Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)
RM1880E _58 Vehicle Interior _013245 HEATING / AIR CONDITIONING _0068660 AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System) U

HEATING / AIR CONDITIONING  AIR CONDITIONING SYSTEM(for Automatic Air Conditioning System)  TERMINALS OF ECU  


CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY


E224847
2.927,0.115 3.323,0.344 0.396,0.229 4.479,0.115 4.875,0.344 0.396,0.229 2.99,0.156 3.396,0.354 0.406,0.198 10 false G94 4.542,0.156 4.938,0.417 0.396,0.26 10 false G95

a.

Disconnect the G94 air conditioning amplifier assembly connector.


b.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G94-1 (GND) - Body ground L - Body ground Ground Always Below 1 Ω
G94-5 (+B1) - G94-1 (GND) L-Y - L Battery power source Always 11 to 14 V
G94-6 (IG+) - G94-1 (GND) R-L - L Ignition power source Ignition switch off Below 1 V
Ignition switch ON 11 to 14 V
G94-13 (MGC) - Body ground B - Body ground Magnet clutch signal Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
G94-14 (HR) - Body ground L-W - Body ground HTR relay signal Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V

If the result is not as specified, there may be a malfunction on the wire harness side.



c.

Reconnect the G94 air conditioning amplifier assembly connector.


d.

Measure the voltage and resistance according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G94-2 (BLW) - Body ground L-B - Body ground Blower motor speed control voltage
·

Ignition switch ON

·

Blower switch on (LO level)


Pulse generation
(See waveform 1)
G94-3 (AOF) - G94-1 (GND) Y-B - L Mode damper servo operation voltage
·

Ignition switch ON

·

Mode switch DEF


Below 1 V
·

Ignition switch ON

·

Mode switch FACE


11 to 14 V
G94-4 (AOD) - G94-1 (GND) R-B - L Mode damper servo operation voltage
·

Ignition switch ON

·

Mode switch FACE


Below 1 V
·

Ignition switch ON

·

Mode switch DEF


11 to 14 V
G94-7 (ACT) - G94-1 (GND) R-L - L Magnet clutch on permit input signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


11 to 14 V
G94-8 (TW) - G94-1 (GND) P - L Engine coolant temperature sensor signal Ignition switch ON Pulse generation
G94-9 (SPD) - Body ground V-W - Body ground Vehicle speed signal Driving at approximately 20 km/h (12 mph) Pulse generation
(See waveform 2)
G94-13 (MGC) - Body ground B - Body ground Magnet clutch signal
·

Engine idling

·

A/C switch on (magnet clutch on permitted)


Below 1 V
·

Engine idling

·

A/C switch off or on (magnet clutch on not permitted)


11 to 14 V
G94-17 (AMH) - G94-1 (GND) L - L Air mix damper servo operation signal
·

Ignition switch ON

·

Temperature switch MAX HOT


11 to 14 V
·

Ignition switch ON

·

Temperature switch MAX COLD


Below 1 V
G94-18 (TAMO) - G94-1 (GND) P - L Ambient temperature signal Ignition switch ON Pulse generation
G94-19 (AMC) - G94-1 (GND) R-W - L Air mix damper servo operation signal
·

Ignition switch ON

·

Temperature switch MAX HOT


Below 1 V
·

Ignition switch ON

·

Temperature switch MAX COLD


11 to 14 V
G94-21 (AC1) - G94-1 (GND) Y - L Idle-up request signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
G94-22 (AIR) - G94-1 (GND) L-W - L Recirculation damper servo operation voltage
·

Ignition switch ON

·

Fresh switch on


Below 1 V
·

Ignition switch ON

·

Recirculation switch on


11 to 14 V
G94-23 (AIF) - G94-1 (GND) G-Y - L Recirculation damper servo operation voltage
·

Ignition switch ON

·

Recirculation switch on


Below 1 V
·

Ignition switch ON

·

Fresh switch on


11 to 14 V
G95-1 (TE) - G95-14 (SG-4) G - P No. 1 cooler thermistor signal
·

Ignition switch ON

·

Evaporator temperature 0°C (32°F)


2 to 2.4 V
·

Ignition switch ON

·

Evaporator temperature 15°C (59°F)


1.4 to 1.8 V
G95-2 (S5-3) - G94-1 (GND) W-R - L Power supply for solar sensor Ignition switch ON 4.5 to 5.5 V
G95-5 (PSW) - G94-1 (GND) Y-B - L Air conditioner pressure sensor signal
·

Engine idling

·

Refrigerant pressure normal


Below 1 V
·

Engine idling

·

Refrigerant pressure less than 0.196 MPa (2.0 kgf/cm2, 28 psi) or more than 3.14 MPa (32.0 kgf/cm2, 455 psi)


11 to 14 V
G95-7 (TS) - G95-2 (S5-3) L-W - W-R Solar sensor signal
·

Ignition switch ON

·

Solar sensor subjected to electric light

·

Vehicle indoors


0.8 to 4.3 V
·

Ignition switch ON

·

Solar sensor covered with cloth

·

Vehicle indoors


Below 0.8 V
G95-9 (VER) - Body ground* R - Body ground Steering wheel location information signal Always Below 1 Ω
G95-11 (SG-2) - Body ground L-Y - Body ground Ground for pulse position sensor (Mode damper servo) Always Below 1 Ω
G95-13 (SG-3) - Body ground BR-Y - Body ground Ground for cooler thermistor Always Below 1 Ω
G95-14 (SG-4) - Body ground P - Body ground Ground for No. 1 cooler thermistor Always Below 1 Ω
G95-16 (PIB) - G95-21 (SG-7) R-L - LG-R Input signal for pulse position sensor (recirculation damper servo)
·

Ignition switch ON

·

Air inlet control recirculation to fresh or vice versa


Pulse generation
G95-17 (PIA) - G95-21 (SG-7) P-B - LG-R Input signal for pulse position sensor (recirculation damper servo)
·

Ignition switch ON

·

Air inlet control recirculation to fresh or vice versa


Pulse generation
G95-18 (TR) - G95-13 (SG-3) GR - BR-Y Cooler thermistor signal
·

Ignition switch ON

·

Cabin temperature 25°C (77°F)


1.8 to 2.2 V
·

Ignition switch ON

·

Cabin temperature 40°C (104°F)


1.2 to 1.6 V
G95-20 (SG-1) - Body ground BR-Y - Body ground Ground for pulse position sensor (air mix damper servo) Always Below 1 V
G95-21 (SG-7) - Body ground LG-R - Body ground Ground for pulse position sensor (recirculation damper servo) Always Below 1 Ω
G95-23 (PMB) - G95-20 (SG-1) W-L - BR-Y Input signal for pulse position sensor (air mix damper servo)
·

Ignition switch ON

·

Temperature switch MAX HOT to MAX COLD


Pulse generation
G95-24 (PMA) - G95-20 (SG-1) W-R - BR-Y Input signal for pulse position sensor (air mix damper servo)
·

Ignition switch ON

·

Temperature switch MAX COLD to MAX HOT


Pulse generation
G95-25 (POB) - G95-11(SG-2 ) LG - L-Y Input signal for pulse position sensor (mode damper servo)
·

Ignition switch ON

·

Mode control FACE to DEF or vice versa


Pulse generation
G95-26 (POA) - G95-11 (SG-2) L-O - L-Y Input signal for pulse position sensor (mode damper servo)
·

Ignition switch ON

·

Mode control FACE to DEF or vice versa


Pulse generation

*: for LHD

If the result is not as specified, the air conditioning amplifier assembly may have a malfunction.



e.
E171008
2.741,1.411 3.091,1.568 0.35,0.157 10 GND

Using an oscilloscope, check waveform 1.

Blower motor control signal
Item Content
Terminal No. (Symbol) G94-2 (BLW) - Body ground
Tool Setting 1 V/DIV., 50 μsec./DIV.
Condition Ignition switch ON, Blower switch on (LO level)

HINT:

When the blower level is increased, the duty ratio changes accordingly.



f.
E169152
2.759,1.171 3.096,1.327 0.337,0.156 10 GND

Using an oscilloscope, check waveform 2.

Vehicle speed signal
Item Content
Terminal No. (Symbol) G94-9 (SPD) - Body ground
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Driving at approximately 20 km/h (12 mph)

HINT:

As the vehicle speed increases, the wavelength becomes shorter.




CHECK ECM


E170985
1.658,0.103 1.936,0.26 0.278,0.157 10 C75 1.585,0.062 1.982,0.291 0.397,0.229 2.955,0.103 3.239,0.26 0.284,0.157 10 C76 2.881,0.062 3.278,0.291 0.397,0.229 4.251,0.103 4.583,0.26 0.332,0.157 10 G88 4.177,0.062 4.574,0.291 0.397,0.229 5.543,0.103 5.849,0.26 0.306,0.157 10 G89 5.473,0.062 5.87,0.291 0.397,0.229

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G88-14 (THWO) - C75-3 (E1) P - BR Engine coolant temperature output signal Engine idling Pulse generation
G88-24 (AC1) - C75-3 (E1) Y - BR Idle-up request signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off


11 to 14 V
G88-25 (ACT) - C75-3 (E1) R-L - BR Magnet clutch on permit output signal
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch off or on (magnet clutch off)


Below 1 V
·

Engine idling

·

Blower switch on (LO level)

·

A/C switch on (magnet clutch on)


11 to 14 V
C75-32 (THW) - C75-28 (E2) B - BR Engine coolant temperature sensor signal
·

Engine idling

·

Engine coolant temperature 20°C (68°F)


0.2 to 1.0 V

If the result is not as specified, the ECM may have a malfunction.



CHECK ACCESSORY METER ASSEMBLY


E165586
3.438,0.188 3.861,0.345 0.423,0.157 10 G112 3.404,0.148 3.801,0.377 0.397,0.229

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G112-3 (TH+) - G112-2 (SG) W-G - BR-Y Ambient temperature sensor signal
·

Ignition switch ON

·

Ambient temperature 20 to 30°C (68 to 86°F)


1 to 1.6 V
Ambient temperature sensor signal
·

Ignition switch ON

·

Ambient temperature 30 to 50°C (86 to 122°F)


0.6 to 1 V
G112-9 (DATA) - G112-1 (GND1) P - LG Ambient temperature sensor signal Ignition switch ON Pulse generation

If the result is not as specified, the accessory meter assembly may have a malfunction.




CHECK COMBINATION METER ASSEMBLY


E165587
3.51,0.188 3.862,0.345 0.353,0.157 10 G19 3.439,0.148 3.836,0.377 0.397,0.229

a.

Measure the voltage according to the value(s) in the table below.

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
G19-6 (+S) - G19-22 (EP) V-R - Y Vehicle speed signal Driving at approximately 20 km/h (12 mph) Pulse generation
(See waveform 1)

If the result is not as specified, the combination meter assembly may have a malfunction.



b.
E169152
2.759,1.171 3.096,1.327 0.337,0.156 10 GND

Using an oscilloscope, check waveform 1.

Vehicle speed signal
Item Content
Terminal No. (Symbol) G19-6 (+S) - G19-22 (EP)
Tool Setting 5 V/DIV., 20 ms./DIV.
Condition Driving at approximately 20 km/h (12 mph)

HINT:

When the blower level is increased, the duty ratio changes accordingly.