Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR
RM1880E _58 Vehicle Interior _013245 HEATING / AIR CONDITIONING _0068671 COMPRESSOR A

HEATING / AIR CONDITIONING  COMPRESSOR  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL MAGNET CLUTCH ASSEMBLY

E171847

a.

Install the magnet clutch stator with the parts aligned as shown in the illustration.


b.
E155204

Using a snap ring expander, install a new snap ring with the chamfered side facing outward.


c.
E155205

Using a snap ring expander, install the magnet clutch rotor and a new snap ring with the chamfered side facing outward.

NOTICE:

Do not damage the seal cover of the bearing when installing the snap ring.



d.

Install the magnet clutch washer(s) and magnet clutch hub.

NOTICE:

Do not change the combination of magnet clutch washer(s) used before disassembly.



e.
E172841
1.074,0.449 1.432,0.633 0.358,0.184 10 SST 0.807,0.796 1.027,0.577 false

for LHD:

i.

Using SST, hold the magnet clutch hub and install the bolt.

SST
09985-00270  

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)

NOTICE:

Make sure that there is no foreign matter or oil on the compressor shaft, bolt, and clutch hub.




f.
E171834
1.654,2.728 1.844,2.933 0.19,0.205 10 *1 1.844,2.81 2.407,2.81 false
*1 Battery


for RHD:

i.

Connect the battery to the magnet clutch assembly as shown in the illustration to fix the hub and rotor in place.


ii.

Wrap the drive belt around the rotor and securely hold it in place by hand.


iii.

Install the bolt.

Torque:
13 N*m (135 kgf*cm, 10 ft.*lbf)

NOTICE:
·

Make sure that there is no foreign matter or oil on the compressor shaft, bolt, and clutch hub.

·

When reusing the drive belt, check the belt for wear, cracks or other signs of damage.





Hide 2.INSTALL COOLER BRACKET

a.

for LHD:

i.

Connect the ground wire and install the cooler bracket with the screw.


ii.

Attach the clamp.



b.

for RHD:

i.

Connect the ground wire and install the cooler bracket with the screw.


ii.

Attach the clamp.



Hide 3.INSPECT MAGNET CLUTCH CLEARANCE

a.
E172840
0.084,0.045 0.288,0.245 0.204,0.2 10 *a 1.547,4.112 1.757,4.287 0.209,0.175 10 *1 1.72,4.201 2.381,4.201 false
*1 Battery
*a Component without harness connected
(Magnet Clutch Assembly)


for LHD:

i.

Clamp the cooler compressor in a vise between aluminum plates.


ii.

Set a dial indicator to the magnet clutch hub.


iii.

Connect the battery positive (+) lead to terminal 1 of the magnet clutch connector. Turn the magnet clutch on and off by connecting and disconnecting the battery negative (-) lead to and from the ground wire, and measure the clearance.

Standard clearance:

0.35 to 0.60 mm (0.014 to 0.024 in.)


If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using magnet clutch washers to obtain the standard clearance.

Magnet clutch washer thickness:

0.1 mm (0.004 in.)

0.3 mm (0.012 in.)

0.5 mm (0.020 in.)


NOTICE:

Adjustment should be performed with 3 or fewer magnet clutch washers.



iv.

Remove the cooler compressor from the vise.



b.
E171835
0.104,0.052 0.316,0.246 0.212,0.194 10 *a 2.482,4.14 2.67,4.307 0.188,0.167 10 *1 3.06,3.855 3.06,4.241 3.06,4.241 2.686,4.241 false
*1 Battery
*a Component without harness connected
(Magnet Clutch Assembly)


for RHD:

i.

Clamp the cooler compressor in a vise between aluminum plates.


ii.

Set a dial indicator to the magnet clutch hub.


iii.

Connect the battery positive (+) lead to terminal 1 of the magnet clutch connector. Turn the magnet clutch on and off by connecting and disconnecting the battery negative (-) lead to and from the ground wire, and measure the clearance.

Standard clearance:

0.35 to 0.60 mm (0.014 to 0.024 in.)


If the measured value is not within the standard clearance, remove the magnet clutch hub and adjust the clearance using magnet clutch washers to obtain the standard clearance.

Magnet clutch washer thickness:

0.1 mm (0.004 in.)

0.3 mm (0.012 in.)

0.5 mm (0.020 in.)


NOTICE:

Adjustment should be performed with 3 or fewer magnet clutch washers.



iv.

Remove the cooler compressor from the vise.