DATA LIST / ACTIVE TEST
System information · Vehicles built from Aug 2013
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Vehicle Speed
Vehicle speed/
Min.: 0 km/h, Max.: 255 km/h
Actual vehicle speed
The speed indicated on the speedometer.
Engine Speed
Engine speed/
Min.: 0 rpm, Max.: 16383 rpm
600 to 700 rpm: Idling
-
Calculated Load
Lode calculated by ECM/
Min.: 0%, Max.: 100%
- 10 to 30%: Idling
- 10 to 40%: Running without load (3000 rpm)
-
Vehicle Load
Vehicle load/
Min.: 0%, Max.: 25700%
Actual vehicle load
-
MAF
Air flow rate from MAF meter/
Min.: 0 gm/s, Max.: 655.35 gm/s
1.0 to 4.0 gm/s: Idling
If the value is approximately 0.0 gm/s: - The mass air flow meter power source circuit is open.
- The VG circuit is open or shorted.
- The E2G circuit is open.
Atmosphere Pressure
Atmospheric pressure/
Min.: 0 kPa, Max.: 255 kPa
Equivalent to atmospheric pressure (absolute pressure)
-
Coolant Temp
Engine coolant temperature/
Min.: -40°C, Max.: 215°C
80 to 100°C (176 to 212°F): After warming up
- If the value is -40°C (-40°F): the sensor circuit is open.
- If the value is 140°C (284°F): the sensor circuit is shorted.
Intake Air
Intake air temperature/
Min.: -40°C, Max.: 140°C
Equivalent to ambient air temperature
- If the value is -40°C (-40°F): the sensor circuit is open.
- If the value is 140°C (284°F): the sensor circuit is shorted.
Engine Run Time
Engine run time/
Min.: 0 s, Max.: 65535 s
Time after engine start
Service data.
Initial Engine Coolant Temp
Initial engine coolant temperature/
Min.: -40°C, Max.: 119.3°C
Engine coolant temperature when engine started
Service data.
Initial Intake Air Temp
Initial intake air temperature/
Min.: -40°C, Max.: 119.3°C
Intake air temperature when engine started
Service data.
Battery Voltage
Battery voltage/
Min.: 0 V, Max.: 65.535 V
11 to 14 V: Idling
-
Accelerator Position
Accelerator pedal position/
Min.: 0%, Max.: 399.9%
Actual accelerator pedal position
-
Accel Sens. No.1 Volt %
Absolute No. 1 accelerator pedal position/
Min.: 0%, Max.: 100%
- 10 to 22%: Accelerator pedal released
- 52 to 90%: Accelerator pedal fully depressed
-
Accel Sens. No.2 Volt %
Absolute No. 2 accelerator pedal position/
Min.: 0%, Max.: 100%
- 24 to 40%: Accelerator pedal released
- 68 to 95%: Accelerator pedal fully depressed
-
Accel Sensor Out No.1
No. 1 accelerator pedal position sensor voltage/
Min.: 0 V, Max.: 4.98 V
- 0.5 to 1.1 V: Accelerator pedal released
- 2.6 to 4.5 V: Accelerator pedal fully depressed
-
Accel Sensor Out No.2
No. 2 accelerator pedal position sensor voltage/
Min.: 0 V, Max.: 4.98 V
- 1.2 to 2.0 V: Accelerator pedal released
- 3.4 to 4.75 V: Accelerator pedal fully depressed
-
Accelerator Idle Position
Whether or not accelerator pedal position sensor detecting idle/
ON or OFF
ON: Idling
-
Accel Fully Close Learn #1
Accelerator fully closed learning value No. 1/
Min.: 0 deg, Max.: 124.5 deg
-
ETCS service data.
Accel Fully Close Learn #2
Accelerator fully closed learning value No. 2/
Min.: 0 deg, Max.: 124.5 deg
-
ETCS service data.
Throttle Sensor Volt %
Throttle sensor positioning/
Min.: 0% Max.: 100%
- 10 to 22%: Accelerator pedal released
- 64 to 96%: Accelerator pedal fully depressed
A calculated value based on VTA1.
Throttle Sensor #2 Volt %
Throttle sensor positioning #2/
Min.: 0%, Max.: 100%
- 42 to 62%: Accelerator pedal released
- 92 to 100%: Accelerator pedal fully depressed
A calculated value based on VTA2.
ST1
Brake pedal signal/
ON or OFF
ON: Brake pedal depressed
-
System Guard
System guard/
ON or OFF
-
ETCS service data.
Open Side Malfunction
Open side malfunction/
ON or OFF
-
ETCS service data.
Throttle Idle Position
Whether or not throttle position sensor detecting idle/
ON or OFF
- ON: Accelerator pedal released
- OFF: Accelerator pedal depressed
-
Throttle Require Position
Required throttle position/
Min.: 0 V, Max.: 4.98 V
0.5 to 1.1 V: Idling
-
Throttle Sensor Position*
Throttle sensor position/
Min.: 0%, Max.: 100%
- 0%: Accelerator pedal released
- 50 to 80%: Accelerator pedal fully depressed
Value for the recognition of the throttle opening angle for the ECM.
Throttle Position No. 1
No. 1 throttle position/
Min.: 0 V, Max.: 4.98 V
- 0.5 to 1.1 V: Accelerator pedal released
- 3.2 to 4.8 V: Accelerator pedal fully depressed
- 0.6 to 1.4 V: Fail-safe operating
-
Throttle Position No. 2
No. 2 throttle position/
Min.: 0 V, Max.: 4.98 V
- 2.1 to 3.1 V: Accelerator pedal released
- 4.6 to 4.98 V: Accelerator pedal fully depressed
- 2.1 to 3.1 V: Fail-safe operating
-
Throttle Position Command
Throttle position command value/
Min.: 0 V, Max.: 4.98 V
0.5 to 4.8 V
-
Throttle Sens Open Pos#1
Throttle position sensor No. 1/
Min.: 0 V, Max.: 4.98 V
0.6 to 1.4 V
ETCS service data.
