2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

REMOVAL

Removal / installation · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
  1. After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
  2. When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY (w/ EGR System)
  1. Remove the electric EGR control valve (Click here).


3. DISCONNECT INLET HEATER WATER HOSE (w/o EGR System)

  1. A224418
    Remove the bolt and disconnect the inlet heater water hose.


4. DISCONNECT NO. 4 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY (w/o EGR System)

  1. A222558
    Remove the bolt and disconnect the No. 4 vacuum transmitting pipe.


5. REMOVE NO. 1 INTAKE PIPE (w/o EGR System)

  1. A222559
    Disconnect the 3 connectors from the intake air temperature sensor, throttle control motor and manifold absolute pressure sensor.

  1. Detach the 2 clamps.

  1. Disconnect the vacuum hose from the manifold absolute pressure sensor.

  1. A222560
    Loosen the 2 hose clamps of the No. 1 air hose.

  1. A222561
    Loosen the hose clamp of the intercooler air hose.

  1. A222562
    Remove the 2 bolts and No. 1 intake pipe.


6. REMOVE THROTTLE BODY BRACKET (w/o EGR System)

  1. A230166
    Disconnect the vacuum hose.

  1. Remove the bolt and gas filter with gas filter bracket.

  1. Remove the 2 bolts and throttle body bracket.


7. REMOVE NO. 1, NO. 2 AND NO. 3 INJECTION PIPE SUB-ASSEMBLY (w/o EGR System)

NOTICE:
  1. After removing the injection pipe, cover the outlets on the common rail with tape to keep out foreign matter.
  2. After removing the injection pipe, put it in a plastic bag to prevent foreign matter from contaminating its injector inlet.

  1. A223285
    Remove the 2 nuts and No. 3 injection pipe clamp.

  1. A223286
    Remove the 2 bolts and 2 No. 2 injection pipe clamps.

  1. A223287E01
    Using a 17 mm union nut wrench, loosen the union nuts and remove the No. 1, No. 2 and No. 3 injection pipes.
    Text in Illustration 
    *a
    Injector Side
    *b
    Common Rail Side


8. REMOVE AIR CONNECTOR STAY (w/o EGR System)

  1. A230167
    Remove the 3 bolts and air connector stay.


9. DISCONNECT ENGINE WIRE (w/o EGR System)

  1. A225769
    for LHD:
    Remove the 2 bolts and disconnect the clamp and engine wire.

  1. A225770
    for RHD:
    Remove the bolt and disconnect the engine wire.


10. REMOVE INTAKE AIR CONNECTOR WITH DIESEL THROTTLE BODY ASSEMBLY (w/o EGR System)

  1. A230087
    Disconnect the throttle position sensor connector.

  1. A230165
    Remove the 3 bolts, intake air connector with diesel throttle and gasket.


11. REMOVE INTAKE PIPE STAY

  1. A220705
    Remove the bolt and intake pipe stay.


12. REMOVE NO. 2 MANIFOLD STAY

  1. A222609
    Remove the bolt and No. 2 manifold stay.


13. REMOVE NO. 1 GLOW PLUG CONNECTOR

A222606
  1. Remove the screw grommet and nut and disconnect the wire harness from the No. 1 glow plug connector.

  1. Remove the 4 screw grommets, 4 nuts and No. 1 glow plug connector.


14. REMOVE NO. 1 INTAKE MANIFOLD INSULATOR

A222607

15. REMOVE GLOW PLUG

A222608
  1. Remove the 4 glow plugs.

← ON-VEHICLE INSPECTION (from Aug 2014)REMOVAL (from Aug 2014) →