2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

P0115 Engine Coolant Temperature Circuit

Diagnostic trouble codes · Vehicles built from Aug 2013

Also covers:

DESCRIPTION

A thermistor, whose resistance value varies according to the engine coolant temperature, is built into the engine coolant temperature sensor. The connection between the engine coolant temperature sensor and the ECM is the same as that of the intake air temperature sensor.
DTC No.
DTC Detection Condition
Trouble Area
P0115
An open or short in the engine coolant temperature sensor circuit for 0.5 seconds (1-trip detection logic).
  1. Open or short in engine coolant temperature sensor circuit
  2. Engine coolant temperature sensor
  3. ECM
P0117
A short in the engine coolant temperature sensor circuit for 0.5 seconds (1-trip detection logic).
  1. Short in engine coolant temperature sensor circuit
  2. Engine coolant temperature sensor
  3. ECM
P0118
An open in the engine coolant temperature sensor circuit for 0.5 seconds (1-trip detection logic).
  1. Open in engine coolant temperature sensor circuit
  2. Engine coolant temperature sensor
  3. ECM

HINT:
When any of these DTCs are output, check the engine coolant temperature using the intelligent tester. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

Temperature Displayed
Malfunction
-40°C (-40°F)
Open circuit
140°C (284°F)
Short circuit

WIRING DIAGRAM

A162760E31

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the tester.

    Result 
    Result
    Proceed to
    Temperature displayed is -40°C (-40°F)
    A
    Temperature displayed is 140°C (284°F)
    B
    Temperature displayed is between 80°C and 100°C (176°F and 212°F)
    C

    HINT:
    1. If there is an open circuit, the intelligent tester indicates -40°C (-40°F).
    2. If there is a short circuit, the intelligent tester indicates 140°C (284°F).



B
Go to step 4

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A208643E04
    Confirm that there is a good connection at the engine coolant temperature sensor.

  1. Disconnect the engine coolant temperature sensor connector.

  1. Connect terminals 1 and 2 of the wire harness connector for the engine coolant temperature sensor.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the tester.

    Standard value:
    140°C (284°F)

    Text in Illustration 
    *1
    Engine Coolant Temperature Sensor
    *2
    ECM
    *a
    Front view of wire harness connector
    (to Engine Coolant Temperature Sensor)

  1. Reconnect the engine coolant temperature sensor connector.



NG
Go to step 3
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)

3. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C24-2 - C61-18 (THW)
    Always
    Below 1 Ω
    C24-1 - C61-17 (ETHW)
    Always
    Below 1 Ω

  1. Reconnect the engine coolant temperature sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
OK

REPLACE ECM (Click here)

4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A211723E02
    Disconnect the engine coolant temperature sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Coolant Temp.

  1. Read the value displayed on the tester.

    Standard value:
    -40°C (-40°F)

    Text in Illustration 
    *1
    Engine Coolant Temperature Sensor
    *2
    ECM

  1. Reconnect the engine coolant temperature sensor connector.



NG
Go to step 5
OK

REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)

5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
  1. Disconnect the engine coolant temperature sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C24-2 or C61-18 (THW) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the engine coolant temperature sensor connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)
OK

REPLACE ECM (Click here)


← P0112 Intake Air Temperature Circuit Low Input (+ P0113) (from Aug 2013)P0116 Engine Coolant Temperature Circuit Range / Performance (Aug 2013 – Jul 2014) →