Wear protective gloves. Sharp areas on the parts may injure your hands.
1.REMOVE REAR SEAT HEADREST ASSEMBLY
Remove the rear seat headrest assembly.
2.REMOVE REAR NO. 1 SEAT RECLINING COVER LH
|
Pull |
|
Pull Up |
Remove the screw.
Pull the rear No. 1 seat reclining cover LH to detach the claw.
Pull up the rear No. 1 seat reclining cover LH to detach the guide and remove the rear No. 1 seat reclining cover LH.
3.REMOVE RECLINING ADJUSTER RELEASE HANDLE RH
Remove the screw and reclining adjuster release handle RH.
4.REMOVE REAR NO. 1 SEAT RECLINING COVER RH
|
Pull |
|
Pull Up |
Remove the screw.
Pull the rear No. 1 seat reclining cover RH to detach the claw.
Pull up the rear No. 1 seat reclining cover RH to detach the guide and remove the rear No. 1 seat reclining cover RH.
5.REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH
6.REMOVE REAR NO. 1 SEATBACK ASSEMBLY RH
Remove the 4 bolts and rear No. 1 seatback assembly RH.
7.REMOVE REAR NO. 1 SEATBACK COVER RH
| *1 | Hook | *2 | Fastener |
Detach the 3 hooks.
Open the fastener and roll up the rear No. 1 seatback cover RH.
w/ Center Armrest:
Remove the 2 nuts and hog rings.
Slightly pull out the rear seat armrest assembly RH, pull the rear No. 1 seatback cover RH out from the rear of the rear seat armrest, and then remove the rear seat armrest assembly RH.
Roll up the rear No. 1 seatback cover RH and detach the 2 hooks.
Detach the 4 claws and remove the 2 rear seat headrest supports.
Remove the hog rings and rear No. 1 seatback cover RH from the No. 1 seatback pad RH.
8.REMOVE REAR SEAT ARMREST ARM LH (w/ Center Armrest)
Remove the bolt and rear seat armrest arm LH.
9.REMOVE REAR SEAT ARMREST BUSH LH (w/ Center Armrest)
Remove the rear seat armrest bush LH from the rear seat armrest arm LH.
10.REMOVE REAR SEAT ARMREST ARM RH (w/ Center Armrest)
Use the same procedure described for the LH side.
11.REMOVE REAR SEAT ARMREST BUSH RH (w/ Center Armrest)
Use the same procedure described for the LH side.
12.REMOVE NO. 1 SEATBACK PAD RH
Remove the rear No. 1 seatback pad RH from the rear No. 1 seatback frame.
13.REMOVE REAR SEATBACK LOCK RELEASE BUTTON
| *1 | Protective Tape |
| *2 | Reclining Release Handle Sub-assembly |
Using 2 clip removers, remove the 2 rear seatback lock release buttons from the reclining release handle sub-assembly.
Tape the clip remover tips before use.
If a rear seatback lock release button is damaged, replace it with a new one.
14.REMOVE REAR SEAT LOCK COVER RH
| *1 | Reclining Release Handle Sub-assembly |
Remove the 2 screws and rear seat lock cover RH.
Pass the reclining release handle sub-assembly through the hole of the rear seat lock cover RH.
15.REMOVE RECLINING RELEASE HANDLE SUB-ASSEMBLY
Remove the reclining release handle sub-assembly from the outer seat track assembly RH as shown in the illustration.
16.REMOVE REAR PROTECTOR PIPE
Remove the 2 rear protector pipes.
17.REMOVE REAR SEAT OUTER LOCK COVER RH
Remove the screw.
Detach the 2 claws and remove the rear seat outer lock cover RH.
18.REMOVE REAR SEAT INNER LOCK COVER RH
Detach the claw and guide and remove the rear seat inner lock cover RH.
19.REMOVE LOWER SEAT TRACK RAIL PROTECTOR LH
Remove the screw.
Detach the 2 claws and remove the lower seat track rail protector LH from the inner seat track assembly RH.
20.REMOVE LOWER SEAT TRACK RAIL PROTECTOR RH
Detach the 4 claws and remove the lower seat track rail protector RH from the outer seat track assembly RH.
21.REMOVE NO. 1 SEAT LEG LINK
Remove the 2 E-rings, 2 washers and No. 1 seat leg link.
Remove the 2 washers from the rear seat hinge assembly LH and rear seat lock assembly LH.
22.REMOVE REAR SEAT HINGE ASSEMBLY LH
Remove the 2 nuts and rear seat hinge assembly LH from the inner seat track assembly RH.
23.REMOVE REAR SEAT HINGE ASSEMBLY RH
Use the same procedure described for the LH side.
24.REMOVE REAR SEAT LOCK CONTROL CABLE RH
| *1 | Fastening Tape |
| *2 | Rear No. 1 Seat Cushion Cover RH Lower Part |
| *3 | Cable End |
| *4 | Cable Clamp |
Detach the fastening tape and open the lower part of the rear No. 1 seat cushion cover RH.
Detach the cable clamp and remove the E-ring and washer.
Disconnect the rear seat lock control cable RH and remove the washer from the rear seat lock assembly RH.
Detach the cable clamp.
Twist the cable end in the direction indicated by the arrow to disconnect the cable end and remove the rear seat lock control cable RH from the rear seat lock assembly LH.
25.REMOVE REAR SEAT CUSHION SUPPORT SPRING
Using needle nose pliers, remove the rear seat cushion support spring.
26.REMOVE REAR SEAT LOCK ASSEMBLY LH
Using a T40 "TORX" socket wrench, remove the "TORX" bolt and rear seat lock assembly LH from the inner seat track assembly RH.
27.REMOVE REAR SEAT NO. 1 CUSHION SUPPORT SPRING
Using needle nose pliers, remove the rear seat No. 1 cushion support spring.
28.REMOVE REAR SEAT LOCK ASSEMBLY RH
| *1 | Rear Seat Lock Link |
Remove the E-ring and washer and disconnect the rear seat lock link from the outer seat track assembly RH.
Remove the washer from the rear seat lock assembly LH.
Remove the 2 nuts and lock.
Remove the 2 nuts and rear seat lock assembly RH from the outer seat track assembly RH.
29.REMOVE SEAT TRACK ADJUSTING HANDLE
Perform this procedure when removing and reinstalling or replacing only the seat track adjusting handle.
Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the position shown in the illustration.
| *1 | Seat Track Adjusting Handle Lock | *2 | Inner Seat Track Assembly RH |
| *3 | Outer Seat Track Assembly RH | *4 | Seat Track Adjusting Handle |
Insert a screwdriver into the outer seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.
Do not use excessive force to pull out the seat track adjusting handle.
| *1 | Screwdriver | *2 | Outer Seat Track Assembly RH |
| *3 | Seat Track Adjusting Handle Lock | *4 | Seat Track Adjusting Handle |
Insert a screwdriver into the inner seat track assembly LH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.
Do not use excessive force to pull out the seat track adjusting handle.
| *1 | Screwdriver | *2 | Inner Seat Track Assembly RH |
| *3 | Seat Track Adjusting Handle Lock | *4 | Seat Track Adjusting Handle |
At this time, do not remove the seat track adjusting handle.
At this time, do not engage the lock of the seat track adjusting handle.
Pull and remove the seat track adjusting handle from the outer seat track assembly RH and inner seat track assembly RH.
30.REMOVE REAR SEAT TRACK ASSEMBLY RH
Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the foremost position.
Using a T40 "TORX" socket wrench, remove the 4 "TORX" bolts.
Operate the seat track adjusting handle and move the outer seat track assembly RH and inner seat track assembly RH to the position shown in the illustration.
| *1 | Seat Track Adjusting Handle Lock | *2 | Inner Seat Track Assembly RH |
| *3 | Outer Seat Track Assembly RH | *4 | Seat Track Adjusting Handle |
Insert a screwdriver into the outer seat track assembly RH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.
Do not use excessive force to pull out the seat track adjusting handle.
| *1 | Screwdriver | *2 | Outer Seat Track Assembly RH |
| *3 | Seat Track Adjusting Handle Lock | *4 | Seat Track Adjusting Handle |
Insert a screwdriver into the inner seat track assembly LH and disengage the lock of the seat track adjusting handle. While maintaining that state, pull out the seat track adjusting handle to the position shown in the illustration, and then remove the screwdriver.
Do not use excessive force to pull out the seat track adjusting handle.
| *1 | Screwdriver | *2 | Inner Seat Track Assembly RH |
| *3 | Seat Track Adjusting Handle Lock | *4 | Seat Track Adjusting Handle |
Pull the seat track adjusting handle to the position shown in the illustration.
| *1 | Seat Track Adjusting Handle Lock | *2 | Inner Seat Track Assembly RH |
| *3 | Outer Seat Track Assembly RH | *4 | Seat Track Adjusting Handle |
Operate the seat track adjusting handle and move the outer seat track assembly LH and inner seat track assembly LH to the rearmost position.
At this time, do not engage the lock of the seat track adjusting handle.
Pull and remove the seat track adjusting handle from the outer seat track assembly RH and inner seat track assembly RH.
Using a T40 "TORX" socket wrench, remove the "TORX" bolt and outer seat track assembly RH.
Using a T40 "TORX" socket wrench, remove the "TORX" bolt and inner seat track assembly RH.
31.REMOVE REAR NO. 1 SEAT CUSHION COVER RH
| *1 | Rear No. 1 Seat Cushion Cover RH Front Part |
| *2 | Fastening Tape |
| *3 | Fastener |
Detach the fastening tape and open the front part of the rear No. 1 seat cushion cover RH.
Remove the hog rings.
Detach the 2 fasteners and open the rear No. 1 seat cushion cover RH.
Remove the hog rings.
| *1 | No. 1 Fold Seat Stopper Band Assembly |
Pull out the No. 1 fold seat stopper band assembly.
Remove the hog rings and rear No. 1 seat cushion cover from the rear No. 1 seat cushion pad.
Pass the rear center seat lap type belt assembly and rear seat lap type belt assembly RH through the hole of the rear No. 1 seat cushion cover RH.
32.REMOVE NO. 1 SEAT CUSHION PAD RH
Pass the rear center seat lap type belt assembly and rear seat lap type belt assembly RH through the hole of the No. 1 seat cushion pad RH.
Remove the No. 1 seat cushion pad RH from the rear No. 1 seat cushion frame.
33.REMOVE REAR CENTER SEAT LAP TYPE BELT ASSEMBLY
34.REMOVE REAR SEAT LAP TYPE BELT ASSEMBLY LH
35.REMOVE NO. 1 FOLD SEAT STOPPER BAND ASSEMBLY
Untie the No. 1 fold seat stopper band assembly from the rear No. 1 seat cushion frame as shown in the illustration and remove the No. 1 fold seat stopper band assembly.