Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068699 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Driver Side Power Window Manual Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up/down function does not operate, a malfunction may be present in the power window regulator master switch assembly, front power window regulator motor assembly RH or wire harness.

WIRING DIAGRAM

B276858
4.969,0.792 5.24,1.083 0.271,0.292 10 false U 4.99,3.031 6.583,3.667 1.594,0.635 10 false Power Window Regulator Master Switch Assembly 0.281,0.74 2.198,1.385 1.917,0.646 10 false Front Power Window Regulator Motor Assembly RH 1.188,1.677 2.333,2.042 1.146,0.365 10 false from IG1 Relay 0.625,2.042 1.635,2.375 1.01,0.333 10 false from Battery 3.417,1.854 4.031,2.188 0.615,0.333 10 false PWR 4.969,1.688 5.229,1.948 0.26,0.26 10 false B 4.969,2.052 5.375,2.344 0.406,0.292 10 false BW 4.99,2.438 5.333,2.76 0.344,0.323 10 false E 4.969,1.104 5.24,1.438 0.271,0.333 10 false D 0.281,0.583 0.573,0.885 0.292,0.302 10 false H2 3.396,0.688 3.698,0.99 0.302,0.302 10 false 2 3.396,1 3.75,1.354 0.354,0.354 10 false 1 5,2.865 5.375,3.115 0.375,0.25 10 false H8 4.792,0.708 5.094,1.042 0.302,0.333 10 false 4 4.792,1.01 5.042,1.375 0.25,0.365 10 false 9 4.792,1.594 5.094,1.865 0.302,0.271 10 false 6 4.792,1.958 5.031,2.229 0.24,0.271 10 false 7 4.792,2.333 5.115,2.583 0.323,0.25 10 false 1 3.188,0.792 3.552,1.156 0.365,0.365 10 false U 3.188,1.094 3.49,1.448 0.302,0.354 10 false D 2.563,2.208 3.198,2.563 0.635,0.354 10 false DOOR

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the H8 power window regulator master switch assembly connector.


B276330
0.219,0.896 0.635,1.146 0.417,0.25 1.719,0.323 1.865,1.063 true 2.354,0.354 2.115,1.042 true 0.74,0.469 1.021,1.063 true 0.333,0.948 0.708,1.292 0.375,0.344 10 false H8 1.573,0.156 1.865,0.438 0.292,0.281 10 false B 2.313,0.156 2.833,0.542 0.521,0.385 10 false BW 0.135,0.135 0.469,0.438 0.333,0.302 10 false *a 0.594,0.302 0.906,0.594 0.313,0.292 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H8-7 (BW) - Body ground Always 11 to 14 V
H8-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 Ω



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-1 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Disconnect the H8 power window regulator master switch assembly connector.


b.
B276330
0.219,0.917 0.635,1.167 0.417,0.25 1.177,0.302 1.302,0.302 1.302,0.302 1.573,1.031 true 2.844,1.083 2.49,1.083 true 2.583,0.323 2.438,0.323 2.438,0.323 2.083,1.031 true 0.333,0.958 0.74,1.271 0.406,0.313 10 false H8 0.99,0.219 1.292,0.521 0.302,0.302 10 false U 2.927,0.969 3.229,1.24 0.302,0.271 10 false D 0.188,0.167 0.542,0.531 0.354,0.365 10 false *a 2.677,0.229 2.979,0.5 0.302,0.271 10 false BW
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


Check operation of the front power window regulator motor assembly RH.

OK:
Tester Connection Condition Specified Condition
H8-4 (U) - H8-7 (BW)
H8-9 (D) - Body ground
Always Power window moves up
H8-4 (U) - Body ground
8-7 (BW) - H8-9 (D)
Always Power window moves down



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

3.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
3.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Remove the power window regulator master switch assembly with its connectors still connected.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.
B276285
1.573,1.208 1.573,1.938 true 2.458,1.156 2.865,1.156 true 1.031,1.156 0.635,1.156 true 0.448,1.063 0.688,1.365 0.24,0.302 10 false E 1.542,2 1.708,2.177 0.167,0.177 10 false U 2.948,1.063 3.219,1.323 0.271,0.26 10 false D 0.104,0.094 0.396,0.323 0.292,0.229 10 false *a
*a Component with harness connected
(Power Window Regulator Master Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H8-4 (U) - H8-1 (E) Ignition switch ON, driver side power window switch off → up (manual operation) Below 1 V → 11 to 14 V
Ignition switch ON, driver side power window fully open → driver side power window switch up (auto operation) → driver side power window fully closed Below 1 V → 11 to 14 V → Below 1 V
H8-9 (D) - H8-1 (E) Ignition switch ON, driver side power window switch off → down (manual operation) Below 1 V → 11 to 14 V
Ignition switch ON, driver side power window fully closed → driver side power window switch down (auto operation) → driver side power window fully open Below 1 V → 11 to 14 V → Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the H8 power window regulator master switch assembly connector.


b.

Disconnect the H2 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-9 (D) - H2-1 (D) Always Below 1 Ω
H8-4 (U) - H2-2 (U) Always Below 1 Ω
H8-9 (D) or H2-1 (D) - Body ground Always 10 kΩ or higher
H8-4 (U) or H2-2 (U) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR