P0327 Knock Sensor 1 Circuit Low Input (Bank 1 or Single Sensor)
Diagnostic trouble codes · Vehicles built from Aug 2013
Also covers:
- P0328 Knock Sensor 1 Circuit High Input (Bank 1 or Single Sensor)
DESCRIPTION
Flat-type knock sensors (non-resonant type) have structures that can detect vibrations between approximately 5 kHz and 15 kHz.The knock sensor is fitted onto the engine block to detect engine knocking.
The knock sensor contains a piezoelectric element which generates a voltage when it becomes deformed.
The voltage is generated when the engine block vibrates due to knocking. Any occurrence of engine knocking can be suppressed by delaying the ignition timing.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0327 |
The output voltage of the knock sensor is below 0.5 V (1 trip detection logic). |
|
| P0328 |
The output voltage of the knock sensor is higher than 4.5 V (1 trip detection logic). |
|
- HINT:
- When DTC P0327 or P0328 is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is delayed to its maximum retardation. The ECM continues operating in fail-safe mode until the ignition switch is turned off.


The correct waveform is as shown.
| Item |
Content |
| ECM Terminal Name |
KNK1 - EKNK |
| Tester Range |
1 V/DIV., 1 ms./DIV. |
| Condition |
Engine speed maintained at 4000 rpm after engine warmed up |
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. READ VALUE USING INTELLIGENT TESTER (KNOCK FEEDBACK VALUE) |
Connect the intelligent tester to the DLC3.
Start the engine.
Turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine and ECT / Data List / Knock Feedback Value.
Read the values displayed on the tester while the vehicle is being driven.
- OK:
- The values change.
- HINT:
Malfunction does not occur
Knock feedback values change
Malfunction occurs
Knock feedback values do not change
- The Knock Feedback Value change can be confirmed by running the engine with a high load, for example, by activating the air conditioning system and racing the engine.
|
|
||||
| OK | ||
| ||
| 2. INSPECT ECM (KNK1 VOLTAGE) |
Disconnect the knock sensor connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
h3-2 - h3-1
Ignition switch ON
4.5 to 5.5 V
Text in Illustration *a
Front view of wire harness connector
(to Knock Sensor)
Reconnect the knock sensor connector.
|
|
||||
| OK | |
| 3. INSPECT KNOCK SENSOR |
Inspect the knock sensor (Click here).
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (ECM - KNOCK SENSOR) |
Disconnect the knock sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
h3-2 - C61-6 (KNK1)
Always
Below 1 Ω
h3-1 - C61-5 (EKNK)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
h3-2 or C61-6 (KNK1) - Body ground
Always
10 kΩ or higher
h3-1 or C61-5 (EKNK) - Body ground
Always
10 kΩ or higher
Reconnect the knock sensor connector.
Reconnect the ECM connector.
|
|
||||
| OK | ||
| ||
