Wear protective gloves. Sharp areas on the parts may injure your hands.
1.REMOVE REAR SEAT HEADREST ASSEMBLY
Remove the rear seat headrest assembly.
2.REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH
Remove the screw and No. 1 reclining adjuster release handle LH.
3.REMOVE REAR NO. 1 SEAT RECLINING COVER LH
|
Pull |
|
Pull Up |
Remove the screw.
Pull the rear No. 1 seat reclining cover LH to detach the claw.
Pull up the rear No. 1 seat reclining cover LH to detach the guide and remove the rear No. 1 seat reclining cover LH.
4.REMOVE REAR NO. 1 SEAT RECLINING COVER RH
|
Pull |
|
Pull Up |
Remove the screw.
Pull the rear No. 1 seat reclining cover RH to detach the claw.
Pull up the rear No. 1 seat reclining cover RH to detach the guide and remove the rear No. 1 seat reclining cover RH.
5.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH
6.REMOVE REAR NO. 1 SEATBACK ASSEMBLY
Remove the 4 bolts and rear No. 1 seatback assembly.
7.REMOVE REAR NO. 1 SEATBACK COVER LH
Detach the 3 hooks.
Roll up the rear No. 1 seatback cover LH to detach the 2 hooks.
Detach the 4 claws and remove the 2 rear seat headrest supports.
Remove the hog rings and rear No. 1 seatback cover from the No. 1 seatback pad LH.
8.REMOVE NO. 1 SEATBACK PAD LH
Remove the No. 1 seatback pad LH from the rear No. 1 seatback frame.
9.REMOVE REAR SEATBACK LOCK RELEASE BUTTON
| *1 | Protective Tape |
| *2 | Reclining Release Handle Sub-assembly |
Using 2 clip removers, remove the 2 rear seatback lock release buttons from the reclining release handle sub-assembly.
Tape the clip remover tips before use.
If a rear seatback lock release button is damaged, replace it with a new one.
10.REMOVE REAR SEAT LOCK COVER LH
| *1 | Reclining Release Handle Sub-assembly |
Remove the 2 screws and rear seat lock cover LH from the rear seat lock assembly LH.
Pass the reclining release handle sub-assembly through the hole of the rear seat lock cover LH.
11.REMOVE RECLINING RELEASE HANDLE SUB-ASSEMBLY
Remove the reclining release handle sub-assembly from the outer seat track assembly LH as shown in the illustration.
12.REMOVE REAR PROTECTOR PIPE
Remove the 2 rear protector pipes.
13.REMOVE REAR SEAT OUTER LOCK COVER LH
Remove the screw.
Detach the 2 claws and remove the rear seat outer lock cover LH.
14.REMOVE REAR SEAT INNER LOCK COVER LH
Detach the claw and guide and remove the rear seat inner lock cover LH from the rear seat lock assembly RH.
15.REMOVE LOWER SEAT TRACK RAIL PROTECTOR LH
Detach the 4 claws and remove the lower seat track rail protector LH from the outer seat track assembly LH.
16.REMOVE LOWER SEAT TRACK RAIL PROTECTOR RH
Remove the screw.
Detach the 2 claws and remove the lower seat track rail protector RH from the inner seat track assembly LH.
17.REMOVE NO. 1 SEAT LEG LINK
Remove the 2 E-rings, 2 washers and No. 1 seat leg link.
Remove the 2 washers from the rear seat hinge assembly RH and rear seat lock assembly RH.
18.REMOVE REAR SEAT HINGE ASSEMBLY LH
Remove the 2 nuts and rear seat hinge assembly LH from the outer seat track assembly LH.
19.REMOVE REAR SEAT HINGE ASSEMBLY RH
Use the same procedure described for the LH side.
20.REMOVE REAR SEAT LOCK CONTROL CABLE LH
| *1 | Fastening Tape |
| *2 | Rear No. 1 Seat Cushion Cover LH Lower Part |
| *3 | Cable End |
| *4 | Cable Clamp |
Detach the fastening tape and open the lower part of the rear No. 1 seat cushion cover LH.
Detach the cable clamp and remove the E-ring and washer.
Disconnect the rear seat lock control cable LH and remove the washer from the rear seat lock assembly LH.
Detach the cable clamp.
Twist the cable end in the direction indicated by the arrow to disconnect the cable end and remove the rear seat lock control cable LH from the rear seat lock assembly RH.
21.REMOVE REAR SEAT CUSHION SUPPORT SPRING
Using needle nose pliers, remove the rear seat cushion support spring.
22.REMOVE REAR SEAT LOCK ASSEMBLY LH
| *1 | Rear Seat Lock Link |
Remove the E-ring and washer and disconnect the rear seat lock link from the outer seat track assembly LH.
