Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068700 POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)  Driver Side Power Window Manual Function does not Operate with Power Window Master Switch  


DESCRIPTION

If the manual up/down function does not operate, a malfunction may be present in the power window regulator master switch assembly, front power window regulator motor assembly LH or wire harness.

WIRING DIAGRAM

B286740
4.979,0.802 5.177,1.031 0.198,0.229 10 false U 5.01,3.042 6.656,3.563 1.646,0.521 10 false Power Window Regulator Master Switch Assembly 0.313,0.792 2.24,1.271 1.927,0.479 10 false Front Power Window Regulator Motor Assembly RH 1.188,1.698 2.188,1.917 1,0.219 10 false from IG1 Relay 3.417,1.885 3.885,2.146 0.469,0.26 10 false PWR 4.979,1.688 5.156,1.885 0.177,0.198 10 false B 4.979,2.448 5.135,2.646 0.156,0.198 10 false E 4.979,1.104 5.156,1.302 0.177,0.198 10 false D 0.313,0.625 0.594,0.896 0.281,0.271 10 false I3 3.396,0.688 3.573,0.844 0.177,0.156 10 false 2 3.396,1 3.573,1.156 0.177,0.156 10 false 1 5.01,2.875 5.375,3.063 0.365,0.188 10 false I12 4.781,0.688 5.021,0.885 0.24,0.198 10 false 4 4.792,1 5.042,1.219 0.25,0.219 10 false 9 4.781,1.604 5.042,1.833 0.26,0.229 10 false 6 4.781,2.333 5,2.51 0.219,0.177 10 false 3 3.188,0.792 3.385,1.021 0.198,0.229 10 false U 3.188,1.104 3.365,1.302 0.177,0.198 10 false D

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the I12 power window regulator master switch assembly connector.


B276330
0.219,0.896 0.635,1.146 0.417,0.25 2.552,0.26 2.406,0.26 2.406,0.26 1.896,1.031 true 0.917,0.229 1.073,0.229 1.073,0.229 1.385,1.042 true 0.313,0.948 0.688,1.292 0.375,0.344 10 false I12 2.646,0.156 2.938,0.438 0.292,0.281 10 false B 0.135,0.094 0.469,0.396 0.333,0.302 10 false *a 0.719,0.125 1.031,0.417 0.313,0.292 10 false E
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I12-6 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 Ω



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-3 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Disconnect the I12 power window regulator master switch assembly connector.


b.

Using a service wire, connect the terminals according to the table below.


c.
B276330
0.219,0.917 0.635,1.167 0.417,0.25 1.177,0.302 1.302,0.302 1.302,0.302 1.573,1.031 true 2.844,1.083 2.49,1.083 true 2.427,0.313 2.281,0.313 2.281,0.313 1.927,1.021 true 0.313,0.958 0.719,1.271 0.406,0.313 10 false I12 0.99,0.219 1.292,0.521 0.302,0.302 10 false U 2.927,0.969 3.229,1.24 0.302,0.271 10 false D 0.188,0.167 0.542,0.531 0.354,0.365 10 false *a 2.531,0.229 2.833,0.5 0.302,0.271 10 false B
*a Front view of wire harness connector
(to Power Window Regulator Master Switch Assembly)


Check operation of the front power window regulator motor assembly LH.

OK:
Tester Connection Switch Condition Specified Condition
I12-4 (U) - I12-6 (B)
I12-9 (D) - Body ground
Ignition switch ON Power window moves up
I12-4 (U) - Body ground
I12-6 (B) - I12-9 (D)
Ignition switch ON Power window moves down



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

3.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
3.CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
a.

Remove the power window regulator master switch assembly with its connectors still connected.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL


b.
B276285
0.177,1.042 0.594,1.344 0.417,0.302 1.583,1.198 1.583,1.948 true 2.458,1.156 2.865,1.156 true 1.375,1.167 0.865,1.979 0.865,1.979 0.729,1.979 true 0.573,1.896 0.781,2.177 0.208,0.281 10 false E 1.542,2 1.708,2.177 0.167,0.177 10 false U 2.948,1.063 3.219,1.323 0.271,0.26 10 false D 0.104,0.094 0.396,0.323 0.292,0.229 10 false *a 0.292,1.104 0.75,1.302 0.458,0.198 10 false I12
*a Component with harness connected
(Power Window Regulator Master Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
I12-4 (U) - I12-3 (E) Ignition switch ON, driver side power window switch off → up Below 1 V → 11 to 14 V
I12-9 (D) - I12-3 (E) Ignition switch ON, driver side power window switch off → down (manual operation) Below 1 V → 11 to 14 V
Ignition switch ON, driver side power window fully closed → driver side power window switch down (auto operation) → driver side power window fully open Below 1 V → 11 to 14 V → Below 1 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

NG

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the I12 power window regulator master switch assembly connector.


b.

Disconnect the I3 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-9 (D) - I3-1 (D) Always Below 1 Ω
I12-4 (U) - I3-2 (U) Always Below 1 Ω
I12-9 (D) or I3-1 (D) - Body ground Always 10 kΩ or higher
I12-4 (U) or I3-2 (U) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR