Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068699 POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/ Jam Protection Function)  Front Passenger Side Power Window Manual Function does not Operate with Front Passenger Side Power Window Switch  


DESCRIPTION

If the front passenger side manual up/down function does not operate, a malfunction may be present in the front power window regulator motor assembly LH, front power window regulator switch assembly LH, power window regulator master switch assembly or wire harness.

WIRING DIAGRAM

B276859
2.021,3.969 2.396,4.281 0.375,0.313 10 false E 2.021,2.667 2.385,3.042 0.365,0.375 10 false B 2.021,3.031 2.292,3.302 0.271,0.271 10 false U 0.469,4.635 2.073,5.417 1.604,0.781 10 false Power Window Regulator Master Switch Assembly 5.021,3.948 6.958,4.719 1.938,0.771 10 false Front Power Window Regulator Switch Assembly LH 0.375,0.49 2.302,1.188 1.927,0.698 10 false Front Power Window Regulator Motor Assembly LH 0.229,1.615 1.385,2 1.156,0.385 10 false from IG1 Relay 2.365,1.802 2.896,2.115 0.531,0.313 10 false PWR 2.021,3.333 2.271,3.615 0.25,0.281 10 false D 0.385,0.323 1.125,0.521 0.74,0.198 10 false I3 0.479,4.469 0.948,4.698 0.469,0.229 10 false H8 2.208,2.927 2.552,3.156 0.344,0.229 10 false 13 2.219,3.24 2.594,3.542 0.375,0.302 10 false 15 2.24,2.583 2.542,2.917 0.302,0.333 10 false 6 2.229,3.885 2.552,4.177 0.323,0.292 10 false 1 3.469,0.469 3.75,0.729 0.281,0.26 10 false 1 3.479,0.792 3.76,1.115 0.281,0.323 10 false 2 4.865,0.479 5.177,0.792 0.313,0.313 10 false 5 4.865,0.792 5.177,1.083 0.313,0.292 10 false 2 4.865,1.563 5.188,1.854 0.323,0.292 10 false 3 4.854,2.927 5.115,3.24 0.26,0.313 10 false 1 4.865,3.24 5.146,3.5 0.281,0.26 10 false 4 5.031,3.771 5.323,4.01 0.292,0.24 10 false I9 5.063,3.021 5.417,3.271 0.354,0.25 10 false SU 5.063,3.313 5.458,3.646 0.396,0.333 10 false SD 3.281,0.865 3.656,1.24 0.375,0.375 10 false U 3.281,0.563 3.604,0.938 0.323,0.375 10 false D 5.063,0.865 5.344,1.156 0.281,0.292 10 false U 5.063,0.563 5.333,0.885 0.271,0.323 10 false D 5.063,1.635 5.417,1.99 0.354,0.354 10 false B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - BATTERY)
a.

Disconnect the I9 front power window regulator switch assembly LH connector.


b.
B276367
0.271,1.031 0.688,1.281 0.417,0.25 1.708,1.292 2.198,1.833 true 0.073,0.031 0.417,0.344 0.344,0.313 10 false *a 0.417,1.083 0.76,1.354 0.344,0.271 10 false I9 2.323,1.781 2.677,2.073 0.354,0.292 10 false B
*a Front view of wire harness connector
(to Front Power Window Regulator Switch Assembly LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I9-3 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
a.

Remove the front power window regulator switch assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL


b.
B280844
1.885,0.979 2.25,0.563 2.25,0.563 2.5,0.563 true 1.594,0.969 1.26,0.542 1.26,0.542 1.042,0.542 true 2.042,1.031 2.396,1.031 true 1.073,1.031 1.427,1.031 true 1.74,0.969 1.74,0.281 1.74,0.281 1.885,0.281 true 2.448,0.948 2.885,1.26 0.438,0.313 10 false SU 2.563,0.51 2.958,0.792 0.396,0.281 10 false U 1.938,0.198 2.25,0.479 0.313,0.281 10 false B 0.75,0.479 1.083,0.698 0.333,0.219 10 false SD 0.906,0.958 1.125,1.24 0.219,0.281 10 false D

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (D) - 4 (SD)
2 (U) - 3 (B)
UP Below 1 Ω
5 (D) - 4 (SD)
2 (U) - 1 (SU)
OFF Below 1 Ω
5 (D) - 3 (B)
2 (U) - 1 (SU)
DOWN Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

NG

REPLACE FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the I9 front power window regulator switch assembly LH connector.


b.

Disconnect the I3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I9-5 (D) - I3-1 (D) Always Below 1 Ω
I9-2 (U) - I3-2 (U) Always Below 1 Ω
I9-5 (D) or I3-1 (D) - Body ground Always 10 kΩ or higher
I9-2 (U) or I3-2 (U) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Remove the front power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Front Door)>REMOVAL


b.

Apply battery voltage to connector terminals 1 (D) and 2 (U).


c.
B280842
1.156,1.052 1.438,0.188 1.438,0.188 1.635,0.188 true 2.854,1.031 2.854,0.635 2.854,0.635 3.104,0.635 true 2.448,1.031 2.448,0.646 2.448,0.646 2.198,0.646 true 1.74,0.083 2.021,0.333 0.281,0.25 10 false *1 2.031,0.542 2.25,0.76 0.219,0.219 10 false U 3.156,0.563 3.323,0.75 0.167,0.188 10 false D
*1 Motor Gear
V100135

Clockwise
V100136

Counterclockwise


Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (D)
Battery negative (-) → 2 (U)
Motor gear rotates clockwise
Battery positive (+) → 2 (U)
Battery negative (-) → 1 (D)
Motor gear rotates counterclockwise



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)
a.

Disconnect the H8 power window regulator master switch assembly connector.


b.

Disconnect the I9 front power window regulator switch assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H8-13 (U) - I9-1 (SU) Always Below 1 Ω
H8-15 (D) - I9-4 (SD) Always Below 1 Ω
H8-13 (U) or I9-1 (SU) - Body ground Always 10 kΩ or higher
H8-15 (D) or I9-4 (SD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR