2013-2015 Land Cruiser Prado · Service Manual Power Source / Network

REASSEMBLY

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. INSTALL GENERATOR DRIVE END FRAME BEARING

  1. A115870E01
    Using SST and a press, press in a new generator drive end frame bearing.
    SST
    09950-60010   (09951-00470)
    09950-70010   (09951-07100)

  1. A115871E02
    Align the claws of the retainer plate with the grooves inside the drive end frame.
    Text in Illustration 
    *1
    Claw

  1. Install the retainer plate with the 4 screws.

    Torque:
    2.3 N*m{ 23 kgf*cm , 20 in.*lbf }


2. INSTALL GENERATOR ROTOR ASSEMBLY
  1. Install the generator rotor to the drive end frame.

  1. Install the washer to the generator rotor.


3. INSTALL GENERATOR COIL ASSEMBLY

  1. A102584E02
    Using a deep socket wrench (21 mm) and press, slowly press on the generator coil.
    Text in Illustration 
    *1
    Deep Socket Wrench (21 mm)

  1. Install the generator coil with the 4 through bolts.

    Torque:
    5.9 N*m{ 60 kgf*cm , 52 in.*lbf }


4. INSTALL GENERATOR BRUSH HOLDER ASSEMBLY

  1. A113845E05
    While pushing the 2 brushes into the generator brush holder, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the generator brush holder hole.
    Text in Illustration 
    *1
    Pin

  1. A220309E01
    Install the generator brush holder with the 2 screws.

    Torque:
    1.8 N*m{ 18 kgf*cm , 16 in.*lbf }

    Text in Illustration 
    *1
    Pin

  1. Pull out the pin from the brush holder.


5. INSTALL TERMINAL INSULATOR

  1. A102585
    Install the terminal insulator.


6. INSTALL GENERATOR REAR END COVER
  1. Install the generator rear end cover with the 3 nuts.

    Torque:
    4.6 N*m{ 46 kgf*cm , 40 in.*lbf }


7. INSTALL GENERATOR WITH CLUTCH PULLEY
  1. Temporarily install the generator with clutch pulley by hand.

  1. Mount the generator in a vise between aluminum plates.

  1. A219550E01
    Install SST (A) and SST (B) to the generator with clutch pulley as shown in the illustration.
    SST
    09820-63021  
    Text in Illustration 
    *1
    Rotor Shaft

    NOTICE:
    Securely attach SST to the generator with clutch pulley and generator rotor shaft.

  1. A219552E02
    Using a wrench to hold SST (A), turn SST (B) clockwise to tighten the generator with clutch pulley.

    Torque:
    without SST:
    111 N*m{ 1127 kgf*cm , 81 ft.*lbf }
    with SST:
    88 N*m{ 897 kgf*cm , 65 ft.*lbf }

    Text in Illustration 
    *1
    Fulcrum Length
    *a
    Hold
    V100135
    Turn

    HINT:
    1. Use a torque wrench with a fulcrum length of 400 mm (15.7 in.). When using a torque wrench with a fulcrum length that is not 400 mm (15.7 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.

    NOTICE:
    Be careful as the generator with clutch pulley or generator rotor shaft may be damaged if the position of SST is not securely maintained while performing this operation.

  1. Remove SST from the generator.

  1. Check that the generator with clutch pulley rotates smoothly.


8. INSTALL GENERATOR PULLEY CAP
  1. Install a new generator pulley cap to the generator with clutch pulley.

← INSPECTION (from Aug 2013)REASSEMBLY (from Aug 2014) →