Home › Vehicle Exterior › LIGHTING (EXT) › HEADLIGHT DIMMER SWITCH
RM1880E _59 Vehicle Exterior _013252 LIGHTING (EXT) _0068743 HEADLIGHT DIMMER SWITCH G

LIGHTING (EXT)  HEADLIGHT DIMMER SWITCH  INSPECTION  


PROCEDURE

Hide 1.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for LHD)

a.
E218654
0.688,0.438 1.083,0.906 true 0.552,0.948 0.906,0.948 true 0.5,1.563 0.917,1.229 true 0.833,1.625 1.302,1.219 true 1.323,1.563 1.479,1.24 true 1.729,1.24 1.729,1.583 true 1.938,1.25 2.104,1.563 true 2.135,1.229 2.458,1.552 true 2.333,1.208 2.729,1.615 true 2.521,1.177 2.854,1.177 true 0.115,0.052 0.438,0.302 0.323,0.25 10 false *a 0.219,0.885 0.635,1.135 0.417,0.25 10 false LFG 0.344,0.365 0.76,0.615 0.417,0.25 10 false BFG 0.385,1.604 0.719,1.906 0.333,0.302 10 false B1 0.719,1.656 1.01,1.938 0.292,0.281 10 false ED 1.219,1.615 1.594,1.927 0.375,0.313 10 false T1 1.635,1.615 1.99,1.896 0.354,0.281 10 false HU 2.063,1.625 2.385,1.927 0.323,0.302 10 false HL 2.427,1.604 2.656,1.854 0.229,0.25 10 false E 2.927,1.094 3.219,1.354 0.292,0.26 10 false TL 2.677,1.656 2.979,1.917 0.302,0.26 10 false TR
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the light control switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (HU) - 11 (ED) Light control switch off 10 kΩ or higher
8 (HL) - 11 (ED)
13 (B1) - 10 (T1) Light control switch tail Below 1 Ω
9 (HU) - 11 (ED) Light control switch head Below 1 Ω
8 (HL) - 11 (ED)


If the result is not as specified, replace the headlight dimmer switch assembly.



b.

Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (HU) - 11 (ED) Headlight dimmer switch hi beam Below 1 Ω


HINT:

Perform the flash and high beam inspection with the light control switch on head.


If the result is not as specified, replace the headlight dimmer switch assembly.



c.

Inspect the turn signal switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
6 (TR) - 7 (E) Turn signal switch right turn Below 1 Ω
6 (TR) - 7 (E) Turn signal switch right lane change Below 1 Ω
6 (TR) - 7 (E) Turn signal switch neutral 10 kΩ or higher
5 (TL) - 7 (E)
5 (TL) - 7 (E) Turn signal switch left lane change Below 1 Ω
5 (TL) - 7 (E) Turn signal switch left turn Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



d.

Inspect the fog light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
3 (BFG) - 4 (LFG) Fog light switch off 10 kΩ or higher
3 (BFG) - 4 (LFG) Front fog light switch on Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



Hide 2.INSPECT HEADLIGHT DIMMER SWITCH ASSEMBLY (for RHD)

a.
E218654
2.531,0.927 2.885,0.927 true 2.344,0.896 2.802,0.448 true 2.542,1.177 2.906,1.406 true 2.125,1.229 2.5,1.667 true 1.927,1.24 2.135,1.615 true 1.74,1.25 1.74,1.604 true 1.51,1.26 1.365,1.615 true 1.313,1.24 1.021,1.604 true 1.115,1.229 0.719,1.615 true 0.906,1.188 0.5,1.188 true 0.115,0.052 0.417,0.26 0.302,0.208 10 false *a 2.938,0.833 3.26,1.021 0.323,0.188 10 false LFG 2.865,0.354 3.281,0.573 0.417,0.219 10 false BFG 2.979,1.354 3.24,1.625 0.26,0.271 10 false B1 2.531,1.625 2.802,1.833 0.271,0.208 10 false ED 2.104,1.677 2.323,1.906 0.219,0.229 10 false T1 1.667,1.677 1.927,1.885 0.26,0.208 10 false HU 1.271,1.656 1.51,1.833 0.24,0.177 10 false HL 0.927,1.656 1.125,1.854 0.198,0.198 10 false E 0.469,1.583 0.708,1.802 0.24,0.219 10 false TL 0.25,1.104 0.521,1.344 0.271,0.24 10 false TR
*a Component without harness connected
(Headlight Dimmer Switch Assembly)


Inspect the light control switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (HU) - 7 (ED) Light control switch off 10 kΩ or higher
10 (HL) - 7 (ED)
5 (B1) - 8 (T1) Light control switch tail Below 1 Ω
9 (HU) - 7 (ED) Light control switch head Below 1 Ω
10 (HL) - 7 (ED)


If the result is not as specified, replace the headlight dimmer switch assembly.



b.

Inspect the headlight dimmer switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
9 (HU) - 7 (ED) Headlight dimmer switch hi beam Below 1 Ω


HINT:

Perform the flash and high beam inspection with the light control switch on head.


If the result is not as specified, replace the headlight dimmer switch assembly.



c.

Inspect the turn signal switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
13 (TR) - 11 (E) Turn signal switch right turn Below 1 Ω
13 (TR) - 11 (E) Turn signal switch right lane change Below 1 Ω
13 (TR) - 11 (E) Turn signal switch neutral 10 kΩ or higher
12 (TL) - 11 (E)
12 (TL) - 11 (E) Turn signal switch left lane change Below 1 Ω
12 (TL) - 11 (E) Turn signal switch left turn Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.



d.

Inspect the fog light switch.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
2 (BFG) - 1 (LFG) Fog light switch off 10 kΩ or higher
2 (BFG) - 1 (LFG) Front fog light switch on Below 1 Ω


If the result is not as specified, replace the headlight dimmer switch assembly.