.25,0.833 4.479,1.156 1.229,0.323 10 false Female Terminal 0.521,1.281 1.521,1.635 1,0.354 10 false Male Terminal 3.396,1.177 4.583,1.542 1.188,0.365 10 false Female Housing 0.521,1.635 1.344,2.188 0.823,0.552 10 false Short Spring Plate 5.313,0.344 6.323,0.688 1.01,0.344 10 false When shorted 2.896,1.781 4.667,2.417 1.771,0.635 10 false Short spring plate contacting the male terminal 1.125,2.458 3.406,3.146 2.281,0.688 10 false Front view of wire harness connector: (to Center Airbag Sensor Assembly) 1.833,3.781 2.813,4.094 0.979,0.313 10 false Short Spring 4.74,2 7.031,2.469 2.292,0.469 10 false Front view of wire harness connector: (to Spiral Cable) 1.729,4.042 3.031,4.635 1.302,0.594 10 false (to Instrument Panel Wire Harness) 5.635,3.896 6.542,4.292 0.906,0.396 10 false Short Spring

i.

The activation prevention mechanism is designed to create a short circuit automatically between the positive (+) and negative (-) terminals of an airbag power source connector when disconnected.


ii.

The short spring plate contained in the connector creates a closed circuit on the airbag side (no potential difference can occur between both terminals), preventing accidental airbag deployment when servicing.



e.

Connector lock mechanism (1)

C147462
2.521,0.344 2.521,0.177 2.521,0.177 2.146,0.177 false 2.635,0.76 2.156,0.76 true 2.448,1.24 2.125,1.24 false 4.927,0.885 5.24,0.885 false 0.615,0.083 2.104,0.313 1.49,0.229 10 false Lock the locking button 1.76,0.677 2.135,0.844 0.375,0.167 10 false Claw 1.625,1.146 2.115,1.313 0.49,0.167 10 false Groove 5.292,0.719 7,1.052 1.708,0.333 10 false Claw on the locking button is locked in the groove

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Locking the connector locking button engages the locking button claw in the groove of the other connector to connect the connector securely.



f.

Connector Position Assurance (CPA) mechanism

C161464
0.833,1.125 0.833,0.271 0.833,0.271 0.979,0.271 true 0.938,1.219 1.146,0.594 1.146,0.594 1.281,0.594 true 0.51,1.813 0.823,2.333 0.823,2.333 0.979,2.333 true 5.646,1.135 5.51,0.813 5.51,0.813 5.375,0.813 true 1.052,0.188 2.323,0.5 1.271,0.313 10 false Female Connector 1.344,0.5 2.281,0.781 0.938,0.281 10 false Locking Part 1.031,2.25 2.25,2.573 1.219,0.323 10 false Male Connector 2.958,0.323 4.635,0.708 1.677,0.385 10 false Primary Lock Completed 5.073,0.313 6.844,0.635 1.771,0.323 10 false Secondary Lock Completed 4.823,0.719 5.531,1.031 0.708,0.313 10 false Retainer

i.

This mechanism is designed to detect when the connector is connected only halfway.


ii.

The CPA and female connector slide to the male connector side at the same time and the primary lock is completed when the female connector is engaged with the male connector. From this point, only the CPA slides to the male connector side. The secondary lock is completed when the CPA retainer is engaged with the female connector. When the CPA and female connector ends are aligned, the connectors are completely engaged.



g.

Connector lock mechanism (2)

C231508
1.958,3.073 2.51,3.531 2.51,3.531 2.677,3.531 true 4.375,1.5 4.625,1.792 4.625,1.792 4.781,1.792 false 5.646,2.76 5.51,2.615 5.51,2.615 5.385,2.615 false 5.51,3.25 5.052,3.542 5.052,3.542 4.854,3.542 true 4.115,2.771 3.938,3.156 3.938,3.156 3.802,3.156 false 1.281,1.448 1.104,1.927 1.104,1.927 0.958,1.927 true 5.76,2.625 5.802,2.354 5.802,2.354 5.906,2.354 false 0.542,1.833 1.052,2.115 0.51,0.281 10 false Lance 4.854,1.708 5.438,2.01 0.583,0.302 10 false Holder 2.74,3.448 3.5,3.74 0.76,0.292 10 false Retainer 4.292,3.448 5.01,3.75 0.719,0.302 10 false Retainer 3.25,3.052 3.917,3.333 0.667,0.281 10 false Retainer 4.958,2.521 5.469,2.781 0.51,0.26 10 false Holder 5.948,2.271 6.365,2.479 0.417,0.208 10 false Claw

i.

This mechanism is designed to prevent the connector from accidentally being disconnected.


ii.

Sliding the connector all the way into the holder and locking the lance completes the primary lock.


iii.

Engaging the retainer with the holder as shown in the illustration completes the secondary lock, preventing the connector from accidentally being disconnected.



h.

Improper connection prevention lock mechanism

C231509
1.167,2.656 1.396,2.656 1.396,2.656 1.396,1.542 true 5.052,1.01 4.125,1.01 true 5.021,0.677 5.271,0.146 5.271,0.146 5.552,0.146 false 1.49,1.083 1.49,0.833 1.49,0.833 1.708,0.833 false 4.156,3.26 4.615,3.26 true 3.708,0.073 4.333,0.292 0.625,0.219 10 false Top View 0.427,2.573 1.208,2.75 0.781,0.177 10 false Unlock Rib 3.427,0.833 4.094,1.229 0.667,0.396 10 false Temporary Hold Lock 3.792,3.167 4.208,3.344 0.417,0.177 10 false Lever 5.646,0.083 6.417,0.302 0.771,0.219 10 false Unlock Rib 1.76,0.75 1.979,0.958 0.219,0.208 10 false A

i.

This mechanism is designed to prevent the connector from being connected only halfway.


ii.

When the holder is connected to the airbag sensor assembly, the unlock rib unlocks the temporary hold lock, allowing the lever to be pushed in by rotating around the A axis.


iii.

Locking the lever to the holder locks the holder securely.




ACTIVATION PREVENTION MECHANISM


a.

Function of activation prevention mechanism

i.

An activation prevention mechanism is built into the connector (on the center airbag sensor assembly side) of the airbag system squib circuit to prevent accidental airbag activation.


ii.

This mechanism closes the circuit when the connector is disconnected by bringing the short spring into contact with the terminals and insulating the circuit from external power sources to prevent accidental airbag activation.



b.

Releasing of activation prevention mechanism

i.

To release the activation prevention mechanism, insert a piece of paper with the same thickness as the male terminal (approximately 0.5 mm [0.0197 in.]) between the terminals and short spring to break the connection.


ii.

Refer to the following illustrations concerning connectors utilizing the activation prevention mechanism and its release method.

CAUTION:

Never release the activation prevention mechanism on the squib connector even when inspecting with the squib disconnected.


NOTICE:
·

Do not release the activation prevention mechanism unless specially directed by the troubleshooting procedure.

·

To prevent the terminal and short spring from being damaged, always use a piece of paper with the same thickness as the male terminal.



C215596
2.188,1.083 2.469,1.292 0.281,0.208 1.958,4.49 2.24,4.698 0.281,0.208 1.635,6.729 1.917,6.938 0.281,0.208 3.552,1.219 3.677,2.052 3.677,2.052 3.865,1.219 true 2.396,3.167 2.875,3.865 2.875,3.865 3.01,3.865 true 5.406,3.156 5.875,3.646 5.875,3.646 5.99,3.646 true 3.198,2.688 3.021,2.969 false 2.458,5.875 2.365,6.292 2.365,6.292 2.302,5.875 true 3.573,5.615 3.698,6.313 true 4.427,5.719 4.531,5.323 false 6.323,5.719 6.49,5.354 false 5.531,5.615 5.625,6.302 true 6.031,2.688 5.844,2.969 false 1.281,7.833 1.271,8.052 1.271,8.052 1.104,7.833 true 3.354,7.74 3.469,8.208 true 3.948,7.677 4.042,7.292 false 6.396,7.677 6.563,7.313 false 5.771,7.74 5.448,8.177 true 2.573,0.281 4.906,0.708 2.333,0.427 10 false Center Airbag Sensor Connector 2.292,1.104 2.552,1.427 0.26,0.323 10 false 2 2.063,4.521 2.313,4.771 0.25,0.25 10 false 8 5.292,6.333 6.344,6.646 1.052,0.313 10 false Short Spring 3.438,6.333 4.458,6.646 1.021,0.313 10 false Short Spring 2.052,6.333 3.063,6.656 1.01,0.323 10 false Short Spring 3.083,3.781 4.115,4.135 1.031,0.354 10 false Short Spring 3.354,2.104 4.354,2.521 1,0.417 10 false Short Spring 1.406,2.375 2.604,2.708 1.198,0.333 10 false Before Release 6.052,3.563 7.104,3.875 1.052,0.313 10 false Short Spring 3.25,2.563 3.927,2.885 0.677,0.323 10 false Paper 4.313,2.406 5.375,2.729 1.063,0.323 10 false After Release 1.271,4.5 2.125,4.833 0.854,0.333 10 false Connector 3.438,4.771 4.635,5.115 1.198,0.344 10 false Before Release 5.427,4.771 6.604,5.094 1.177,0.323 10 false After Release 4.594,5.198 5.177,5.49 0.583,0.292 10 false Paper 6.542,5.219 7.063,5.49 0.521,0.271 10 false Paper 6.094,2.552 6.667,2.823 0.573,0.271 10 false Paper 1.698,6.76 1.917,6.969 0.219,0.208 10 false 12 5.031,8.208 6.083,8.531 1.052,0.323 10 false Short Spring 3.198,8.229 4.24,8.542 1.042,0.313 10 false Short Spring 0.938,8.094 2.01,8.458 1.073,0.365 10 false Short Spring 0.938,6.74 1.615,6.969 0.677,0.229 10 false Connector 2.708,6.927 3.927,7.302 1.219,0.375 10 false Before Release 5.292,6.896 6.302,7.24 1.01,0.344 10 false After Release 4.073,7.156 4.625,7.417 0.552,0.26 10 false Paper 6.594,7.177 7.104,7.521 0.51,0.344 10 false Paper