Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
| *1 | Centering Bolt |
| *2 | Standard Bolt |
Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.
A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).
1.INSPECT FRONT DOOR PANEL SUB-ASSEMBLY LH
Check that the clearance measurements of areas A to AB are within the standard ranges.
| Area | Specified Condition | Area | Specified Condition |
|---|---|---|---|
| A | 4.8 to 7.8 mm (0189 to 0.307 in.) | B | 1.0 to 4.0 mm (0.0394 to 0.157 in.) |
| C | 2.7 to 5.7 mm (0.106 to 0.224 in.) | D | 7.4 to 10.4 mm (0.291 to 0.409 in.) |
| E | 2.4 to 5.4 mm (0.0945 to 0.213 in.) | F | 8.1 to 11.1 mm (0.319 to 0.437 in.) |
| G | 1.8 to 4.8 mm (0.0709 to 0.189 in.) | H | 5.0 to 8.0 mm (0.197 to 0.315 in.) |
| I | 3.7 to 6.7 mm (0.146 to 0.264 in.) | J | 3.9 to 6.9 mm (0.154 to 0.272 in.) |
| K | 3.7 to 6.7 mm (0.146 to 0.264 in.) | L | -1.2 to 1.8 mm (-0.0472 to 0.0709 in.) |
| M | 3.7 to 6.7 mm (0.146 to 0.264 in.) | N | -1.3 to 1.7 mm (-0.0512 to 0.0669 in.) |
| O | 6.1 to 9.1 mm (0.240 to 0.358 in.) | P | 7.0 to 10.0 mm (0.276 to 0.394 in.) |
| Q | 5.8 to 8.8 mm (0.228 to 0.346 in.) | R | 6.9 to 9.9 mm (0.272 to 0.390 in.) |
| S | 5.1 to 8.1 mm (0.201 to 0.319 in.) | T | 6.4 to 9.4 mm (0.252 to 0.370 in.) |
| U | 3.4 to 6.4 mm (0.134 to 0.252 in.) | V | -1.4 to 1.6 mm (-0.0551 to 0.0630 in.) |
| W | 3.2 to 6.2 mm (0.126 to 0.244 in.) | X | -1.4 to 1.6 mm (-0.0551 to 0.0630 in.) |
| Y | 2.7 to 5.7 mm (0.106 to 0.224 in.) | Z | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
| AA | 2.5 to 5.5 mm (0.0984 to 0.217 in.) | AB | -1.5 to 1.5 mm (-0.0591 to 0.0591 in.) |
2.ADJUST FRONT DOOR PANEL SUB-ASSEMBLY LH
Using SST, loosen the hinge bolts on the body and adjust the door position.
Tighten the hinge bolts on the body after the adjustment.
Loosen the hinge bolts on the door and adjust the door position.
Tighten the hinge bolts on the door after the adjustment.
Using a T30 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.
Using a T30 "TORX" socket, tighten the striker mounting screws after the adjustment.