Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for Captain Seat Type)
RM1880E _58 Vehicle Interior _013243 SEAT _0068643 REAR NO. 1 SEAT ASSEMBLY(for Captain Seat Type) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for Captain Seat Type)  DISASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 1.REMOVE REAR SEAT HEADREST ASSEMBLY

a.

Remove the rear seat headrest assembly.


Hide 2.REMOVE REAR SEAT INNER CUSHION SHIELD RH

a.
B155358
2.625,1.333 2.927,1.615 0.302,0.281 10 false (1) 2.01,1.104 2.281,1.417 0.271,0.313 10 false (2) 1.823,1.448 2.146,1.771 0.323,0.323 10 false (3)

Remove the 2 screws.


b.

Detach the rear part of the rear seat inner cushion shield RH in the order shown in the illustration, and then detach the claw and remove the rear seat inner cushion shield RH.


Hide 4.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH

a.
B276711
2.708,0.365 2.063,0.365 true 2.781,0.281 3.073,0.594 0.292,0.313 10 false *1
*1 Protective Tape


Raise the reclining adjuster release handle RH to reveal the claw. Using a screwdriver, detach the claw and remove the reclining adjuster release handle RH.

HINT:

Tape the screwdriver tip before use.



Hide 5.REMOVE REAR SEAT CUSHION SHIELD RH

a.
B155360
0.573,1.313 0.896,1.615 0.323,0.302 10 false (1) 1.479,1.26 1.844,1.604 0.365,0.344 10 false (2)

Remove the 2 screws.


b.

Detach the rear part of the rear seat cushion shield RH in the order shown in the illustration, and then detach the claw and remove the rear seat cushion shield RH.


Hide 6.REMOVE REAR SEAT ARMREST ASSEMBLY RH

a.
B278700
2.615,0.448 2.458,0.448 2.458,0.448 2.281,0.688 true 2.677,0.365 2.833,0.51 0.156,0.146 10 false *1
*1 Fastener


Detach the fastener and open the rear seat armrest cover.


b.
B278701
0.771,1.51 0.844,1.51 0.844,1.51 0.938,1.708 false 1.427,2.063 1.354,2.063 1.354,2.063 1.25,1.865 false 0.604,1.427 0.875,1.677 0.271,0.25 10 false *1 1.448,1.99 1.719,2.177 0.271,0.188 10 false *2
*1 Armrest Lock Plate
*2 No. 1 Armrest Plate


Remove the bolt, armrest lock plate, No. 1 armrest plate and rear seat armrest assembly RH from the rear No. 1 seatback frame.


Hide 7.REMOVE CENTER SEAT HINGE SPACER

B278702

a.

Remove the center seat hinge spacer from the rear seat armrest assembly RH.


Hide 8.REMOVE SEATBACK SPRING

a.
B276714

Using needle nose pliers, remove the seatback spring.


Hide 9.REMOVE REAR NO. 1 SEATBACK ASSEMBLY

a.
B278703

Remove the 4 bolts and rear No. 1 seatback assembly from the rear No. 1 seat cushion assembly.


Hide 10.REMOVE REAR NO. 1 SEATBACK COVER

a.

Detach the 2 hooks and roll up the rear No. 1 seatback cover.

B278704


b.
B207788

Remove the hog rings from the wires of the rear No. 1 seatback cover. Then roll up the rear No. 1 seatback cover.


c.
B209094

Remove the hog rings and detach the 2 straps of the rear No. 1 seatback cover.


d.
B276725

Pass the 2 straps of the rear No. 1 seatback cover through the 2 holes of the No. 1 seatback pad RH to the surface.


e.

Roll up the rear No. 1 seatback cover to detach the 2 hooks.

B278705


f.
B278843

Remove the hog rings from the center of the No. 1 seatback pad and roll up the rear No. 1 seatback cover.


g.
B207581

Remove the hog rings from the upper part of the rear No. 1 seatback frame. Then roll up the rear No. 1 seatback cover.


h.
B207089

Detach the 4 claws and remove the 2 rear seat headrest supports.


i.
B207091

Remove the hog rings and rear No. 1 seatback cover from the No. 1 seatback pad RH.


Hide 11.REMOVE NO. 1 SEATBACK PAD RH

a.
B207090

Remove the No. 1 seatback pad RH from the rear No. 1 seatback frame.


Hide 12.REMOVE REAR SEAT CUSHION EDGE PROTECTOR

B278707
2.667,2.229 2.396,2.229 2.396,2.229 2.281,2.542 true 2.719,2.167 3.01,2.458 0.292,0.292 10 false *1
*1 Cushion Edge Tab


a.

Bend out the 2 cushion edge tabs.

NOTICE:

Be careful not to break the cushion edge tabs.



b.

Remove the 2 rear seat cushion edge protectors from the 2 cushion edge tabs.


Hide 13.REMOVE SEAT CUSHION COVER WITH PAD

B278709
4.118,1.171 4.268,1.318 0.149,0.147 10 *1 4.111,1.234 4.034,1.234 4.034,1.234 3.969,1.329 false
*1 Rear No. 1 Seat Cushion Cover Lower Part - -


a.

Detach the hook.


b.

Remove the hog rings and fold back the lower part of the rear No. 1 seat cushion cover.


c.

Remove the hog rings and the seat cushion cover with pad from the rear No. 1 seat cushion frame.


Hide 14.REMOVE REAR NO. 1 SEAT CUSHION COVER

a.
B207084

Remove the hog rings and rear No. 1 seat cushion cover from the rear No. 1 seat cushion pad.


Hide 15.REMOVE REAR SEAT CUSHION EDGE PROTECTOR RH

B278711

a.

Remove the rear seat cushion edge protector RH from the reclining adjuster lower arm sub-assembly RH.


Hide 16.REMOVE NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY RH

a.
B281157

Remove the 4 bolts and No. 1 seat cushion frame sub-assembly RH.


Hide 17.REMOVE SEAT TRACK ADJUSTING HANDLE

a.
B278713

Using a screwdriver, detach the 2 springs and remove the seat track adjusting handle as shown in the illustration.

HINT:
B278715

The seat track adjusting handle will get caught on the springs when removing it. Detach the springs to remove the seat track adjusting handle.



Hide 18.REMOVE RECLINING ADJUSTER LOWER ARM SUB-ASSEMBLY LH

a.
B155370

Remove the 3 bolts and reclining adjuster lower arm sub-assembly LH from the rear seat inner track assembly RH.


Hide 19.REMOVE RECLINING ADJUSTER LOWER ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.