Remove the washer from the outer seat track assembly LH.
Remove the 2 nuts and rear seat lock assembly LH from the outer seat track assembly LH.
23.REMOVE REAR SEAT NO. 1 CUSHION SUPPORT SPRING
Using needle nose pliers, remove the rear seat No. 1 cushion support spring.
24.REMOVE REAR SEAT LOCK ASSEMBLY RH
Using a T40 "TORX" socket wrench, remove the "TORX" bolt and rear seat lock assembly RH from the inner seat track assembly LH.
25.REMOVE SEAT TRACK ADJUSTING HANDLE
Perform this procedure when removing and reinstalling or replacing only the seat track adjusting handle.
Operate the seat track adjusting handle and move the outer seat track assembly LH and inner seat track assembly LH to the position shown in the illustration.
| *1 | Seat Track Adjusting Handle Lock | *2 | Outer Seat Track Assembly LH |
| *3 | Inner Seat Track Assembly LH | *4 | Seat Track Adjusting Handle |
Insert a screwdriver into the outer seat track assembly LH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.
| *1 | Screwdriver | *2 | Outer Seat Track Assembly LH |
| *3 | Seat Track Adjusting Handle Lock | *4 | Seat Track Adjusting Handle |
Do not use excessive force to pull out the seat track adjusting handle.
Insert a screwdriver into the inner seat track assembly LH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.
| *1 | Screwdriver | *2 | Inner Seat Track Assembly LH |
| *3 | Seat Track Adjusting Handle Lock | *4 | Seat Track Adjusting Handle |
Do not use excessive force to pull out the seat track adjusting handle.
Pull and remove the seat track adjusting handle from the outer seat track assembly LH and inner seat track assembly LH.
26.REMOVE REAR SEAT TRACK ASSEMBLY LH
Operate the seat track adjusting handle and move the outer seat track assembly LH and inner seat track assembly LH to the foremost position.
Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts.
Operate the seat track adjusting handle and move the outer seat track assembly LH and inner seat track assembly LH to the position shown in the illustration.
| *1 | Seat Track Adjusting Handle Lock | *2 | Outer Seat Track Assembly LH |
| *3 | Inner Seat Track Assembly LH | *4 | Seat Track Adjusting Handle |
Insert a screwdriver into the outer seat track assembly LH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.
| *1 | Screwdriver | *2 | Outer Seat Track Assembly LH |
| *3 | Seat Track Adjusting Handle Lock | *4 | Seat Track Adjusting Handle |
Do not use excessive force to pull out the seat track adjusting handle.
Insert a screwdriver into the inner seat track assembly LH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.
| *1 | Screwdriver | *2 | Inner Seat Track Assembly LH |
| *3 | Seat Track Adjusting Handle Lock | *4 | Seat Track Adjusting Handle |
Do not use excessive force to pull out the seat track adjusting handle.
Pull the seat track adjusting handle to the position shown in the illustration.
| *1 | Seat Track Adjusting Handle Lock | *2 | Outer Seat Track Assembly LH |
| *3 | Inner Seat Track Assembly LH | *4 | Seat Track Adjusting Handle |
At this time, do not remove the seat track adjusting handle.
At this time, do not engage the lock of the seat track adjusting handle.
Operate the seat track adjusting handle and move the outer seat track assembly LH and inner seat track assembly LH to the rearmost position.
At this time, do not engage the lock of the seat track adjusting handle.
Pull and remove the seat track adjusting handle from the outer seat track assembly LH and inner seat track assembly LH.
Using a T40 "TORX" socket wrench, remove the "TORX" bolt and outer seat track assembly LH.
Using a T40 "TORX" socket wrench, remove the "TORX" bolt and inner seat track assembly LH.
27.REMOVE REAR NO. 1 SEAT CUSHION COVER LH
| *1 | Rear No. 1 Seat Cushion Cover LH Front Part |
| *2 | Fastening Tape |
| *3 | Fastener |
Detach the fastening tape and open the front part of the rear No. 1 seat cushion cover LH.
Remove the hog rings.
Detach the 2 fasteners and open the rear No. 1 seat cushion cover LH.
Remove the hog rings.
| *1 | No. 1 Fold Seat Stopper Band Assembly |
Pull out the No. 1 fold seat stopper band assembly from the rear No. 1 seat cushion cover LH.
Remove the hog rings and rear No. 1 seat cushion cover LH from the rear No. 1 seat cushion pad LH.
28.REMOVE NO. 1 SEAT CUSHION PAD LH
Remove the rear No. 1 seat cushion pad LH from the rear No. 1 seat cushion frame.
29.REMOVE NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
Untie the No. 1 fold seat stopper band assembly from the No. 1 seat cushion frame as shown in the illustration and remove the No. 1 fold seat stopper band assembly.