2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

FREEZE FRAME DATA

Troubleshooting · Vehicles built from Aug 2013


DESCRIPTION
  1. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was moving or stationary, whether the air fuel ratio was lean or rich, as well as the other data recorded at the time of a malfunction.

    HINT:
    If it is impossible to duplicate the problem even though a DTC is stored, confirm the freeze frame data.


  1. A103809E49
    The ECM records engine conditions in the form of freeze frame data every 0.5 seconds. Using an intelligent tester, 5 separate sets of freeze frame data can be checked.
    1. 3 data sets from before the DTC was stored
    2. 1 data set from when the DTC was stored
    3. 1 data set from after the DTC was stored
    1. These data sets can be used to simulate the condition of the vehicle from around the time of the occurrence of the malfunction. The data may assist in identifying the cause of the malfunction, and in judging whether it was temporary or not.

LIST OF FREEZE FRAME DATA
Tester Display
Measurement Item
Diagnostic Note
Vehicle Speed
Vehicle speed
The speed indicated on the speedometer.
Target Idle Engine Speed
Target idling speed
-
Engine Speed
Engine speed
-
Calculate Load
Calculated load
The load calculated by the ECM.
MAF
Mass air flow volume
If approximately 0.0 gm/s:
  1. The mass air flow meter power source circuit is open or shorted.
  2. The VG circuit is open or shorted.
  3. The E2G circuit is open.
Atmosphere Pressure
Atmospheric pressure
-
MAP
Absolute pressure inside intake manifold
-
Coolant Temp
Engine coolant temperature
If -40°C (-40°F), the sensor circuit is open.
If 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air
Intake air temperature
If -40°C (-40°F), the sensor circuit is open.
If 140°C (284°F) or higher, the sensor circuit is shorted.
Intake Air Temp (Turbo)
Intake air temperature after intercooler
If -40°C (-40°F), the sensor circuit is open.
If 190°C (374°F) or higher, the sensor circuit is shorted.
Engine Run Time
Accumulated engine running time
-
Initial Engine Coolant Temp
Engine coolant temperature at engine start
-
Initial Intake Air Temp
Intake air temperature at engine start
-
Battery Voltage
Battery voltage
-
Glow Control Unit Duty
Glow control unit duty
-
Eng Oil Press Switch Valve
Engine oil pressure switching valve status
-
Engine Oil Pressure
Engine oil pressure
-
Accel Position
Accelerator pedal position sensor
-
Accel Sens. No.1 Volt %
Accelerator pedal position No. 1 output voltage
-
Accel Sens. No.2 Volt %
Accelerator pedal position No. 2 output voltage
-
Target Throttle Position
Target throttle position
-
Actual Throttle Position
Actual throttle position
-
Diesel Throttle Learn Status
Diesel throttle learning status
-
Throttle Sensor Volt %
Throttle position sensor output voltage
-
Throttle Motor DUTY
Throttle actuator
-
Injection Volume
Injection volume
-
Inj. FB Vol. for Idle
Injection feedback value for idle speed control
-
Inj Vol Feedback Learning
Injection volume feedback learned value
-
Injection Feedback Val #1
Injection volume correction for cylinder 1
-
Injection Feedback Val #2
Injection volume correction for cylinder 2
-
Injection Feedback Val #3
Injection volume correction for cylinder 3
-
Injection Feedback Val #4
Injection volume correction for cylinder 4
-
Pilot 1 Injection Period
Pilot 1 injection period
-
Pilot 2 Injection Period
Pilot 2 injection period
-
Main Injection Period
Main injection period
-
After Injection Period
Post injection period
-
Pilot 1 Injection Timing
Pilot 1 injection timing
-
Pilot 2 Injection Timing
Pilot 2 injection timing
-
Main Injection Timing
Main injection timing
-
After Injection Timing
Post injection timing
-
Injector Memory Error
State of injector related EEPROM information stored in ECM
This item is used for troubleshooting when DTC P062F is stored.
Reju Pilot Quantity Learning
Pilot quantity learning prohibition
The status is only displayed while performing "Pilot Quantity Learning".
Pilot Quantity Learning
Pilot quantity learning status
The status is only displayed while performing "Pilot Quantity Learning".
Target Common Rail Pressure
Target common rail pressure
-
Fuel Press
Fuel pressure
-
Fuel Temperature
Fuel temperature
-
Fuel Return Temp
Fuel return temperature
-
Target Pump SCV Current
Final pump current target value
-
Pump SCV Learning Value
Pump current learned value
-
Pressure Discharge Valve
Pressure discharge valve operation prohibition
-
AF Lambda B1S1
Lambda equivalent ratio
-
AFS Voltage B1S1
Air fuel ratio sensor output voltage
Performing control the injection volume or control the injection volume for air fuel ratio sensor function of Active Test enables technician to check output voltage of sensor
AFS Current B1S1
Air fuel ratio sensor output current
-
Target EGR Position
Target EGR valve position
-
Actual EGR Valve Pos.
Actual EGR valve position
-
EGR Motor Duty #1
EGR motor duty ratio
-
EGR Close Lrn. Val.
EGR valve fully closed position learned value
-
EGR Close Lrn. Status
EGR valve fully closed position learning status
-
EGR Operation Prohibit
EGR operation prohibition
-
EGR Cooler Bypass VSV
Vacuum switching valve (for No. 1 EGR bypass valve) status
-
EGR Cooler Bypass VSV2
Vacuum switching valve (for No. 2 EGR bypass valve) status
-
EGR Cooler Bypass Position
EGR cooler bypass position
-
Target Booster Pressure
Target booster pressure
-
VN Turbo Command
VN turbo command
-
Actual VN Position
Actual VN turbo position
-
VN Position Sensor Out
VN position sensor output voltage
-
VN Motor Duty
VN turbo motor duty
-
VN Close Learn Value
VN turbo fully closed position learned value
-
VN Close Learn Status
VN turbo fully closed position learning status
-
Exhaust Temperature B1S1 Supported
Status of the Exhaust Temperature B1S1 Supported
-
Exhaust Temperature B1S1
Exhaust temperature sensor (B1S1)
If -40°C (-40°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
Exhaust Temperature B1S2 Supported
Status of the Exhaust Temperature B1S2 Supported
-
Exhaust Temperature B1S2
No. 2 exhaust temperature sensor (B1S2)
If -40°C (-40°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
Exhaust Temperature B1S3 Supported
Status of the Exhaust Temperature B1S3 Supported
-
Exhaust Temperature B1S3
No. 3 exhaust temperature sensor (B1S3)
If -40°C (-40°F), sensor circuit is open
If 1000°C (1832°F) or more, sensor circuit is shorted
DPF Differential Pressure
DPF differential pressure
-
Catalyst Differential Press
Standardized DPF differential pressure
-
Exhaust Fuel Addition FB
Exhaust fuel addition correction value
-
DPF Thermal Deteriorate
DPF thermal deterioration
-
DPF No Activate
DPF operation
-
DPF PM Block
DPF PM block
-
Catalyst Memory Error
EEPROM malfunction for catalyst
This item is used for troubleshooting when DTC P062F is stored.
Add. INJ Flow Excessive
Excessive flow malfunction of exhaust addition injector
-
DPF Over temperature
Over temperature malfunction
-
PM Accumulation Ratio
PM accumulation ratio
-
Starter Signal
Starter signal
-
Power Steering Signal
Power steering switch status
-
Power Steer. Sig. Record
Power steering switch status history
-
Neutral Position SW Signal
Neutral position switch signal
-
Clutch Switch
Clutch switch
-
Reverse Switch
-
-
Stop Light Switch
Stop light switch
-
A/C Signal
Air conditioning signal
-
Immobiliser Communication
Immobiliser communication
-
Time after DTC Cleared
Cumulative time after DTC cleared
-
Distance from DTC Cleared
Accumulated distance after DTC cleared
-
Warmup Cycle Cleared DTC
Warmup cycles after DTC cleared
-
TC and TE1
TC and TE1 terminals of DLC3
-
Engine Start Time
-
This item is used for troubleshooting when DTC P1604 is stored.
Engine Speed (Starter Off)
-
This item is used for troubleshooting when DTC P1604 is stored.
Starter Count
-
This item is used for troubleshooting when DTC P1604 is stored.
Run Dist of Previous Trip
-
This item is used for troubleshooting when DTC P1604 is stored.
Glow Request Lighting Time
Glow request lighting time
This item is used for troubleshooting when DTC P1604 is stored.
IG-ON Time
Engine switch on (IG) time before engine start
This item is used for troubleshooting when DTC P1604 is stored.
MAF Low
Mass air flow low
This item is used for troubleshooting when DTC P1608 is stored.
Boost Pressure Low
Boost pressure low
This item is used for troubleshooting when DTC P1608 is stored.
Common Rail Pressure Low
Common rail pressure low
This item is used for troubleshooting when DTC P1608 is stored.
Engine Coolant Temp High
Engine coolant temperature high
This item is used for troubleshooting when DTC P1608 is stored.
MAF/Estimate MAF Ratio
Indicates the ratio of estimated intake air volume and the actual intake air volume
This item is used for troubleshooting when DTC P1608 is stored.
Rough Idle #1
Rough idle status of cylinder 1
This item is used for troubleshooting when DTC P1605 is stored.
Rough Idle #2
Rough idle status of cylinder 2
This item is used for troubleshooting when DTC P1605 is stored.
Rough Idle #3
Rough idle status of cylinder 3
This item is used for troubleshooting when DTC P1605 is stored.
Rough Idle #4
Rough idle status of cylinder 4
This item is used for troubleshooting when DTC P1605 is stored.
Electric Duty Feedback Value
Electric load feedback value
-
A/C Duty Feedback Value
A/C load feedback value
-
PS Duty Feedback Value
Power steering load feedback value
-
Idle Injection Volume (Min)
Idle minimum injection volume
-
ACM Inhibit
VSV for engine mount status
-
Swirl Control Valve VSV
VSV for swirl control valve
-
ACT VSV
A/C cut status for Active Test
-
Electric Fan Motor
Electric fan motor
-
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut history
-
Received MIL from ECT
MIL status from ECT
-
Shift Position Sig from ECT
Shift position from ECT
-
A/T Oil Temp from ECT
ATF temperature from ECT
-
SPD (NO)
Output shaft speed
-
ECT Lock Up
ECT lock-up status
-
← DTC CHECK / CLEAR (from Aug 2014)CHECK MODE PROCEDURE (from Aug 2013) →