Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR
RM1880E _59 Vehicle Exterior _013249 DOOR / HATCH _0068715 REAR DOOR N

DOOR / HATCH  REAR DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·
B276679
0.656,1.75 1.063,1.99 0.406,0.24 10 false *1 2.563,1.75 2.865,1.99 0.302,0.24 10 false *2
*1 Centering Bolt
*2 Standard Bolt


Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSPECT REAR DOOR PANEL SUB-ASSEMBLY LH

a.

Check that the clearance measurements of areas A to U are within the standard ranges.

B280445
2.531,0.229 2.854,0.479 0.323,0.25 10 false A 2.552,0.656 2.906,0.948 0.354,0.292 10 false B 3.542,0.208 3.76,0.385 0.219,0.177 10 false C 3.448,0.573 3.667,0.74 0.219,0.167 10 false D 4.76,0.177 5,0.385 0.24,0.208 10 false E 4.708,0.594 4.938,0.781 0.229,0.188 10 false F 6.021,0.708 6.281,0.896 0.26,0.188 10 false G 6.26,0.604 6.438,0.781 0.177,0.177 10 false H 6.125,1.792 6.302,1.948 0.177,0.156 10 false I 5.865,2.938 6.094,3.115 0.229,0.177 10 false J 5.177,3.813 5.406,3.969 0.229,0.156 10 false K 3.406,4.24 3.583,4.396 0.177,0.156 10 false L 3.885,4.49 4.115,4.667 0.229,0.177 10 false M 2.365,4.229 2.583,4.406 0.219,0.177 10 false N 2.885,4.49 3.104,4.677 0.219,0.188 10 false O 1.479,3.625 1.656,3.781 0.177,0.156 10 false P 1.042,3.885 1.281,4.073 0.24,0.188 10 false Q 1.281,2.542 1.531,2.729 0.25,0.188 10 false R 0.99,2.729 1.25,2.969 0.26,0.24 10 false S 1.281,1.635 1.542,1.833 0.26,0.198 10 false T 1.5,0.469 1.865,0.813 0.365,0.344 10 false U

Standard:
Area Specified Condition Area Specified Condition
A 3.1 to 6.1 mm (0.122 to 0.240 in.) B 5.0 to 8.0 mm (0.197 to 0.315 in.)
C 2.8 to 5.8 mm (0.110 to 0.228 in.) D 6.5 to 9.5 mm (0.256 to 0.374 in.)
E 2.2 to 5.2 mm (0.0866 to 0.205 in.) F 6.6 to 9.6 mm (0.260 to 0.378 in.)
G 12.6 to 15.6 mm (0.496 to 0.614 in.) H -1.2 to 1.8 mm (-0.0472 to 0.0709 in.)
I 3.2 to 6.2 mm (0.126 to 0.244 in.) J 3.5 to 6.5 mm (0.138 to 0.256 in.)
K 4.3 to 7.3 mm (0.169 to 0.287 in.) L 6.0 to 9.0 mm (0.236 to 0.354 in.)
M 7.1 to 10.1 mm (0.280 to 0.398 in.) N 5.2 to 8.2 mm (0.205 to 0.323 in.)
O 6.6 to 9.6 mm (0.260 to 0.378 in.) P 3.7 to 6.7 mm (0.146 to 0.264 in.)
Q -1.3 to 1.7 mm (-0.0512 to 0.0669 in.) R 3.7 to 6.7 mm (0.146 to 0.264 in.)
S -1.2 to 1.8 mm (-0.0472 to 0.0709 in.) T 3.9 to 6.9 mm (0.154 to 0.272 in.)
U 3.7 to 6.7 mm (0.146 to 0.264 in.) - -



Hide 2.ADJUST REAR DOOR PANEL SUB-ASSEMBLY LH

a.
B280451

Loosen the hinge bolts on the body and adjust the door position.


b.

Tighten the hinge bolts on the body after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


c.
B280452

Loosen the hinge bolts on the door and adjust the door position.


d.

Tighten the hinge bolts on the door after the adjustment.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


e.
B280453

Using a T30 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


f.

Using a T30 "TORX" socket, tighten the striker mounting screws after the adjustment.

Torque:
23 N*m (235 kgf*cm, 17 ft.*lbf)