Home › Vehicle Exterior › WIPER / WASHER › FRONT WIPER MOTOR
RM1880E _59 Vehicle Exterior _013251 WIPER / WASHER _0068726 FRONT WIPER MOTOR G

WIPER / WASHER  FRONT WIPER MOTOR  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT WINDSHIELD WIPER LINK ASSEMBLY (for LHD)

a.
E226512
2.688,0 2.938,0.365 0.25,0.365 10 false A 2.448,1.802 2.677,2.042 0.229,0.24 10 false B

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

Standard:
Area Standard Condition
A 25 mm ( 0.984 in.)
B 40 mm ( 1.57 in.)



b.

Stop the front wiper motor and link assembly operation.


c.
E226514
0.865,1.906 0.865,2.188 false 2.365,4.208 2.365,4.448 false 0.073,0.094 0.458,0.688 0.385,0.594 10 false *A 0.073,2.333 0.385,2.656 0.313,0.323 10 false *B 2.323,4.479 2.698,4.646 0.375,0.167 10 false *1 0.781,2.208 1.073,2.458 0.292,0.25 10 false *1 1.094,2.229 1.354,2.469 0.26,0.24 10 false A 2.771,2.104 2.979,2.396 0.208,0.292 10 false B 1.521,4.479 1.844,4.667 0.323,0.188 10 false D 0.25,4.281 0.469,4.458 0.219,0.177 10 false C
*A for RH Side
*B for LH Side
*1 Louver Edge


Check the automatic stop position.

OK:

The front wipers stop at the positions shown in the illustration.


Standard:
Area Standard Condition
A 30 mm ( 1.18 in.)
B 32 mm ( 1.26 in.)
C 30 mm ( 1.18 in.)
D 32 mm ( 1.26 in.)


If the result is not as specified, remove and reinstall the wiper arm and blade assembly, and perform the on-vehicle inspection described above to inspect the wiper motor and link assembly again.

If the result is not as specified again, inspect the wiper motor and link assembly with it removed from the vehicle body (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).


Hide 2.REMOVE WINDSHIELD WIPER LINK ASSEMBLY (for RHD)

a.
E226513
1.167,0.042 1.51,0.406 0.344,0.365 10 false A 0.906,1.802 1.229,2 0.323,0.198 10 false B

Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and the wipers do not come into contact with the vehicle body.

Standard:
Area Standard Condition
A 25 mm ( 0.984 in.)
B 40 mm ( 1.57 in.)



b.

Stop the front wiper motor and link assembly operation.


c.
E226515
2.688,1.875 2.688,2.135 false 1.156,4.219 1.156,4.427 false 0.063,0.135 0.417,0.385 0.354,0.25 10 false *A 0.073,2.427 0.583,2.719 0.51,0.292 10 false *B 2.635,2.167 2.917,2.479 0.281,0.313 10 false *1 1.104,4.458 1.344,4.646 0.24,0.188 10 false *1 2.26,2.229 2.469,2.469 0.208,0.24 10 false A 0.573,2.104 0.74,2.313 0.167,0.208 10 false B 3.052,4.292 3.271,4.51 0.219,0.219 10 false *C 1.688,4.406 2.01,4.604 0.323,0.198 10 false *D
*A for RH Side
*B for LH Side
*1 Louver Edge


Check the automatic stop position.

OK:

The front wipers stop at the positions shown in the illustration.


Standard:
Area Standard Condition
A 30 mm ( 1.18 in.)
B 32 mm ( 1.26 in.)
C 30 mm ( 1.18 in.)
D 32 mm ( 1.26 in.)


If the result is not as specified, remove and reinstall the wiper arm and blade assembly, and perform the on-vehicle inspection described above to inspect the wiper motor and link assembly again.

If the result is not as specified again, inspect the wiper motor and link assembly with it removed from the vehicle body (See page Vehicle Exterior>WIPER / WASHER>FRONT WIPER MOTOR>REMOVAL).