Home › Vehicle Exterior › WINDOW / GLASS › WINDOW DEFOGGER SWITCH(for Manual Cooler System)
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068697 WINDOW DEFOGGER SWITCH(for Manual Cooler System) G

WINDOW / GLASS  WINDOW DEFOGGER SWITCH(for Manual Cooler System)  INSPECTION  


PROCEDURE

Hide 1.INSPECT REAR WINDOW DEFOGGER SWITCH ASSEMBLY

B280808
1.969,2.792 2.271,3.167 2.271,3.167 2.427,3.167 true 2.156,2.635 2.458,2.406 2.458,2.406 2.646,2.406 true 1.552,1.052 0.969,1.052 true 2.51,3.063 2.927,3.313 0.417,0.25 10 false ILL- 2.708,2.333 3.177,2.667 0.469,0.333 10 false ILL+ 0.135,1.771 0.396,1.99 0.26,0.219 10 false *a 0.76,0.938 1,1.146 0.24,0.208 10 false *b
*a Component without harness connected
(Rear Window Switch Assembly)
*b Illumination Area


a.

Check the illumination area of the switch.

Standard measurement:
Measurement Condition Specified Condition
Battery positive (+) → 1 (ILL+)
Battery negative (-) → 2 (ILL+)
Illuminates


If the result is not as specified, replace the switch assembly.

HINT:

The ON/OFF indicator of the switch will not illuminate.



b.
B280809
1.771,2.792 2,3.167 2,3.167 2.083,3.167 true 1.292,2.792 1.083,3.167 1.083,3.167 1,3.167 true 1.573,0.688 1.042,0.688 true 0.833,3.083 1.135,3.354 0.302,0.271 10 false IG 2.125,3.083 2.396,3.344 0.271,0.26 10 false E 0.156,1.698 0.583,2 0.427,0.302 10 false *a 0.865,0.604 1.229,0.865 0.365,0.26 10 false *b
*a Component without harness connected
(Rear Window Switch Assembly)
*b ON/ OFF Indicator


Check ON/OFF indicator of the switch.

i.

Push the switch several times. Check that the ON/OFF indicator illuminates or turns off according to switch operation.

Standard measurement:
Measurement Condition Specified Condition Specified Condition
Battery positive (+) → 5 (IG)
Battery negative (-) → 3 (E)
Defogger switch ON Illuminates


If the result is not as specified, replace the switch assembly.

HINT:

The illumination area of the switch will not illuminate.




c.
B154298
1.76,1.427 2.083,0.583 2.083,0.583 2.167,0.583 true 1.469,1.438 1.083,0.583 1.083,0.583 1,0.583 true 0.844,0.49 1.24,0.74 0.396,0.25 10 false D 2.229,0.49 2.542,0.75 0.313,0.26 10 false E 0.104,0.094 0.51,0.396 0.406,0.302 10 false *a
*a Component without harness connected
(Rear Window Switch Assembly)


Measure the resistance of the switch.

Standard resistance:
Measurement Condition Specified Condition Specified Condition
4 (D) - 3 (E) ON Below 1 Ω
4 (D) - 3 (E) OFF 10 kΩ or higher


If the result is not as specified, replace the switch assembly.