Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE PEDAL › from 2014.08
RM1880E _54 Brake _013227 BRAKE SYSTEM (OTHER) _0068565 BRAKE PEDAL N

BRAKE SYSTEM (OTHER)  BRAKE PEDAL  ADJUSTMENT  


PROCEDURE

Hide 1.CHECK AND ADJUST BRAKE PEDAL HEIGHT

a.
C236936C08
2.271,0.99 2.271,0.292 2.271,0.292 2.073,0.292 false 1.646,1.677 1.542,2.583 1.542,2.583 1.542,2.854 false 1.552,1.646 1.365,2.49 1.365,2.49 1.292,2.49 false 1.865,0.198 2.156,0.49 0.292,0.292 10 false *1 1.135,2.406 1.469,2.688 0.333,0.281 10 false *2 1.479,2.875 1.771,3.167 0.292,0.292 10 false *3 2.333,3.51 2.646,3.833 0.313,0.323 10 false *a
*1 Stop Light Switch
*2 Push Rod
*3 Lock Nut
*4 Pedal Height


Check the pedal height.

Standard pedal height from dash panel:
Item Specified Condition
for LHD (Manual Transmission) 168.3 to 178.3 mm (6.626 to 7.019 in.)
for LHD (Automatic Transmission) 169.3 to 179.3 mm (6.666 to 7.059 in.)
for RHD (Manual Transmission) 156.9 to 166.9 mm (6.178 to 6.570 in.)



b.

Adjust the pedal height.

i.

Disconnect the connector from the stop light switch.


ii.

Remove the switch.


iii.

Loosen the push rod clevis lock nut.


iv.

Adjust the pedal height by turning the push rod.


v.

Tighten the lock nut.

Torque:
26 N*m (265 kgf*cm, 19 ft.*lbf)


vi.
C111301C09
0.615,1.198 0.615,1.771 false 2,1.333 2,1.729 false 1.229,0.49 1.229,0.188 1.229,0.188 1.573,0.188 false 1.656,0.115 1.927,0.313 0.271,0.198 10 false *2 0.542,1.813 0.771,2 0.229,0.188 10 false *1 1.938,1.76 2.094,1.917 0.156,0.156 10 false *3
*1 Brake Pedal
*2 Adjuster
*3 Stop Light Switch


Insert the switch into the adjuster until it slightly touches the pedal.

NOTICE:

Do not depress the pedal.



vii.
C111302C10
0.51,0.76 0.51,0.115 0.51,0.115 0.917,0.115 false 1.99,1.292 1.99,1.75 false 1.927,1.771 2.083,1.948 0.156,0.177 10 false *2 0.094,1.552 1.094,1.76 1,0.208 10 false 1.5 to 2.5 mm 0.969,0.063 1.135,0.26 0.167,0.198 10 false *1
*1 Shaft
*2 Stop Light Switch


Turn the switch a quarter turn clockwise.

Torque:
1.5 N*m (15 kgf*cm, 13 in.*lbf)

or less


NOTICE:

Do not depress the pedal.



viii.

Connect the connector to the switch.


ix.

Check the switch clearance.

Standard stop light switch clearance:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)




Hide 2.CHECK BRAKE PEDAL FREE PLAY

C111306C08
2.066,1.437 2.225,1.595 0.159,0.158 10 *a
*a Pedal Free Play


a.

Stop the engine. Depress the pedal several times until there is no vacuum in the booster. Then release the pedal.


b.

Depress the pedal until resistance is felt.


c.

Check the pedal free play by measuring the distance between the position in the previous step and the pedal's released position.

Standard pedal free play:

1.0 to 6.0 mm (0.0394 to 0.236 in.)


If the free play is not as specified, check the switch clearance in the next step.

If the free play is as specified, proceed to the "CHECK BRAKE PEDAL RESERVE DISTANCE" procedure.


d.

Check the switch clearance.

Standard stop light switch clearance:

1.5 to 2.5 mm (0.0591 to 0.0984 in.)


If the clearance is not as specified, adjust the clearance and recheck the pedal's free play.

If the clearance is as specified, troubleshoot the brake system and proceed to the "CHECK BRAKE PEDAL RESERVE DISTANCE" procedure.


Hide 3.CHECK BRAKE PEDAL RESERVE DISTANCE

C111339C07
0.885,1.271 0.885,1.667 false 1.479,1.406 1.656,1.604 0.177,0.198 10 *a 0.813,1.688 0.969,1.885 0.156,0.198 10 *1
*1 Dash Panel
*a Pedal Reserve Distance


a.

Release the parking brake lever. Start the engine.


b.

Depress the pedal and check the pedal reserve distance.

i.

Depress the pedal with a force of 490 N (50 kgf, 110 lbf).


ii.

Measure the distance between the pedal and dash panel shown in the illustration.

Standard pedal reserve distance:
Item Specified Condition
for LHD 92.0 mm (3.622 in.)
for RHD 85.0 mm (3.346 in.)


If the distance is not as specified, troubleshoot the brake system.