2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A102672E01
    Using SST and a press, press in a new bearing.
    SST
    09950-60010   (09951-00520)
    09950-70010   (09951-07100)

  1. A079311E02
    Align the claws of the bearing retainer with the grooves inside the generator drive end frame.
    Text in Illustration 
    *1
    Claw

  1. Install the bearing retainer with the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the rotor and washer to the drive end frame.


3. INSTALL GENERATOR COIL ASSEMBLY

  1. A158387E02
    Using a deep socket wrench (21 mm) and press, slowly press on the generator coil.
    Text in Illustration 
    *1
    Deep Socket Wrench (21 mm)

  1. A079304
    Install the generator coil with the 4 through bolts.

    Torque:
    5.8 N*m{ 59 kgf*cm , 51 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A113845E06
    While pushing the 2 brushes into the generator brush holder, insert a φ1.0 mm (0.0394 in.) pin into the generator brush holder hole.
    Text in Illustration 
    *1
    Pin

  1. A079303E03
    Install the brush holder with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

  1. Pull out the pin from the brush holder.

    Text in Illustration 
    *1
    Pin


5. INSTALL TERMINAL INSULATOR

A079318

6. INSTALL GENERATOR REAR END COVER
  1. Install the generator rear end cover with the 3 nuts.

    Torque:
    4.6 N*m{ 46 kgf*cm , 40 in.*lbf }


7. INSTALL GENERATOR WITH CLUTCH PULLEY
  1. Install the pulley by hand.

  1. Mount generator in a vise between aluminum plates.

  1. A224863E01
    Install SST (A) and (B) to the generator with clutch pulley as shown in the illustration.
    SST
    09820-63021  

    NOTICE:
    Securely attach SST to the generator with clutch pulley and generator rotor shaft.

  1. A224865E01

    Torque:
    without SST:
    111 N*m{ 1127 kgf*cm , 81 ft.*lbf }
    with SST:
    83 N*m{ 844 kgf*cm , 61 ft.*lbf }

    Text in Illustration 
    *1
    Fulcrum Length
    *a
    Hold
    V100135
    Turn

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.). When using a torque wrench with a fulcrum length that is not 300 mm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.

    NOTICE:
    Be careful as the generator with clutch pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.

  1. Remove SST from the generator.

  1. Check that the generator pulley rotates smoothly.

  1. Install a new generator pulley cap.

← INSPECTION (from Aug 2013)INSTALLATION (Aug 2013 – Jul 2014) →