Home › Vehicle Exterior › LIGHTING (EXT) › FOG LIGHT ASSEMBLY
RM1880E _59 Vehicle Exterior _013252 LIGHTING (EXT) _0068737 FOG LIGHT ASSEMBLY N

LIGHTING (EXT)  FOG LIGHT ASSEMBLY  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

If there is a problem with the fog light aim, the cause of the problem may be an incorrectly installed bulb. Therefore, bulb installation should be checked prior to performing the adjustment procedure.



PROCEDURE

Hide 1.VEHICLE PREPARATION FOR FOG LIGHT AIMING ADJUSTMENT

a.

Prepare the vehicle:

·

Make sure that there is no damage or deformation of the body around the fog lights.

·

Fill the fuel tank.

·

Make sure that the oil is filled to the specified level.

·

Make sure that the coolant is filled to the specified level.

·

Inflate the tires to the appropriate pressure.

·

Unload the trunk and vehicle, making sure that the spare tire, tools and jack are in their original positions.

·

Have a person of average weight (75 kg, 165 lb) sit in the driver seat.



Hide 2.PREPARATION FOR FOG LIGHT AIMING (Using a screen)

a.
E227301
1.052,1.885 1.5,2.104 0.448,0.219 10 false *a
*a 25 m or 3 m


Prepare the vehicle:

·

Place the vehicle in a location that is dark enough to clearly observe the cutoff line. The cutoff line is a distinct line, below which light from the fog lights can be observed and above which it cannot.

·

Place the vehicle at a 90° angle to the wall.

·

Create a 25 m (82.0 ft.) distance between the vehicle (fog light bulb center) and the wall.

·

Make sure that the vehicle is on a level surface.

·

Bounce the vehicle up and down to settle the suspension.

NOTICE:

A distance of 25 m (82.0 ft.) between the vehicle and the wall is necessary for proper aim adjustment. If unavailable, secure a distance of exactly 3 m (9.84 ft.). View the part of the illustration below applicable to the distance from the vehicle to the wall.




b.

Prepare a piece of thick white paper that is approximately 2 m (6.56 ft.) (height) x 4 m (13.1 ft.) (width) to use as a screen.


c.

Draw a vertical line down the center of the screen (V line).


d.

Set the screen as shown in the illustration.

E227302
0.885,0.104 3.198,0.521 2.313,0.417 12 false Aligning distance is 25 m: 1.26,1.198 1.75,1.521 0.49,0.323 10 false 90° 1.229,0.823 2.021,1.094 0.792,0.271 10 false V RH Line 1.219,1.75 2.271,2.25 1.052,0.5 10 false V LH Line 1.219,3.729 1.656,4.052 0.438,0.323 10 false 90° 1.365,4.146 2.406,4.448 1.042,0.302 10 false 25 m 4.5,0.813 5.323,1.083 0.823,0.271 10 false V RH Line 4.5,1.75 5.375,2.083 0.875,0.333 10 false V LH Line 4.646,1.198 5.198,1.427 0.552,0.229 10 false 90° 3.177,1.281 3.646,1.479 0.469,0.198 10 false V Line 6.604,1.281 7.104,1.573 0.5,0.292 10 false V Line 4.135,0.104 6.271,0.51 2.135,0.406 12 false Aligning distance is 3 m: 4.667,3.719 5.021,3.875 0.354,0.156 10 false 90° 3.635,3.563 4.177,3.823 0.542,0.26 10 false H Line 0.198,3.573 0.823,3.875 0.625,0.302 10 false H Line 4.833,4.135 5.615,4.333 0.781,0.198 10 false 3 m

HINT:
·

Stand the screen perpendicular to the ground.

·

Align the V line on the screen with the center of the vehicle.




e.
I033423
0.365,1.698 0.792,2.073 0.427,0.375 10 *e 2.792,0.875 3.188,1.271 0.396,0.396 10 *d 1.604,0.333 2.021,0.698 0.417,0.365 10 *b 1,0.333 1.385,0.698 0.385,0.365 10 *a 2.26,0.313 2.646,0.708 0.385,0.396 10 *c
*a V LH Line
*b V Line
*c V RH Line
*d H Line
*e Ground


Draw base lines (H, V LH and V RH lines) on the screen as shown in the illustration.

HINT:

Mark the fog light bulb center marks on the screen. If the center mark cannot be observed on the fog light, use the center of the fog light bulb or the manufacturer's name marked on the fog light as the center mark.


i.

H Line (fog light height):

Draw a horizontal line across the screen so that it passes through the center marks. The H line should be at the same height as the fog light bulb center marks of the fog lights.


ii.

V LH Line, V RH Line (center mark position of left-hand (LH) and right-hand (RH) fog lights):

Draw two vertical lines so that they intersect the H line at each center mark.



Hide 3.INSPECT FOG LIGHT AIMING

a.

Cover the fog light or disconnect the connector of the fog light on the opposite side to prevent light from the fog light that is not being inspected from affecting the fog light aiming inspection.

NOTICE:

Do not keep the fog light covered for more than 3 minutes. The fog light lens is made of synthetic resin, which may melt or be damaged due to excessive heat.



b.

Start the engine.


c.

Turn on the fog lights and make sure that the cutoff line is within the specified area shown in the illustration.

B117629
1.49,0.938 2.354,1.219 0.865,0.281 10 false V RH Line 1.49,0.646 2.406,0.917 0.917,0.271 10 false V LH Line 2.729,1.76 3.292,2.125 0.563,0.365 10 false 375 mm 0.25,1.323 0.917,1.604 0.667,0.281 10 false H Line 3.615,1.313 4.719,1.698 1.104,0.385 10 false H Line 4.844,0.927 5.792,1.24 0.948,0.313 10 false V RH Line 4.844,0.635 5.917,1.01 1.073,0.375 10 false V LH Line 6.063,1.76 6.625,2.125 0.563,0.365 10 false 45 mm 0.906,0.167 3.156,0.51 2.25,0.344 12 false Aligning distance is 25 m: 4.469,0.156 6.49,0.458 2.021,0.302 12 false Aligning distance is 3 m:

HINT:
·

If the alignment distance is 25 m (82 ft.):

The upper edge of the hot zone for the fog light should be 375 mm (14.8 in.) below the H line.

·

If the alignment distance is 3 m (9.84 ft.):

The upper edge of the hot zone for the fog light should be 45 mm (1.77 in.) below the H line.




Hide 4.ADJUST FOG LIGHT AIMING

a.
E227831
2.208,1.479 1.833,1.229 false 2.271,1.417 2.708,1.646 0.438,0.229 10 false *1
*1 Aiming Screw


Adjust the fog light aim so that it is within the specified range by turning the aiming screw with a screwdriver.

NOTICE:

The final turn of the aiming screw should be made in the clockwise direction. If the screw is tightened excessively, loosen it, and then retighten it so that the final turn of the screw is in the clockwise direction.


HINT:

If it is not possible to correctly adjust fog light aim, check the bulb, fog light unit and fog light unit reflector installation.