If the rear LH side manual up/down function does not operate, a malfunction may be present in the rear power window regulator motor assembly LH, rear power window regulator switch assembly LH, power window regulator master switch assembly or wire harness.
Inspect the fuses for circuits related to this system before performing the following procedure.
Disconnect the J4 rear power window regulator switch assembly LH connector.
| *a | Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly LH) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| J4-3 (B) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear power window regulator switch assembly LH.
Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| 5 (D) - 4 (SD)
2 (U) - 3 (B) |
UP | Below 1 Ω |
| 5 (D) - 4 (SD)
2 (U) - 1 (SU) |
OFF | Below 1 Ω |
| 5 (D) - 3 (B)
2 (U) - 1 (SU) |
DOWN | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the J4 rear power window regulator switch assembly LH connector.
Disconnect the J2 rear power window regulator motor assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| J4-5 (D) - J2-1 (D) | Always | Below 1 Ω |
| J4-2 (U) - J2-2 (U) | Always | Below 1 Ω |
| J4-5 (D) or J2-1 (D) - Body ground | Always | 10 kΩ or higher |
| J4-2 (U) or J2-2 (U) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear power window regulator motor assembly LH.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>REMOVAL
Apply battery voltage to connector terminals 1 (D) and 2 (U).
| *1 | Motor Gear |
|
Clockwise |
|
Counterclockwise |
Check that the motor gear rotates smoothly as follows.
| Measurement Condition | Specified Condition |
|---|---|
| Battery positive (+) → 1 (D)
Battery negative (-) → 2 (U) |
Motor gear rotates clockwise |
| Battery positive (+) → 2 (U)
Battery negative (-) → 1 (D) |
Motor gear rotates counterclockwise |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H8 power window regulator master switch assembly connector.
Disconnect the J4 rear power window regulator switch assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H8-12 (U) - J4-1 (SU) | Always | Below 1 Ω |
| H8-10 (D) - J4-4 (SD) | Always | Below 1 Ω |
| H8-12 (U) or J4-1 (SU) - Body ground | Always | 10 kΩ or higher |
| H8-10 (D) or J4-4 (SD) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG