Home › Engine / Hybrid System › 2TR-FE STARTING › STARTER › from 2013.08
RM1880E _51 Engine / Hybrid System _013216 2TR-FE STARTING _0068502 STARTER G

2TR-FE STARTING  STARTER  INSPECTION  


PROCEDURE

Hide 1.INSPECT STARTER ASSEMBLY

CAUTION:

As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.


NOTICE:

The following tests must be done within 3 to 5 seconds to prevent the coil from burning out.


a.

Mount the starter assembly in a vise between aluminum plates.


b.

Perform the pull-in test.

i.

Remove the nut and disconnect the lead wire from terminal C.


ii.
A221364
2.167,0.802 2.333,0.438 2.333,0.438 2.5,0.438 true 1.948,0.865 2.115,1.844 2.115,1.844 1.896,1.844 true 2.542,0.354 2.854,0.51 0.313,0.156 10 false *1 1.729,1.75 2.042,1.906 0.313,0.156 10 false *2
*1 Terminal C
*2 Terminal 50
V100135

Move


Connect the battery to the magnet starter switch as shown in the illustration. Check that the clutch pinion gear extends.

If the clutch pinion gear does not move, replace the magnet starter switch assembly.



c.
A221365
2.167,0.802 2.375,0.438 2.375,0.438 2.583,0.438 true 2.625,0.365 2.938,0.521 0.313,0.156 10 false *1
*1 Terminal C
V100135

Disconnect


Perform the holding test.

i.

Maintain the battery connections of the pull-in test above, but disconnect the negative (-) lead from terminal C. Check that the pinion gear remains extended.

If the clutch pinion gear returns inward, replace the magnet starter switch assembly.



d.
A300400
1.385,1.021 1.542,1.219 0.156,0.198 10 false .
V100135

Disconnect
V100136

Move


Inspect the clutch pinion gear return.

i.

Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns.

If the clutch pinion gear does not return, replace the magnet starter switch assembly.



e.

Perform the no-load performance test.

i.

Connect the lead wire to terminal C with the nut. Make sure that the lead wire is not grounded.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


ii.

Mount the starter assembly in a vise between aluminum plates.


iii.
A227340
2.146,0.563 2.354,0.365 2.354,0.365 2.51,0.365 true 1.938,0.854 1.938,1.823 1.938,1.823 2.094,1.823 true 2.594,2.719 2.594,2.344 2.594,2.344 2.458,2.344 false 2.552,0.302 2.865,0.458 0.313,0.156 10 false *1 2.135,1.75 2.448,1.906 0.313,0.156 10 false *2 2.292,2.281 2.604,2.438 0.313,0.156 10 false *3
*1 Terminal 30
*2 Terminal 50
*3 Ammeter Probe
V100135

Move


Connect the battery and an ammeter probe to the starter assembly as shown in the illustration.


iv.

Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

Standard current:

90 A or less at 11.5 V


If the result is not as specified, replace the starter assembly.



Hide 2.INSPECT STARTER ARMATURE ASSEMBLY

a.

Check the commutator for dirt and/or burns on the surface.

If the surface is dirty or burnt, correct it with 400-grit sandpaper or a lathe.


b.

Inspect the commutator for an open circuit.

i.
A122065
1.719,0.969 2.125,0.333 2.125,0.333 2.229,0.333 true 2.302,0.24 2.479,0.396 0.177,0.156 10 *1
*1 Segment


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Segment Always Below 1 Ω


If the result is not as specified, replace the starter armature assembly.



c.

Inspect the commutator for a short circuit.

i.
A122066
2.125,0.854 2.521,0.438 2.521,0.438 2.594,0.438 true 1.563,0.688 1.958,0.281 1.958,0.281 2.042,0.281 true 2.615,0.354 2.833,0.51 0.219,0.156 10 *1 2.073,0.198 2.292,0.354 0.219,0.156 10 *2
*1 Segment
*2 Armature Coil Core


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Segment - Armature coil core Always 10 kΩ or higher


If the result is not as specified, replace the starter armature assembly.



d.
A300395

Using a vernier caliper, measure the commutator diameter.

Standard diameter:

29.0 mm (1.14 in.)


Minimum diameter:

28.0 mm (1.10 in.)


If the diameter is less than the minimum, replace the starter armature assembly.


e.
A122067

Check the commutator circle runout.

i.

Place the shaft of the starter armature assembly on V-blocks.


ii.

Using a dial indicator, measure the circle runout.

Maximum commutator runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, replace the starter armature assembly.



f.
A115027

Measure the undercut depth of the commutator.

Standard undercut depth:

0.7 mm (0.0276 in.)


Minimum undercut depth:

0.2 mm (0.00787 in.)


If the undercut depth is less than the minimum, correct it with a hacksaw blade.


Hide 3.INSPECT STARTER BRUSH HOLDER ASSEMBLY

a.

Using a vernier caliper, measure the brush length.

A300396
2.438,1 2.604,0.833 2.604,0.833 2.75,0.833 false 1.688,0.771 1.521,0.521 1.521,0.521 1.354,0.521 false 1.198,0.448 1.51,0.604 0.313,0.156 10 false *1 2.802,0.76 3.115,0.917 0.313,0.156 10 false *2 5.802,0.229 6.115,0.385 0.313,0.156 10 false *3
*1 Brush *2 Spring
*3 Length - -


Standard length:

14.4 mm (0.567 in.)


Minimum length:

9.0 mm (0.354 in.)


If the length is less than the minimum, replace the starter brush holder assembly and starter yoke assembly.


b.
ST00019
0.74,1.396 0.99,1.396 0.99,1.396 1.344,1.698 false 2.25,1.323 2.521,1.01 2.521,1.01 2.729,1.01 false 0.552,1.323 0.865,1.479 0.313,0.156 10 *1 2.781,0.948 3.094,1.104 0.313,0.156 10 *2
*1 Brush
*2 Brush Spring


Inspect the load of the brush spring.

i.

Take a pull scale reading immediately after the brush spring separates from the brush

Standard spring load:

16 to 20 N (1.7 to 2.0 kgf, 3.6 to 4.5 lbf)


Minimum spring load:

6.7 N (0.7 kgf, 1.5 lbf)


If the load is less than the minimum, replace the starter brush holder assembly.



c.
A300397
2.073,0.594 2.292,0.177 2.292,0.177 2.49,0.177 true 0.875,1.938 1.063,1.938 1.063,1.938 1.438,1.656 true 0.625,1.135 1.094,1.135 true 2.396,1.146 2.865,1.146 true 2.521,0.094 2.76,0.292 0.24,0.198 10 false (+) 0.406,1.042 0.646,1.24 0.24,0.198 10 false (+) 2.906,1.052 3.146,1.25 0.24,0.198 10 false (-) 0.719,1.833 0.958,2.031 0.24,0.198 10 false (-)

Inspect the insulation.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Positive brush holder - Negative brush holder Always 10 kΩ or higher


If the result is not as specified, replace the starter brush holder assembly.



Hide 4.INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.

Check the gear teeth of the planetary gears and starter center bearing clutch for wear or damage. If any planetary gear is damaged, replace the planetary gear assembly.

If any gear of the starter center bearing clutch is damaged, replace the starter center bearing clutch sub-assembly.


b.
A221357
1.51,0.74 1.667,0.938 0.156,0.198 10 false .
V100135

Free
V100136

Lock


Check the movement of the clutch pinion gear.

i.

Rotate the clutch pinion gear clockwise and check that it turns freely.


ii.

Try to rotate the clutch pinion gear counterclockwise and check that it locks. If the clutch pinion gear cannot be turned clockwise smoothly, or does not lock in the counterclockwise direction, replace the starter center bearing clutch sub-assembly.



Hide 5.INSPECT MAGNET STARTER SWITCH ASSEMBLY

a.
A300398

Push in the plunger and check that it returns quickly to its original position.

If the result is not as specified, replace the magnet starter switch assembly.


b.
A194284
1.844,0.813 2.146,0.635 2.146,0.635 2.333,0.635 false 1.583,1.167 1.271,1.604 1.271,1.604 1.083,1.604 false 0.927,1.552 1.24,1.708 0.313,0.156 10 false *2 2.375,0.563 2.688,0.719 0.313,0.156 10 false *1
*1 Terminal 50
*2 Terminal C


Check the pull-in coil for an open circuit.

i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Terminal C Always Below 1 Ω


If the result is not as specified, replace the magnet starter switch assembly.



c.

Check the holding coil for an open circuit.

i.
A194285
1.24,0.948 1.594,0.427 1.594,0.427 1.75,0.427 false 2.063,1.177 2.24,0.938 2.24,0.938 2.406,0.938 false 2.479,0.875 2.719,1.146 0.24,0.271 10 false *1 1.833,0.354 2.094,0.573 0.26,0.219 10 false *2
*1 Terminal 50
*2 Switch Body


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Terminal 50 - Switch body Always Below 2 Ω


If the result is not as specified, replace the magnet starter switch assembly.