2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

TERMINALS OF ECM

System information · Vehicles built from Aug 2013


CHECK ECM
A225776E07
  1. Measure the voltage of the ECM connectors.

    HINT:
    The standard voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard voltage for that pair of terminals, displayed in the "Specified Condition" column. The illustration above can be used as a reference to identify the ECM terminal locations.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    G55-24 (BATT) - C36-12 (E1)
    L - BR
    Battery (for measuring battery voltage and for ECM memory)
    Always
    11 to 14 V
    C36-23 (+BM) - C36-12 (E1)
    GR - BR
    Power source of throttle actuator
    Always
    11 to 14 V
    G56-21 (IGSW) - C36-12 (E1)
    W - BR
    Ignition switch
    Ignition switch ON
    11 to 14 V
    G55-22 (+B) - C36-12 (E1)
    W - BR
    Power source of ECM
    Ignition switch ON
    11 to 14 V
    G55-23 (+B2) - C36-12 (E1)
    W - BR
    Power source of ECM
    Ignition switch ON
    11 to 14 V
    C35-19 (OC1+) - C35-20 (OC1-)
    G-Y - L-B
    Camshaft timing oil control valve assembly (for Intake Side of Bank 1)
    Ignition switch ON
    Pulse generation (see waveform 1)
    C34-19 (OC2+) - C34-20 (OC2-)
    L-W - L-R
    Camshaft timing oil control valve assembly (for Intake Side of Bank 2)
    Ignition switch ON
    Pulse generation
    (see waveform 1)
    C35-21 (OE1+) - C35-22 (OE1-)
    G-B - B-R
    Camshaft timing oil control valve assembly (for Exhaust Side of Bank 1)
    Ignition switch ON
    Pulse generation
    (see waveform 1)
    C34-21 (OE2+) - C34-22 (OE2-)
    W-G - L
    Camshaft timing oil control valve assembly (for Exhaust Side of Bank 2)
    Ignition switch ON
    Pulse generation
    (see waveform 1)
    G55-9 (MREL) - C36-12 (E1)
    V - BR
    EFI relay
    Ignition switch ON
    11 to 14 V
    C35-14 (VG) - C35-13 (E2G)
    W-R - B-W
    Mass air flow meter
    Idling, shift lever in P or N, A/C switch off
    0.5 to 3.0 V
    C35-15 (THA) - C35-7 (ETHA)
    Y-B - W-R
    Intake air temperature sensor
    Idling, intake air temperature 20°C (68°F)
    0.5 to 3.4 V
    C36-17 (THW) - C35-8 (ETHW)
    R-L - W-R
    Engine coolant temperature sensor
    Idling, engine coolant temperature 80°C (176°F)
    0.2 to 1.0 V
    C36-13 (VCTA) - C36-14 (ETA)
    L - W
    Power source for throttle position sensor (fixed voltage)
    Ignition switch ON
    4.5 to 5.5 V
    C36-15 (VTA1) - C36-14 (ETA)
    LG - W
    Throttle position sensor (for engine control)
    Ignition switch ON,
    throttle valve fully closed
    0.5 to 1.1 V
    Ignition switch ON,
    throttle valve fully open
    3.3 to 4.9 V
    C36-16 (VTA2) - C36-14 (ETA)
    G-W - W
    Throttle position sensor (for sensor malfunction detection)
    Ignition switch ON,
    throttle valve fully closed
    2.1 to 3.1 V
    Ignition switch ON,
    throttle valve fully open
    4.6 to 5.0 V
    G56-6 (VPA) - G56-3 (EPA)
    L - P
    Accelerator pedal position sensor (for engine control)
    Ignition switch ON,
    accelerator pedal released
    0.5 to 1.1 V
    Ignition switch ON,
    accelerator pedal fully depressed
    2.6 to 4.5 V
    G56-5 (VPA2) - G56-1 (EPA2)
    GR - W
    Accelerator pedal position sensor (for sensor malfunction detection)
    Ignition switch ON,
    accelerator pedal released
    1.2 to 2.0 V
    Ignition switch ON,
    accelerator pedal fully depressed
