Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)
RM1880E _59 Vehicle Exterior _013248 WINDOW / GLASS _0068700 POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function) J

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM(w/o Jam Protection Function)  Rear Power Window RH Manual Function does not Operate with Rear Power Window Switch RH  


DESCRIPTION

If the rear RH side manual up/down function does not operate, a malfunction may be present in the rear power window regulator motor assembly RH, rear power window regulator switch assembly RH, power window regulator master switch assembly or wire harness.

WIRING DIAGRAM

B276859
2.031,3.969 2.208,4.177 0.177,0.208 10 false E 2.01,2.677 2.188,2.885 0.177,0.208 10 false B 2.01,3.021 2.167,3.229 0.156,0.208 10 false U 0.417,4.667 2,5.188 1.583,0.521 10 false Power Window Regulator Master Switch Assembly 1.052,0.583 2.333,1.219 1.281,0.635 10 false Rear Power Window Regulator Motor Assembly RH 5,3.99 6.875,4.5 1.875,0.51 10 false Rear Power Window Regulator Switch Assembly RH 2.354,1.802 2.729,2 0.375,0.198 10 false PWR 0.24,1.635 1.26,1.865 1.021,0.229 10 false from IG1 Relay 2.021,3.333 2.177,3.542 0.156,0.208 10 false D 1.052,0.354 1.313,0.552 0.26,0.198 10 false J6 0.438,4.448 0.792,4.625 0.354,0.177 10 false I12 2.198,2.906 2.469,3.135 0.271,0.229 10 false 10 2.208,3.229 2.479,3.458 0.271,0.229 10 false 16 2.229,2.583 2.5,2.813 0.271,0.229 10 false 6 2.229,3.854 2.5,4.083 0.271,0.229 10 false 3 3.479,0.469 3.646,0.625 0.167,0.156 10 false 1 3.49,0.75 3.656,0.906 0.167,0.156 10 false 2 4.833,0.417 4.969,0.594 0.135,0.177 10 false 5 4.833,0.75 4.969,0.927 0.135,0.177 10 false 2 4.833,1.5 4.979,1.677 0.146,0.177 10 false 3 4.854,2.906 5,3.083 0.146,0.177 10 false 1 4.854,3.24 5,3.417 0.146,0.177 10 false 4 5.01,3.771 5.302,3.99 0.292,0.219 10 false J8 5.063,3.01 5.323,3.177 0.26,0.167 10 false SU 5.063,3.323 5.344,3.5 0.281,0.177 10 false SD 5.052,0.865 5.219,1.063 0.167,0.198 10 false U 5.052,0.563 5.198,0.76 0.146,0.198 10 false D 5.063,1.656 5.229,1.854 0.167,0.198 10 false B 3.292,0.885 3.479,1.083 0.188,0.198 10 false U 3.281,0.573 3.469,0.771 0.188,0.198 10 false D

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BATTERY)
a.

Disconnect the J8 rear power window regulator switch assembly RH connector.


b.
B276367
0.26,1.042 0.677,1.292 0.417,0.25 1.75,1.271 1.875,1.75 true 0.385,1.083 0.708,1.385 0.323,0.302 10 false J8 0.177,0.156 0.51,0.5 0.333,0.344 10 false *a 1.865,1.792 2.208,2.115 0.344,0.323 10 false B
*a Front view of wire harness connector
(to Rear Power Window Regulator Switch Assembly RH)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
J8-3 (B) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
a.

Remove the rear power window regulator switch assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL


b.
B280844
1.896,0.99 2.26,0.573 2.26,0.573 2.51,0.573 true 1.573,0.979 1.24,0.552 1.24,0.552 1.021,0.552 true 2.031,1.031 2.385,1.031 true 1.063,1.031 1.417,1.031 true 1.74,0.979 1.74,0.292 1.74,0.292 1.885,0.292 true 2.448,0.948 2.885,1.26 0.438,0.313 10 false SU 2.583,0.5 2.979,0.781 0.396,0.281 10 false U 1.979,0.219 2.292,0.5 0.313,0.281 10 false B 0.75,0.49 1.198,0.802 0.448,0.313 10 false SD 0.875,0.958 1.073,1.219 0.198,0.26 10 false D

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (D) - 4 (SD)
2 (U) - 3 (B)
UP Below 1 Ω
5 (D) - 4 (SD)
2 (U) - 1 (SU)
OFF Below 1 Ω
5 (D) - 3 (B)
2 (U) - 1 (SU)
DOWN Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

3.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the J8 rear power window regulator switch assembly RH connector.


b.

Disconnect the J6 rear power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J8-5 (D) - J6-1 (D) Always Below 1 Ω
J8-2 (U) - J6-2 (U) Always Below 1 Ω
J8-5 (D) or J6-1 (D) - Body ground Always 10 kΩ or higher
J8-2 (U) or J6-2 (U) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
a.

Remove the rear power window regulator motor assembly RH.

Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR(for Rear Door)>REMOVAL


b.

Apply battery voltage to connector terminals 1 (D) and 2 (U).


c.
B280845
1.146,1.052 1.438,0.177 1.438,0.177 1.635,0.177 true 2.729,1.052 2.729,0.667 2.729,0.667 2.979,0.667 true 2.531,1.052 2.531,0.667 2.531,0.667 2.292,0.667 true 1.719,0.073 2.094,0.375 0.375,0.302 10 false *1 2.146,0.583 2.5,0.896 0.354,0.313 10 false U 3.052,0.594 3.271,0.938 0.219,0.344 10 false D
*1 Motor Gear
V100135

Clockwise
V100136

Counterclockwise


Check that the motor gear rotates smoothly as follows.

OK:
Measurement Condition Specified Condition
Battery positive (+) → 1 (D)
Battery negative (-) → 2 (U)
Motor gear rotates counterclockwise
Battery positive (+) → 2 (U)
Battery negative (-) → 1 (D)
Motor gear rotates clockwise



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)

NG

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

5.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY - REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH)
a.

Disconnect the I12 power window regulator master switch assembly connector.


b.

Disconnect the J8 rear power window regulator switch assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I12-10 (U) - J8-1 (SU) Always Below 1 Ω
I12-16 (D) - J8-4 (SD) Always Below 1 Ω
I12-10 (U) or J8-1 (SU) - Body ground Always 10 kΩ or higher
I12-16 (D) or J8-4 (SD) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR