Home › Vehicle Exterior › WIPER / WASHER › REAR WIPER RUBBER
RM1880E _59 Vehicle Exterior _013251 WIPER / WASHER _0068729 REAR WIPER RUBBER A

WIPER / WASHER  REAR WIPER RUBBER  REPLACEMENT  


PROCEDURE

Hide 1.REMOVE REAR WIPER BLADE ASSEMBLY

a.
E226563

Raise the wiper arm, and then detach the claw by rotating the wiper blade to the position where a "click" sound" is heard as shown in the illustration.

NOTICE:

Be careful not to damage the claw.



b.
E226564

Pull the wiper blade straight toward the left side of the vehicle to remove it from the wiper arm.

NOTICE:

Do not fold the wiper arm with the wiper blade removed. The arm tip may damage the back door glass surface.



Hide 2.REMOVE REAR WIPER RUBBER

a.
E178053
0.875,1.563 1.302,1.917 0.427,0.354 10 false *a 1.896,0.052 2.229,0.292 0.333,0.24 10 false *b 2.781,1.667 3.156,1.99 0.375,0.323 10 false *d 2.698,1.01 3.083,1.375 0.385,0.365 10 false *c
*a Stopper (Rear End of Blade)
*b Lightly Push (Grip)
*c Lift
*d Pull


Lift and pull the end of the wiper rubber protruding from the blade stopper as shown in the illustration to remove the wiper rubber.

NOTICE:

Do not forcibly pull out the wiper rubber. The backing plates will be deformed or the blade claws will be damaged.


HINT:

Lightly pushing the rubber between the end and middle allows it to be removed more easily.



b.

Remove the 2 wiper rubber backing plates from the wiper rubber.


Hide 3.INSTALL REAR WIPER RUBBER

a.
E178054
0.677,0.24 0.438,0.24 0.438,0.24 0.438,1.833 false 1.708,2.76 1.708,2.188 false 0.781,0.167 1.094,0.427 0.313,0.26 10 false *1 1.646,2.833 2.021,3.177 0.375,0.344 10 false *1 1.406,0.688 1.781,1.031 0.375,0.344 10 false *a
*1 Backing Plate
*a Curved


Install the 2 backing plates as shown in the illustration.

NOTICE:

Install the backing plates so that they are facing in the correct direction.



b.
E178055
2.323,1.521 2.396,1.521 2.396,1.521 2.573,1.229 true 2.542,1.875 2.688,1.875 2.688,1.875 2.688,1.333 true 2.188,0.531 1.698,0.177 1.698,0.177 1.479,0.177 true 1.292,0.104 1.646,0.427 0.354,0.323 10 false *a 2.125,1.448 2.51,1.823 0.385,0.375 10 false *b 2.344,1.792 2.688,2.115 0.344,0.323 10 false *c
*a Second Claw
*b Rear End Claw
*c Rear End Stopper


Insert the wiper rubber into the front end of the wiper blade and slide it towards the rear end through the second claw.


c.

After pushing the wiper rubber through the rear end claw, allow it to pass over the rear end stopper.


d.
E178056
1.24,0.208 1.385,0.208 1.385,0.208 1.625,0.531 true 1.063,0.146 1.51,0.552 0.448,0.406 10 *1
*1 Front End Claw


Slide the wiper rubber through the front end claw.


Hide 4.INSTALL REAR WIPER BLADE ASSEMBLY

a.
E226565

Push the wiper blade straight toward the right side of the vehicle to attach the claw and install the wiper blade to the wiper arm.

NOTICE:

Be careful not to damage the claw.



b.

Close the wiper blade holder.