    3.4 to 4.75 V
    G56-4 (VCPA) - G56-3 (EPA)
    LG - P
    Power source of accelerator pedal position sensor (for VPA)
    Ignition switch ON
    4.5 to 5.5 V
    G56-2 (VCP2) - G56-1 (EPA2)
    R - W
    Power source of accelerator pedal position sensor (for VPA2)
    Ignition switch ON
    4.5 to 5.5 V
    C37-17 (HA1A) - C37-16 (E04)
    C37-19 (HA2A) - C37-16 (E04)
    R-L - W-B
    B-W - W-B
    Air fuel ratio sensor heater
    Idling
    Below 3.0 V
    Ignition switch ON
    11 to 14 V
    C36-1 (A1A+) - C36-12 (E1)
    P -BR
    Air fuel ratio sensor
    Ignition switch ON
    3.3 V*
    C36-2 (A1A-) - C36-12 (E1)
    L - BR
    Air fuel ratio sensor
    Ignition switch ON
    3.0 V*
    C36-7 (A2A+) - C36-12 (E1)
    Y - BR
    Air fuel ratio sensor
    Ignition switch ON
    3.3 V*
    C36-8 (A2A-) - C36-12 (E1)
    L - BR
    Air fuel ratio sensor
    Ignition switch ON
    3.0 V*
    C37-12 (HT1B) - C37-11 (E03)
    C37-13 (HT2B) - C37-11 (E03)
    L-R - W-B
    L - W-B
    Heated oxygen sensor heater
    Idling
    Below 3.0 V
    Ignition switch ON
    11 to 14 V
    C34-2 (OX1B) - C34-1 (EX1B)
    C34-4 (OX2B) - C34-3 (EX2B)
    B - L-W
    B - GR
    Heated oxygen sensor
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
    Pulse generation (see waveform 2)
    C37-6 (#10) - C37-14 (E01)
    C37-1 (#20) - C37-14 (E01)
    C37-7 (#30) - C37-14 (E01)
    C37-2 (#40) - C37-14 (E01)
    C37-8 (#50) - C37-14 (E01)
    C37-3 (#60) - C37-14 (E01)
    L - W-B
    B - W-B
    R - W-B
    G - W-B
    Y - W-B
    R-L - W-B
    Fuel injector assembly
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation (see waveform 3)
    C35-11 (KNK1) - C35-12 (EKNK)
    C35-5 (KNK2) - C35-6 (EKN2)
    B - W
    G - R
    Knock sensor
    Engine speed maintained at 4000 rpm after warming up engine
    Pulse generation (see waveform 4)
    C34-15 (VCV1) - C36-12 (E1)
    P-L - BR
    Power source for sensor (specific voltage)
    Ignition switch ON
    4.5 to 5.5 V
    C34-16 (VCV2) - C36-12 (E1)
    LG-B - BR
    Power source for sensor (specific voltage)
    Ignition switch ON
    4.5 to 5.5 V
    C34-9 (VV1+) - C34-10 (VV1-)
    R - G
    VVT sensor (for Intake Side of Bank 1)
    Idling
    Pulse generation
    (see waveform 5)
    C34-12 (VV2+) - C34-11 (VV2-)
    G - GR
    VVT Sensor (for Intake Side of Bank 2)
    Idling
    Pulse generation
    (see waveform 5)
    C34-13 (EV1+) - C34-14 (EV1-)
    W-R - R-B
    VVT Sensor (for Exhaust Side of Bank 1)
    Idling
    Pulse generation
    (see waveform 6)
    C34-18 (EV2+) - C34-17 (EV2-)
    L - P
    VVT Sensor (for Exhaust Side of Bank 2)
    Idling
    Pulse generation
    (see waveform 6)
    C34-6 (NE+) - C34-5 (NE-)
    B - W
    Crankshaft position sensor
    Idling
    Pulse generation (see waveform 5)
    C36-24 (IGT1) - C36-12 (E1)
    C36-25 (IGT2) - C36-12 (E1)
    C36-26 (IGT3) - C36-12 (E1)
    C36-27 (IGT4) - C36-12 (E1)
    C36-28 (IGT5) - C36-12 (E1)
    C35-25 (IGT6) - C36-12 (E1)
    R-Y - BR
    R-L - BR
    G-B - BR
    G-W - BR
    GR - BR
    L - BR
    Ignition coil assembly (ignition signal)
    Idling
    Pulse generation (see waveform 7)
    C36-6 (IGF1) - C36-12 (E1)
    G-R - BR
    Ignition coil assembly (ignition confirmation signal)
    Ignition switch ON
    4.5 to 5.5 V
    Idling
    Pulse generation (see waveform 7)
    C36-18 (PRG) - C36-12 (E1)
    P - BR
    Purge VSV
