Home › Vehicle Interior › SEAT › REAR NO. 1 SEAT ASSEMBLY(for Captain Seat Type)
RM1880E _58 Vehicle Interior _013243 SEAT _0068643 REAR NO. 1 SEAT ASSEMBLY(for Captain Seat Type) A

SEAT  REAR NO. 1 SEAT ASSEMBLY(for Captain Seat Type)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the RH side.



PROCEDURE

Hide 1.INSTALL RECLINING ADJUSTER LOWER ARM SUB-ASSEMBLY LH

a.

Install the reclining adjuster lower arm sub-assembly LH to the rear seat inner track assembly RH with the 3 bolts.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 2.INSTALL RECLINING ADJUSTER LOWER ARM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 3.INSTALL SEAT TRACK ADJUSTING HANDLE

a.
B278641
3.271,2.104 3.354,2.104 false
V100135

MP Grease


Apply MP grease to the locations of the seat track adjusting handle shown in the illustration.


b.
B280051
3.281,3.365 3.365,3.365 false
V100135

MP Grease


Apply MP grease to the locations of the rear seat outer track assembly RH and rear seat inner track assembly RH shown in the illustration.


c.
B278714

Attach the 2 springs to install the seat track adjusting handle to the rear seat outer track assembly RH and rear seat inner track assembly RH.

HINT:
B278715

The seat track adjusting handle will get caught on the springs when installing it. Detach the springs to install the seat track adjusting handle.



Hide 4.INSTALL NO. 1 SEAT CUSHION FRAME SUB-ASSEMBLY RH

a.

Install the No. 1 seat cushion frame sub-assembly RH with the 4 bolts.

Torque:
20 N*m (199 kgf*cm, 14 ft.*lbf)


Hide 5.INSTALL REAR SEAT CUSHION EDGE PROTECTOR RH

B278712

a.

Install the rear seat cushion edge protector RH to the reclining adjuster lower arm sub-assembly RH.


Hide 6.INSTALL REAR NO. 1 SEAT CUSHION COVER

a.
B207448
1.74,2.448 1.625,2.448 false 1.625,2.448 1.438,3.177 false 1.792,2.354 2.073,2.646 0.281,0.292 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the rear No. 1 seat cushion cover to the rear No. 1 seat cushion pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




Hide 7.INSTALL SEAT CUSHION COVER WITH PAD

a.

Set the seat cushion cover with pad in place.


b.

Using hog ring pliers, install the seat cushion cover with pad to the rear No. 1 seat cushion frame with new hog rings.

B278710
3.896,3.01 3.75,3 3.75,3 3.75,3.292 false 4.177,1.281 4.094,1.281 4.094,1.281 4.01,1.448 false 3.938,2.948 4.198,3.208 0.26,0.26 10 false *2 4.188,1.188 4.438,1.396 0.25,0.208 10 false *1
*1 Rear No. 1 Seat Cushion Cover Lower Part *2 Hog Ring Pliers


NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




c.

Return the lower part of the rear No. 1 seat cushion cover to its original position, and then, using hog ring pliers, install new hog rings.


d.

Attach the hook.


Hide 8.INSTALL REAR SEAT CUSHION EDGE PROTECTOR

B278708
0.594,0.438 0.76,0.438 0.76,0.438 1.094,0.271 true 0.396,0.354 0.656,0.604 0.26,0.25 10 false *1
*1 Cushion Edge Tab


a.

Install the 2 cushion edge protectors to the 2 cushion edge tabs.


b.

Return the 2 cushion edge tabs to their original positions.

NOTICE:

Be careful not to break the cushion edge tabs.



Hide 9.INSTALL NO. 1 SEATBACK PAD RH

a.
B207459

Install the No. 1 seatback pad RH to the rear No. 1 seatback frame.


Hide 10.INSTALL REAR NO. 1 SEATBACK COVER

a.
B207460
2.083,2.5 1.833,2.5 1.833,2.5 1.656,3.229 false 2.125,2.438 2.563,2.833 0.438,0.396 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, attach the 2 straps of the rear No. 1 seatback cover to the No. 1 seatback pad RH with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.
B207457

Attach the 4 claws to install the 2 headrest supports.


c.
B207582
1.792,2.469 1.677,2.469 false 1.677,2.469 1.49,3.208 false 1.833,2.406 2.115,2.719 0.281,0.313 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the upper part of the rear No. 1 seatback cover to the rear No. 1 seatback frame with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




d.
B278844
1.552,2.677 1.792,2.677 1.792,2.677 1.677,3.229 false 1.375,2.594 1.698,2.896 0.323,0.302 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, install the center of the rear No. 1 seatback cover to the No. 1 seatback pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




e.

Attach the 2 hooks.

B278706


f.
B276726

Pass the 2 straps of the rear No. 1 seatback cover through the 2 holes of the No. 1 seatback pad RH to the backside.


g.
B209095
1.729,2.521 1.625,2.521 false 1.625,2.521 1.406,3.24 false 1.76,2.427 2.021,2.667 0.26,0.24 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, attach the 2 straps of the rear No. 1 seatback cover to the rear No. 1 seatback frame with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




h.
B207798
1.677,3.25 1.5,2.667 1.5,2.667 1.167,2.667 false 0.969,2.563 1.281,2.76 0.313,0.198 10 false *1
*1 Hog Ring Pliers


Using hog ring pliers, attach the 2 wires at the bottom of the rear No. 1 seatback cover with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




i.

Attach the 2 hooks.

B278716


Hide 11.INSTALL REAR NO. 1 SEATBACK ASSEMBLY

a.

Install the rear No. 1 seatback assembly to the rear No. 1 seat cushion assembly with the 4 bolts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 12.INSTALL SEATBACK SPRING

a.

Using needle nose pliers, install the seatback spring.


Hide 13.INSTALL CENTER SEAT HINGE SPACER

a.

Install the center seat hinge spacer to the rear seat armrest assembly RH.


Hide 14.INSTALL REAR SEAT ARMREST ASSEMBLY RH

a.

Install the rear seat armrest assembly, No. 1 armrest plate and armrest lock plate with the bolt.

Torque:
20 N*m (200 kgf*cm, 14 ft.*lbf)


b.

Attach the fastener to close the rear seat armrest cover.


Hide 15.INSTALL REAR SEAT CUSHION SHIELD RH

B342528
0.51,1.344 0.948,1.615 0.438,0.271 10 false (2) 1.417,1.448 1.854,1.719 0.438,0.271 10 false (1)

a.

Attach the claw, and then attach the rear part of the rear seat cushion shield RH in the order shown in the illustration to install the rear seat cushion shield RH.


b.

Install the 2 screws.


Hide 16.INSTALL RECLINING ADJUSTER RELEASE HANDLE RH

a.
B277632

Attach the claw to install the reclining adjuster release handle RH.


Hide 18.INSTALL REAR SEAT INNER CUSHION SHIELD RH

B257934
1.625,1.271 1.885,1.5 0.26,0.229 10 false (1) 1.958,1.042 2.188,1.25 0.229,0.208 10 false (2) 2.615,1.24 2.875,1.479 0.26,0.24 10 true (3)

a.

Attach the claw, and then attach the rear part of the rear seat inner cushion shield RH in the order shown in the illustration to install the rear seat inner cushion shield RH.


b.

Install the 2 screws.


Hide 19.INSTALL REAR SEAT HEADREST ASSEMBLY

a.

Install the rear seat headrest assembly.