2013-2015 Land Cruiser Prado · Service Manual Drivetrain

FAIL-SAFE CHART

System information · Vehicles built from Aug 2013


Fail-safe
This function minimizes the loss of ECT functions when a malfunction occurs in a sensor or solenoid.

Fail-safe control list
Malfunctioning Part
Function
DTC P0717:
Input Speed Sensor NCO
During an input speed sensor malfunction, shift control is performed using the output speed sensor signal (SP2).
During an input speed sensor malfunction, AI-SHIFT*1 and flex lock-up clutch control are prohibited.
DTC P0722:
Output Speed Sensor SP2
During an output speed sensor malfunction, shift control is performed using the input speed sensor signal (NCO).
During an output speed sensor malfunction, AI-SHIFT*1 and flex lock-up clutch control are prohibited.
DTC P2742, P2743:
No. 1 ATF Temperature Sensor
During a No. 1 ATF temperature sensor malfunction, flex lock-up clutch control is prohibited.
DTC P0973, P0974, P0976, P0977:
Shift Solenoid Valve S1, S2
The current to the malfunctioning solenoid valve is cut off and control is performed by operating the other normal solenoid valve.
Shift control is performed depending on the failed solenoid as described in the table below.
DTC P2714, P2716:
Shift Solenoid Valve SLT
During a solenoid valve SLT malfunction, the current to the solenoid valve is stopped. This stops optimal line pressure control and shift shock increases. However, shifting is performed using normal clutch pressure control.
DTC P2757, P2759:
Shift Solenoid Valve SLU
During a solenoid valve SLU malfunction, the current to the solenoid valve is stopped. This stops lock-up control and flex lock-up control, and fuel economy decreases.

HINT:
*: In addition to the switching of the shift pattern through the pattern select switch, Artificial Intelligence Shift (AI-SHIFT) control enables the ECM to estimate the road conditions and the driver's intention in order to automatically select the optimal shift pattern.

Shift Solenoid Valve Normal Operation Chart 
Shift Lever Position
Gear
Shift Solenoid Valve S1
Shift Solenoid Valve S2
D
1st
ON
OFF
2nd
ON
ON
3rd
OFF
ON
4th
OFF
OFF
3
1st
ON
OFF
2nd
ON
ON
3rd
OFF
ON
2
1st
ON
OFF
2nd
ON
ON
L
1st
ON
OFF
  1. Fail-safe operation for electronically malfunctioning shift solenoid valve (S1 and S2).

    1. Fail-safe function
      If either of the shift solenoid valve circuits has an open or short failure, the ECM turns the other shift solenoid valve ON and OFF in order to shift into the gear positions shown in the table below. Also, the ECM stops sending current to the open or short-circuited solenoid.
      Even if starting the engine again in fail-safe mode, the gear position remains in the same position.

      HINT:
      X: OFF (the ECM stops sending current to the malfunctioning solenoid valve).

      Shift Solenoid Valve Electrical Malfunction 
      Shift Lever Position
      Shift Solenoid Valve S1
      Shift Solenoid Valve S2
      Shift Solenoid Valve S1 and S2
      Shift Solenoid Valve S1
      Shift Solenoid Valve S2
      Gear
      Shift Solenoid Valve S1
      Shift Solenoid Valve S2
      Gear
      Gear when Shift Lever is Manually Operated
      D
      X
      OFF
      4th
      ON
      X
      1st
      4th
      X
      ON
      3rd
      ON
      X
      1st
      4th
      X
      ON
      3rd
      OFF
      X
      4th
      4th
      X
      OFF
      4th
      OFF
      X
      4th
      4th
      3
      X
      OFF
      4th
      ON
      X
      1st
      4th
      X
      ON
      3rd
      ON
      X
      1st
      4th
      X
      ON
      3rd
      OFF
      X
      4th
      4th
      2
      X
      ON
      3rd
      ON
      X
      1st
      3rd
      X
      ON
      3rd
      OFF
      X
      3rd
      3rd
      L
      X
      OFF
      1st
      ON
      X
      1st
      1st

← CHECK MODE PROCEDURE (from Aug 2014)DATA LIST / ACTIVE TEST (Aug 2013 – Jul 2014) →