Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068700 POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)  Remote Up / Down Function does not Operate  


DESCRIPTION

With the ignition switch ON, the power window regulator master switch assembly transmits remote switch signals to the power window regulator switches of the front passenger side power window and rear power windows. Then, each power window regulator switch drives its respective power window regulator motor.

WIRING DIAGRAM

B276856
5.135,0.698 5.385,0.927 0.25,0.229 10 false U 5.156,5.938 6.76,6.385 1.604,0.448 10 false Power Window Regulator Master Switch Assembly 0.406,0.698 2.333,1.188 1.927,0.49 10 false Front Power Window Regulator Switch Assembly RH 0.406,1.969 2.302,2.531 1.896,0.563 10 false Rear Power Window Regulator Switch Assembly LH 1.469,4.198 2.49,4.438 1.021,0.24 10 false from IG1 Relay 3.646,4.385 4.063,4.604 0.417,0.219 10 false PWR 0.406,3.229 2.292,3.76 1.885,0.531 10 false Rear Power Window Regulator Switch Assembly RH 5.135,1.01 5.479,1.302 0.344,0.292 10 false D 5.125,1.927 5.427,2.167 0.302,0.24 10 false U 5.125,2.24 5.385,2.458 0.26,0.219 10 false D 5.125,3.229 5.406,3.448 0.281,0.219 10 false U 5.125,4.208 5.375,4.448 0.25,0.24 10 false B 5.125,5.031 5.302,5.25 0.177,0.219 10 false E 5.135,3.531 5.344,3.76 0.208,0.229 10 false D 0.406,0.531 0.708,0.76 0.302,0.229 10 false H5 0.406,1.802 0.646,2.063 0.24,0.26 10 false J4 0.406,3.052 0.667,3.292 0.26,0.24 10 false J8 3.542,0.604 3.781,0.854 0.24,0.25 10 false 1 3.542,0.927 3.771,1.177 0.229,0.25 10 false 4 4.854,0.604 5.146,0.875 0.292,0.271 10 false 18 4.854,0.927 5.135,1.177 0.281,0.25 10 false 15 4.854,1.833 5.104,2.042 0.25,0.208 10 false 12 4.854,2.146 5.156,2.385 0.302,0.24 10 false 13 4.854,3.135 5.146,3.396 0.292,0.26 10 false 10 4.854,3.448 5.198,3.698 0.344,0.25 10 false 16 3.542,1.833 3.75,2.073 0.208,0.24 10 false 1 3.542,2.146 3.802,2.365 0.26,0.219 10 false 4 3.542,3.125 3.75,3.375 0.208,0.25 10 false 1 3.542,3.448 3.76,3.677 0.219,0.229 10 false 4 5.156,5.771 5.479,6.01 0.323,0.24 10 false I12 4.927,4.115 5.146,4.344 0.219,0.229 10 false 6 4.927,4.927 5.104,5.135 0.177,0.208 10 false 3 3.25,0.688 3.615,1.042 0.365,0.354 10 false SU 3.25,0.99 3.573,1.25 0.323,0.26 10 false SD 3.25,1.927 3.604,2.188 0.354,0.26 10 false SU 3.25,2.25 3.563,2.49 0.313,0.24 10 false SD 3.25,3.219 3.615,3.469 0.365,0.25 10 false SU 3.25,3.531 3.573,3.771 0.323,0.24 10 false SD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Turn the window lock switch off and operate the switches on the power window regulator master switch assembly. Check that the remote up/down function operates normally.

OK:

Remote up/down function operates normally.



Result:
Proceed to
OK
NG



OK

END

NG

2.CHECK MANUAL UP / DOWN FUNCTION
2.CHECK MANUAL UP / DOWN FUNCTION
a.

Check that the front passenger side power window and rear power window manual up/down function operates normally.

OK:

Manual up/down function operates normally.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)

NG

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE

3.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)
a.

Disconnect the I12 power window regulator master switch assembly connector.


b.

Disconnect the H5 front power window regulator switch assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-18 (U) - H5-1 (SU) Always Below 1 Ω
I12-15 (D) - H5-4 (SD) Always Below 1 Ω
I12-18 (U) or H5-1 (SU) - Body ground Always 10 kΩ or higher
I12-15 (D) or H5-4 (SD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)
a.

Disconnect the I12 power window regulator master switch assembly connector.


b.

Disconnect the J4 rear power window regulator switch assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-12 (U) - J4-1 (SU) Always Below 1 Ω
I12-13 (D) - J4-4 (SD) Always Below 1 Ω
I12-12 (U) or J4-1 (SU) - Body ground Always 10 kΩ or higher
I12-13 (D) or J4-4 (SD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)
a.

Disconnect the I12 power window regulator master switch assembly connector.


b.

Disconnect the J8 rear power window regulator switch assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-10 (U) - J8-1 (SU) Always Below 1 Ω
I12-16 (D) - J8-4 (SD) Always Below 1 Ω
I12-10 (U) or J8-1 (SU) - Body ground Always 10 kΩ or higher
I12-16 (D) or J8-4 (SD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR