Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068699 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Power Windows do not Operate at All  


DESCRIPTION

If all of the power windows do not operate, the power window regulator master switch assembly may have no power or may be malfunctioning.

WIRING DIAGRAM

B278482
0.615,0.958 1.844,1.354 1.229,0.396 10 false from Battery 4.75,0.542 5.219,0.844 0.469,0.302 10 false B 4.75,0.99 5.156,1.365 0.406,0.375 10 false BW 4.75,1.396 5.083,1.677 0.333,0.281 10 false E 4.896,1.99 6.573,2.594 1.677,0.604 10 false Power Window Regulator Master Switch Assembly 2.542,1.156 3.302,1.625 0.76,0.469 10 false DOOR 3.271,0.719 3.844,1.083 0.573,0.365 10 false PWR 4.896,1.802 5.26,1.979 0.365,0.177 10 false H8 4.552,0.458 4.875,0.844 0.323,0.385 10 false 6 4.563,0.885 4.833,1.177 0.271,0.292 10 false 7 4.563,1.292 5,1.594 0.438,0.302 10 false 1 1.073,0.531 2.385,0.969 1.313,0.438 10 false from IG1 Relay

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the H8 power window regulator master switch assembly connector.


B276330
0.198,1.177 0.615,1.427 0.417,0.25 1.229,0.198 1.406,0.198 1.406,0.198 1.865,1.063 true 2.646,0.26 2.521,0.26 2.521,0.26 2.115,1.042 true 0.5,0.833 0.646,0.833 0.646,0.833 1.021,1.063 true 0.313,1.219 0.646,1.458 0.333,0.24 10 false H8 1.052,0.104 1.344,0.385 0.292,0.281 10 false B 2.74,0.156 3.26,0.542 0.521,0.385 10 false BW 0.135,0.083 0.469,0.385 0.333,0.302 10 false *a 0.333,0.74 0.646,1.031 0.313,0.292 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H8-7 (BW) - Body ground Always 11 to 14 V
H8-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR