Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT ASSEMBLY
RM1880E _59 Vehicle Exterior _013252 LIGHTING (EXT) _0068736 HEADLIGHT ASSEMBLY N

LIGHTING (EXT)  HEADLIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. VEHICLE PREPARATION FOR HEADLIGHT AIM ADJUSTMENT

a.

Prepare the vehicle:

·

Make sure that there is no damage or deformation of the body around the headlights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, making sure that the spare tire, tools and jack are in their original positions.

·

Have a person of average weight (75 kg, 165 lb) sit in the driver seat.

·
E107873

Set the headlight leveling switch dial to 0.



Hide 2. PREPARATION FOR HEADLIGHT AIMING (Using a screen)

a.
E227292
1.063,1.875 1.448,2.115 0.385,0.24 10 false *a
*a 25 m or 3 m


Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the hot area. The cutoff line is a distinct line, below which light from the headlights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 25 m (82 ft.) distance between the vehicle (headlight bulb center) and wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.


NOTICE:

A distance of 25 m (82.0 ft.) between the vehicle and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.8 ft.). View the part of the illustration applicable to the distance from the vehicle to the wall.



b.

Prepare a piece of thick white paper that is approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

E227293
0.802,0.083 3.01,0.406 2.208,0.323 12 false Aligning distance is 25 m: 4.375,0.073 6.417,0.469 2.042,0.396 12 false Aligning distance is 3 m: 4.646,0.74 5.396,1.073 0.75,0.333 10 false V RH Line 1.188,0.75 1.865,0.99 0.677,0.24 10 false V RH Line 1.198,1.771 1.875,2.125 0.677,0.354 10 false V LH Line 4.677,1.781 5.438,2.063 0.76,0.281 10 false V LH Line 3.146,1.333 3.667,1.646 0.521,0.313 10 false V Line 6.583,1.333 7.083,1.667 0.5,0.333 10 false V Line 4.875,4.167 5.708,4.458 0.833,0.292 10 false 3 m 1.354,4.177 2.323,4.479 0.969,0.302 10 false 25 m 0.219,3.438 0.802,3.813 0.583,0.375 10 false H Line 3.677,3.427 4.208,3.635 0.531,0.208 10 false H Line 4.594,3.667 5.052,3.969 0.458,0.302 10 false 90° 4.646,1.135 5.052,1.438 0.406,0.302 10 false 90° 1.198,1.146 1.521,1.406 0.323,0.26 10 false 90° 1.208,3.698 1.625,3.969 0.417,0.271 10 false 90°

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
I033423
0.365,1.698 0.792,2.073 0.427,0.375 10 *e 2.792,0.875 3.188,1.271 0.396,0.396 10 *d 1.604,0.333 2.021,0.698 0.417,0.365 10 *b 1,0.333 1.385,0.698 0.385,0.365 10 *a 2.26,0.313 2.646,0.708 0.385,0.396 10 *c
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground


Draw base lines (H, V LH and V RH lines) on the screen as shown in the illustration.

HINT:
·

The base lines differ for ''low beam inspection'' and ''high beam inspection''.

·

Mark the headlight bulb center marks on the screen. If the center mark cannot be observed on the headlight, use the center of the headlight bulb or the manufacturer's name marked on the headlight as the center mark.



i.

H line (headlight height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the headlight bulb center marks of the low beam headlights.


ii.

V LH Line, V RH Line (center mark position of the left-hand (LH) and right-hand (RH) headlights):

Draw two vertical lines so that they intersect the H line at each center mark (aligned with the center of the low beam headlight bulbs).



Hide 3.INSPECT HEADLIGHT AIMING

a.
E227292
1.063,1.875 1.448,2.115 0.385,0.24 10 false *a
*a 25 m or 3 m


Cover the headlight or disconnect the connector of the headlight on the opposite side to prevent light from the headlight that is not being inspected from affecting the headlight aiming.

NOTICE:

Do not keep the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin, which may melt or be damaged due to excessive heat.


HINT:

When checking the aim of the high beam headlight, cover the low beam headlight or disconnect the connector.



b.

Start the engine.


c.

Turn on the headlights and make sure that the cutoff line is within the specified area shown in the illustration.

E227800
2.49,0.896 2.219,0.896 false 2.219,0.896 1.833,1.688 false 5.677,0.896 5.406,0.896 false 5.406,0.896 5.021,1.677 false 0.677,0.042 3.354,0.354 2.677,0.313 12 false Aligning distance is 25 m: 3.625,0.042 6.49,0.365 2.865,0.323 12 false Aligning distance is 3 m: 1.188,0.292 1.896,0.646 0.708,0.354 10 false V LH Line 0.969,0.813 1.625,1.188 0.656,0.375 10 false 83 mm 2.688,1.333 3.417,1.74 0.729,0.406 10 false H Line 0.604,1.979 1.323,2.365 0.719,0.385 10 false 249 mm 2.125,1.979 2.771,2.354 0.646,0.375 10 false 375 mm 3.313,0.5 4.354,0.802 1.042,0.302 10 false Low Beam 6.01,1.333 6.833,1.75 0.823,0.417 10 false H Line 4.177,0.813 4.802,1.188 0.625,0.375 10 false 10 mm 5.448,1.979 6.063,2.354 0.615,0.375 10 false 45 mm 3.656,1.979 4.292,2.354 0.635,0.375 10 false 30 mm 0.052,0.5 1.208,0.885 1.156,0.385 10 false Low Beam 3.313,2.448 4.344,2.833 1.031,0.385 10 false High Beam 0.104,2.448 1.5,2.854 1.396,0.406 10 false High Beam 2.792,3.521 3.573,4.063 0.781,0.542 10 false H Line 5.958,3.521 6.854,4.25 0.896,0.729 10 false H Line 2.281,4 2.917,4.375 0.635,0.375 10 false 37 mm 5.479,4 6.146,4.375 0.667,0.375 10 false 4 mm 1.917,0.292 2.906,0.688 0.99,0.396 10 false V RH Line 4.302,0.292 5.01,0.646 0.708,0.354 10 false V LH Line 5.052,0.292 5.76,0.646 0.708,0.354 10 false V RH Line 1.01,2.708 2.021,3.24 1.01,0.531 10 false V LH Line 1.76,2.708 2.469,3.063 0.708,0.354 10 false V RH Line 4.167,2.708 5.458,3.375 1.292,0.667 10 false V LH Line 4.927,2.708 5.948,3.156 1.021,0.448 10 false V RH Line 2.542,0.813 3.365,1.188 0.823,0.375 10 false Point A 5.719,0.813 6.656,1.24 0.938,0.427 10 false Point A

HINT:
·

Since the low beam light and high beam light are a unit, if the aim on one is correct, the other should also be correct. However, check both beams just to make sure.

·

If the alignment distance is 25 m (82 ft.):

The low beam cutoff line should be between 83 mm (3.27 in.) and 375 mm (14.8 in.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The low beam cutoff line should be between 10 mm (0.393 in.) and 45 mm (1.77 in.) below the H line.

·

If the alignment distance is 25 m (82 ft.):

The horizontal line of the preferred low beam cutoff line is 249 mm (9.80 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The horizontal line of the preferred low beam cutoff line is 30 mm (1.18 in.) below the H line and point A of the preferred low beam cutoff line is on the V LH or V RH line.

·

If the alignment distance is 25 m (82 ft.):

The preferred high beam center of intensity is 37 mm (1.45 in.) below the H line and is on the V LH or V RH line.

·

If the alignment distance is 3 m (9.84 ft.):

The preferred high beam center of intensity is 4 mm (0.157 in.) below the H line and is on the V LH or V RH line.




Hide 4.ADJUST HEADLIGHT AIMING

a.
E229570
0.552,0.813 1.01,1.583 true 1.885,2.208 2.865,1.719 true 1.281,0.865 1.479,1.031 false 2.552,1.094 2.125,1.51 true 0.354,0.719 0.646,0.969 0.292,0.25 10 false *1 2.958,1.635 3.313,1.833 0.354,0.198 10 false *2 2.635,0.99 2.99,1.167 0.354,0.177 10 false *3 1.073,0.729 1.385,0.938 0.313,0.208 10 false *3
*1 Horizontal Aiming Screw
*2 Vertical Aiming Screw
*3 Screwdriver


Using a screwdriver, adjust the aim.

Adjust the aim of each headlight to the specified range by turning each aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it, and then retighten it so that the final turn of the screw is in the clockwise direction.


HINT:
·

The low beam and high beam headlight are a unit. Adjusting the aim on the low beam to the correct position should also result in the high beam adjustment being correct.

·

If it is not possible to correctly adjust headlight aim, check the bulb, headlight unit and headlight unit reflector installation.

·

The headlight aim moves up when turning the vertical aiming screw clockwise, and moves down when turning the vertical aiming screw counterclockwise. The headlight aim moves left when turning the horizontal aiming screw clockwise, and moves right when turning the horizontal aiming screw counterclockwise.