Home › Vehicle Exterior › DOOR / HATCH › BACK DOOR
RM1880E _59 Vehicle Exterior _013249 DOOR / HATCH _0068719 BACK DOOR N

DOOR / HATCH  BACK DOOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·
B276679
0.656,1.75 1.063,1.99 0.406,0.24 10 false *1 2.563,1.75 2.865,1.99 0.302,0.24 10 false *2
*1 Centering Bolt
*2 Standard Bolt


Centering bolts are used to mount the door hinge to the vehicle body and door. The door cannot be adjusted with the centering bolts on. Substitute the centering bolts for standard bolts when making adjustments.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 1.INSPECT BACK DOOR PANEL SUB-ASSEMBLY

a.

Check that the clearance measurements of areas A to K are within the standard ranges.

B280446
2.01,0.302 2.25,0.479 0.24,0.177 10 false A 1.615,0.573 1.844,0.74 0.229,0.167 10 false B 4.063,0.333 4.365,0.563 0.302,0.229 10 false C 3.5,0.604 3.771,0.792 0.271,0.188 10 false D 5.813,1.552 6.052,1.76 0.24,0.208 10 false E 5.448,2.875 5.625,3.031 0.177,0.156 10 false F 5.74,2.594 6.01,2.802 0.271,0.208 10 false G 5.188,3.906 5.417,4.083 0.229,0.177 10 false H 5.542,3.698 5.719,3.854 0.177,0.156 10 false I 3.552,4.229 3.792,4.396 0.24,0.167 10 false J 2.083,4.146 2.438,4.344 0.354,0.198 10 false K

Standard:
Area Specified Condition Area Specified Condition
A 8.1 mm (0.319 in.) B 0.1 mm (0.00394 in.)
C 8.0 mm (0.315 in.) D 1.0 mm (0.0394 in.)
E 5.5 mm (0.217 in.) F (Reference) 5.7 mm (0.224 in.)
G (Reference) 1.1 mm (0.0433 in.) H (Reference) 5.6 mm (0.220 in.)
I (Reference) 1.5 mm (0.0591 in.) J 9.4 mm (0.370 in.)
K 9.0 mm (0.354 in.) - -



Hide 2.ADJUST BACK DOOR PANEL SUB-ASSEMBLY

a.
B280454

Loosen the hinge bolts on the body.


b.

Adjust the back door panel by moving it up and down and left and right so that the clearance measurements are within the specified ranges.


c.

Tighten the hinge bolts.

Torque:
19 N*m (194 kgf*cm, 13 ft.*lbf)


d.
B280455

Adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.


e.

Tighten the striker mounting screws after the adjustment.

Torque:
18 N*m (178 kgf*cm, 13 ft.*lbf)