Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068700 POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)  Rear Power Window LH Manual Function does not Operate with Rear Power Window Switch LH  


DESCRIPTION

If the rear LH side manual up/down function does not operate, a malfunction may be present in the rear power window regulator motor assembly LH, rear power window regulator switch assembly LH, power window regulator master switch assembly or wire harness.

WIRING DIAGRAM

B276859
2.01,3.969 2.188,4.177 0.177,0.208 10 false E 2.021,2.667 2.198,2.875 0.177,0.208 10 false B 2.01,3.021 2.167,3.229 0.156,0.208 10 false U 0.469,4.667 2.5,5.031 2.031,0.365 10 false Power Window Regulator Master Switch Assembly 1,0.583 2.25,1.219 1.25,0.635 10 false Rear Power Window Regulator Motor Assembly LH 5,3.948 6.979,4.354 1.979,0.406 10 false Rear Power Window Regulator Switch Assembly LH 2.354,1.823 2.729,2.031 0.375,0.208 10 false PWR 0.219,1.635 1.271,1.885 1.052,0.25 10 false from IG1 Relay 2.01,3.323 2.167,3.531 0.156,0.208 10 false D 1.021,0.396 1.25,0.552 0.229,0.156 10 false J2 0.49,4.479 0.833,4.667 0.344,0.188 10 false I12 2.219,2.906 2.438,3.083 0.219,0.177 10 false 12 2.219,3.229 2.448,3.406 0.229,0.177 10 false 13 2.229,2.573 2.375,2.74 0.146,0.167 10 false 6 2.229,3.854 2.365,4.031 0.135,0.177 10 false 3 3.479,0.448 3.646,0.604 0.167,0.156 10 false 1 3.49,0.75 3.656,0.906 0.167,0.156 10 false 2 4.833,0.417 4.969,0.594 0.135,0.177 10 false 5 4.854,0.75 5,0.927 0.146,0.177 10 false 2 4.833,1.5 4.979,1.677 0.146,0.177 10 false 3 4.833,2.917 4.969,3.094 0.135,0.177 10 false 1 4.833,3.24 4.969,3.417 0.135,0.177 10 false 4 5.01,3.781 5.302,4 0.292,0.219 10 false J4 5.042,3.031 5.302,3.198 0.26,0.167 10 false SU 5.042,3.323 5.281,3.5 0.24,0.177 10 false SD 5.063,0.885 5.25,1.083 0.188,0.198 10 false U 5.052,0.573 5.24,0.771 0.188,0.198 10 false D 5.052,1.646 5.219,1.844 0.167,0.198 10 false B 3.271,0.875 3.458,1.073 0.188,0.198 10 false U 3.292,0.542 3.479,0.74 0.188,0.198 10 false D

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - BATTERY)
a.

Disconnect the J4 rear power window regulator switch assembly LH connector.


b.
B276367
0.281,1.031 0.698,1.281 0.417,0.25 1.729,1.26 1.813,1.719 true 0.417,1.073 0.802,1.396 0.385,0.323 10 false J4 0.125,0.146 0.49,0.438 0.365,0.292 10 false *a 1.792,1.76 2.167,2.01 0.375,0.25 10 false B
*a Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly LH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J4-3 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH
a.

Remove the rear power window regulator switch assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL


b.
B280844
1.896,0.99 2.26,0.573 2.26,0.573 2.51,0.573 true 1.573,0.979 1.24,0.552 1.24,0.552 1.021,0.552 true 2.031,1.031 2.385,1.031 true 1.063,1.031 1.417,1.031 true 1.74,0.979 1.74,0.292 1.74,0.292 1.885,0.292 true 2.448,0.948 2.885,1.26 0.438,0.313 10 false SU 2.583,0.5 2.979,0.781 0.396,0.281 10 false U 1.979,0.219 2.292,0.5 0.313,0.281 10 false B 0.75,0.49 1.198,0.802 0.448,0.313 10 false SD 0.875,0.958 1.073,1.219 0.198,0.26 10 false D

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (D) - 4 (SD)
2 (U) - 3 (B)
UP Below 1 Ω
5 (D) - 4 (SD)
2 (U) - 1 (SU)
OFF Below 1 Ω
5 (D) - 3 (B)
2 (U) - 1 (SU)
DOWN Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the J4 rear power window regulator switch assembly LH connector.


b.

Disconnect the J2 rear power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J4-5 (D) - J2-1 (D) Always Below 1 Ω
J4-2 (U) - J2-2 (U) Always Below 1 Ω
J4-5 (D) or J2-1 (D) - Body ground Always 10 kΩ or higher
J4-2 (U) or J2-2 (U) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
a.

Remove the rear power window regulator motor assembly LH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>REMOVAL


b.

Apply battery voltage to connector terminals 1 (D) and 2 (U).


c.
B280846
1.156,1.052 1.448,0.177 1.448,0.177 1.646,0.177 true 2.729,1.125 2.729,0.729 2.729,0.729 2.979,0.729 true 2.531,1.125 2.531,0.729 2.531,0.729 2.292,0.729 true 1.708,0.052 2.083,0.365 0.375,0.313 10 false *1 2.135,0.656 2.5,0.938 0.365,0.281 10 false U 3.063,0.656 3.365,0.958 0.302,0.302 10 false D
*1 Motor Gear
V100135

Clockwise
V100136

Counterclockwise


Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (D)
Battery negative (-) → 2 (U)
Motor gear rotates clockwise
Battery positive (+) → 2 (U)
Battery negative (-) → 1 (D)
Motor gear rotates counterclockwise



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH)
a.

Disconnect the I12 power window regulator master switch assembly connector.


b.

Disconnect the J4 rear power window regulator switch assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-12 (U) - J4-1 (SU) Always Below 1 Ω
I12-13 (D) - J4-4 (SD) Always Below 1 Ω
I12-12 (U) or J4-1 (SU) - Body ground Always 10 kΩ or higher
I12-13 (D) or J4-4 (SD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR