Home › Engine / Hybrid System › 2TR-FE STARTING › STARTER › from 2013.08
RM1880E _51 Engine / Hybrid System _013216 2TR-FE STARTING _0068502 STARTER A

2TR-FE STARTING  STARTER  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY

a.
A221358
0.917,0.167 1.083,0.167 1.083,0.167 1.385,0.25 false 0.396,1.177 0.563,1.177 0.563,1.177 0.677,1.01 false 1.667,1.771 1.917,1.771 false 0.76,0.083 1.073,0.24 0.313,0.156 10 false *1 0.24,1.083 0.552,1.24 0.313,0.156 10 false *2 1.958,1.698 2.271,1.854 0.313,0.156 10 false *3
*1 Starter Drive Pinion Lever
*2 Rubber Plate
*3 Starter Center Bearing Clutch Sub-assembly
V100135

High-temperature Grease


Apply high-temperature grease to the starter pinion drive lever as shown in the illustration.


b.
A221361
1.323,1.354 1.479,1.552 0.156,0.198 10 false .
V100135

High-temperature Grease


Install the starter center bearing clutch sub-assembly, rubber plate and starter pinion drive lever to the starter drive housing assembly.


c.

Apply high-temperature grease to the planetary gears and pins of the starter center bearing clutch sub-assembly as shown in the illustration.


d.

Install the 3 planetary gears to the starter center bearing clutch sub-assembly.


Hide 2.INSTALL STARTER ARMATURE ASSEMBLY

a.

Install the starter armature assembly to the starter yoke assembly.

NOTICE:

The magnet of the starter yoke may attract the starter armature when the starter commutator end frame is installed, causing the magnet to break.



Hide 3.INSTALL STARTER BRUSH HOLDER ASSEMBLY

a.

Install the starter brush holder assembly to the starter yoke assembly.


b.
A300399

Connect the 4 brushes to the starter brush holder assembly.

i.

Using a screwdriver, hold back the spring.


ii.

Connect the brush to the brush holder assembly.



c.
A194294
1.771,1 0.906,0.427 0.906,0.427 0.74,0.427 true 1.51,1.292 0.906,0.969 0.906,0.969 0.76,0.969 true 2.271,1.052 2.594,0.896 2.594,0.896 2.698,0.896 true 2.76,0.833 3.167,1.156 0.406,0.323 10 *2 0.5,0.906 0.938,1.271 0.438,0.365 10 *3 0.51,0.344 0.854,0.688 0.344,0.344 10 *1
*1 Grommet
*2 Motor Lead Line Positive (+) Side
*3 Brush Holder Plate Negative (-) Side


Insert a grommet between the positive (+) side of the motor lead line and the negative (-) side of the brush holder plate.


d.
A224839
2.135,0.188 2.302,0.188 2.302,0.188 2.469,0.354 false 3.167,0.167 3,0.167 3,0.167 2.865,0.438 true 1.979,0.125 2.292,0.281 0.313,0.156 10 false *1 3.208,0.094 3.417,0.25 0.208,0.156 10 false *2
*1 Rubber Part
*2 Starter Commutator End Frame Assembly


Align the rubber part of the starter yoke assembly with the groove of the starter commutator end frame assembly.


e.

Install the starter commutator end frame assembly with the 2 screws.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)


Hide 4.INSTALL STARTER YOKE ASSEMBLY

a.

Install the starter armature plate to the starter yoke assembly.


b.
A224840
2.198,1.302 2.583,0.583 2.583,0.583 2.75,0.583 true 2.875,1.781 2.875,1.146 2.875,1.146 3.042,1.146 true 2.802,0.51 3.115,0.667 0.313,0.156 10 false *1 3.083,1.063 3.313,1.229 0.229,0.167 10 false *2
*1 Protrusion
*2 Notch


Check that the notch of the starter armature plate fits over the protrusion of the starter yoke assembly.


c.
A224841
2.469,1.302 2.719,1.635 2.719,1.635 2.885,1.635 true 1.854,1.469 2.104,1.802 2.104,1.802 2.271,1.802 true 2.948,1.563 3.26,1.719 0.313,0.156 10 false *1 2.313,1.719 2.625,1.875 0.313,0.156 10 false *2
*1 Notch
*2 Protrusion


Align the protrusion of the starter yoke assembly with the notches inside the starter drive housing assembly and insert the starter yoke assembly into the starter drive housing assembly.


d.

Using a T25 "TORX" socket wrench, install the starter drive housing assembly with the 2 through bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 5.INSTALL MAGNET STARTER SWITCH ASSEMBLY

a.

Apply high-temperature grease to the plunger hook of the magnet starter switch assembly.


b.
A221354

Hang the plunger of the magnet starter switch assembly on the starter pinion drive lever from the upper side.


c.

Install the magnet starter switch assembly with the 2 nuts.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


d.

Connect the lead wire to terminal C with the nut.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)