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation (see waveform 8)
    G55-18 (SPD) - C36-12 (E1)
    R - BR
    Vehicle speed signal from combination meter assembly
    Driving at 20 km/h (12 mph)
    Pulse generation (see waveform 9)
    G56-10 (STA) - C36-12 (E1)
    W - BR
    Starter signal
    Cranking
    5.5 V or more
    C35-2 (NSW) - C36-12 (E1)
    B - BR
    Starter relay control
    Ignition switch ON
    Below 1.5 V
    Cranking
    6.0 V or more
    G56-18 (STP) - C36-12 (E1)
    V - BR
    Stop light switch
    Brake pedal depressed
    7.5 to 14 V
    Brake pedal released
    Below 1.5 V
    G55-8 (ST1-) - C36-12 (E1)
    B - BR
    Stop light switch
    (opposite to voltage at STP terminal)
    Ignition switch ON,
    Brake pedal depressed
    Below 1.5 V
    Ignition switch ON,
    Brake pedal released
    7.5 to 14 V
    C37-20 (M+) - C37-10 (ME01)
    P - W-B
    Throttle actuator
    Idling with warm engine
    Pulse generation (see waveform 10)
    C36-29 (M-) - C37-10 (ME01)
    L - W-B
    Throttle actuator
    Idling with warm engine
    Pulse generation (see waveform 11)
    G56-8 (FC) - C36-12 (E1)
    G - BR
    Fuel pump control
    Idling
    Below 1.5 V
    G55-3 (FPC) - C36-12 (E1)
    G - BR
    Fuel pump control
    Ignition switch ON
    Below 1.5 V
    G56-26 (DI) - C36-12 (E1)
    GR - BR
    Fuel pump control
    Ignition switch ON
    0 to 3.0 V
    C35-16 (PSP) - C36-12 (E1)
    V - BR
    Power steering oil pressure sensor
    Ignition switch ON
    0.5 to 4.5 V
    G55-1 (AIP) - C35-7 (ETHA)
    V - W-R
    Secondary air injection system pressure signal
    Ignition switch ON
    3.0 to 3.6 V
    G55-2 (AIP2) - C35-7 (ETHA)
    B - W-R
    Secondary air injection system pressure signal
    Ignition switch ON
    3.0 to 3.6 V
    C35-30 (AIDI) - C36-12 (E1)
    G - BR
    Air switching valve for secondary air injection system
    Air injection system operates
    Pulse generation (see waveform 12)
    C34-26 (AIRV) - C36-12 (E1)
    P - BR
    Air switching valve for secondary air injection system
    Ignition switch ON
    11 to 14 V
    C35-23 (AIRP) - C36-12 (E1)
    GR - BR
    Air switching valve for secondary air injection system
    Ignition switch ON
    11 to 14 V
    C36-21 (AIR1) - C36-12 (E1)
    L - BR
    Air switching valve for secondary air injection system
    Ignition switch ON
    11 to 14 V
    C36-20 (HAI1) - C36-12 (E1)
    W - BR
    Air pump heater for secondary air injection system
    AI heater operating
    11 to 14 V
    G55-13 (W) - C36-12 (E1)
    V - BR
    MIL
    Ignition switch ON
    Below 1.5 V
    Idling
    11 to 14 V
    G56-28 (TC) - C36-12 (E1)
    V - BR
    Terminal TC of DLC3
    Ignition switch ON
    11 to 14 V
    G56-29 (TACH) - C36-12 (E1)
    P - BR
    Engine speed
    Idling
    Pulse generation (see waveform 13)
    C35-28 (ALT) - C36-12 (E1)
    L - BR
    Generator
    Ignition switch ON
    11 to 14 V
    G56-32 (CANH) - C36-12 (E1)
    R - BR
    CAN communication line
    Ignition switch ON
    Pulse generation (see waveform 14)
    G56-31 (CANL) - C36-12 (E1)
    W - BR
    CAN communication line
    Ignition switch ON
    Pulse generation (see waveform 15)
    G56-34 (CANP) - C36-12 (E1)
    BR - BR
    CAN communication line
    Ignition switch ON
    Pulse generation (see waveform 14)
    G56-33 (CANN) - C36-12 (E1)
    GR - BR
    CAN communication line
    Ignition switch ON
    Pulse generation (see waveform 15)

    HINT:
    *: The ECM terminal voltage is constant regardless of the output voltage from the sensor.

  2. A093229E02
    Waveform 1
    Camshaft Timing Oil Control Valve Assembly 
    Symbol
    Between OC1+ and OC1-
    Between OC2+ and OC2-
    Between OE1+ and OE1-
    Between OE2+ and OE2-
    Tester Range
    5 V/DIV., 1 msec./DIV.
    Condition
    Idling

  3. A088863E05
    Waveform 2
    Heated Oxygen Sensor 
    Symbol
    Between OX1B and EX1B
    Between OX2B and EX2B
    Tester Range
    0.2 V/DIV., 200 msec./DIV.
    Condition
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

    HINT:
    In Data List, item O2S B1S2 and O2S B2S2 shows the ECM input values from the heated oxygen sensor.

  4. A093279E04
    Waveform 3
    Fuel Injector Assembly No. 1 (to No. 6) Injection Signal 
    Symbol
    Between #10 (to #60) and E01
    Tester Range
    20 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.

  5. A085286E03
    Waveform 4
    Knock Sensor 
    Symbol
    Between KNK1 and EKNK
    Between KNK2 and EKN2
    Tester Range
    1 V/DIV., 1 msec./DIV.
    Condition
    Engine speed maintained at 4000 rpm after warming up engine

    HINT:
    1. The wavelength becomes shorter as the engine speed increases.
    2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.

  6. A122767E04
    Waveform 5
    Crankshaft Position Sensor and VVT Sensor (for Intake Side) 
    Symbol
    Between NE+ and NE-
    Between VV1+ and VV1-
    Between VV2+ and VV2-
    Tester Range
    5 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.

  7. A122768E04
    Waveform 6
    Crankshaft position sensor and VVT sensor (for Exhaust Side) 
    Symbol
    Between NE+ and NE-
    Between EV1+ and EV1-
    Between EV2+ and EV2-
    Tester Range
    5 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.

  8. G035664E01
    Waveform 7
    Igniter IGT Signal (from ECM to Igniter) and Igniter IGF Signal (from Igniter to ECM) 
    Symbol
    Between IGT (1 to 6) and E1
    Between IGF1 and E1
    Tester Range
    2 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.

  9. A205411E02
    Waveform 8
    Purge VSV 
    Symbol
    Between PRG and E1
    Tester Range
    10 V/DIV., 20 msec./DIV.
    Condition
    Idling

    HINT:
    If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.

  10. A093224E01
    Waveform 9
    Vehicle Speed Signal 
    Symbol
    Between SPD and E1
    Tester Range
    2 V/DIV., 20 msec./DIV.
    Condition
    Driving at 20 km/h (12 mph)

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.

  11. A208000E06
    Waveform 10
    Throttle Actuator Positive Terminal 
    Symbol
    Between M+ and ME01
    Tester Range
    5 V/DIV., 1 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.

  12. A245848E04
    Waveform 11
    Throttle Actuator Negative Terminal 
    Symbol
    Between M- and ME01
    Tester Range
    5 V/DIV., 1 msec./DIV.
    Condition
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.

  13. G032718E03
    Waveform 12
    Terminal DI of Air Injection Control Driver 
    Symbol
    Between AIDI and E1
    Tester Range
    5 V/DIV., 20 msec./DIV.
    Condition
    Performing system check using intelligent tester (secondary air injection check)

    HINT:
    The wavelength changes when the air injection control driver detects malfunctions in the air injection system.

  14. A093225E01
    Waveform 13
    Engine Speed Signal 
    Symbol
    Between TACH and E1
    Tester Range
    5 V/DIV., 10 msec./DIV.
    Condition
    Idling

    HINT:
    The wavelength becomes shorter as the engine speed increases.

  15. A086154E01
    Waveform 14
    CAN Communication Signal 
    Symbol
    Between CANH and E1
    Between CANP and E1
    Tester Range
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.

  16. A086155E01
    Waveform 15
    CAN Communication Signal 
    Symbol
    Between CANL and E1
    Between CANN and E1
    Tester Range
    1 V/DIV., 10 μsec./DIV.
    Condition
    Engine stopped and ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.

← PROBLEM SYMPTOMS TABLE (from Aug 2014)DIAGNOSIS SYSTEM (Aug 2013 – Jul 2014) →