Throttle Sens Open Pos#2
Throttle position sensor No. 2/
Min.: 0 V, Max.: 4.98 V
1.7 to 2.5 V
ETCS service data.
Throttle Motor Current
Throttle actuator current/
Min.: 0 A, Max.: 19.9 A
0 to 3.0 A: Idling
ETCS service data.
Throttle Motor DUTY
Throttle actuator/
Min.: 0% Max.: 100%
10 to 22%: Idling after engine warmed up
ETCS service data.
Throttle Motor Duty (Open)
Throttle motor duty ratio (open)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
ETCS service data.
Throttle Motor Duty (Close)
Throttle motor duty ratio (close)/
Min.: 0%, Max.: 255%
0 to 40%: Idling
ETCS service data.
Throttle Fully Close Learn
Throttle valve fully closed learned value/
Min.: 0 V, Max.: 4.98 V
0.4 to 1.0 V: Accelerator pedal released
-
+BM Voltage
+BM voltage/
Min.: 0, Max.: 79.998 V
11 to 14 V: Ignition switch ON and system normal
ETCS service data.
Actuator Power Supply
Actuator power supply/
ON or OFF
- ON: Ignition switch ON and system normal
- OFF: ETCS has failed
ETCS service data.
Throttle Position
Throttle valve opening angle/
Min.: 0 deg, Max.: 499.99 deg
-
For use when engine stall, starting problems or rough idle is present.
ISC Flow
Flow rate calculated using information from each sensor/
Min.: 0 L/s, Max.: 79.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
ISC Position
Requested opening amount calculated using ISC control/
Min.: 0 deg, Max.: 499.99 deg
-
This is the throttle valve opening amount while the engine is idling (the throttle valve opening amount necessary to maintain ISC air flow).
ISC Feedback Value
ISC feedback compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
ISC Learning Value
ISC learned compensation amount/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Electric Load Feedback Val
Compensation flow rate according to electrical load/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Air Conditioner FB Val
Compensation flow rate according to air conditioner load/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
PS Feedback Val
Compensation flow rate according to power steering load/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Low Revolution Control
Low engine speed control operation state/
ON or OFF
-
For use when engine stall, starting problems or rough idle is present.
N Range Status
Shift lever N status/
ON or OFF
-
For use when engine stall, starting problems or rough idle is present.
Eng Stall Control FB Flow
Intake air compensation flow rate/
Min.: -40 L/s, Max.: 39.99 L/s
-
For use when engine stall, starting problems or rough idle is present.
Injector (Port)
Injection period of No. 1 cylinder/
Min.: 0 μs, Max.: 65535 μs
1800 to 3800 μs: Idling
-
Injection Volume (Cylinder 1)
Injection volume (cylinder 1)/
Min.: 0 ml, Max.: 2.047 ml
0 to 0.5 ml: Idling
The fuel injection volume for 10 injections.
Fuel Pump/Speed Status
Fuel pump status/
ON or OFF
-
Active Test support data.
Current Fuel Type
Status of the current fuel type
Gasoline/petrol
-
EVAP (Purge) VSV
EVAP (Purge) VSV control duty/
Min.: 0%, Max.: 100%
0 to 100%: During idling
A command signal from the ECM.
EVAP Purge Flow
Purge flow/
Min.: 0%, Max.: 399.9%
0 to 100%: Idling
-
Purge Destiny Learn Value
Purge density learned value/
Min.: -200, Max.: 199.993
-40 to 1: Idling
Service data.
EVAP Purge VSV
VSV status for EVAP control/
ON or OFF
-
Active Test support data.
Purge Cut VSV Duty
Purge cut VSV duty/
Min.: 0%, Max.: 399.9%
-
-
Target Air-Fuel Ratio
Target air fuel ratio/
Min.: 0, Max.: 1.99
0.8 to 1.2: Idling
-
AF Lambda B1S1
Short-term fuel trim/
Min.: 0, Max.: 1.99
- Value less than 1 (0.000 to 0.999) = Rich
- Stoichiometric air-fuel ratio = 1
- Value more than 1 (1.001 to 1.999) = Lean
-
AFS Voltage B1S1
Air fuel ratio sensor output voltage/
Min.: 0 V, Max.: 7.99 V
3.0 to 3.5 V: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
AFS Current B1S1
Air fuel ratio sensor current/
Min.: -128 mA, Max.: 127.99 mA
-0.5 to 0.5 mA: Idling
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
A/F Heater Duty #1
Air fuel ratio sensor heater duty ratio/
Min.: 0%, Max.: 399.9%
0 to 100%
-
O2S B1S2
Heated oxygen sensor output voltage for bank 1 sensor 2/
Min.: 0 V, Max.: 1.275 V
0 to 1.0 V: Driving at 70 km/h (44 mph)
Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output current of the sensor.
O2 Heater B1S2
Heated oxygen sensor heater/
Active or Not Act
-
-
O2 Heater Curr Val B1S2
Heated oxygen sensor current/
Min.: 0 A, Max.: 4.999 A
-
-
Short FT #1
Short-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-20 to +20%
Short-term fuel compensation used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio.
Long FT #1
Long-term fuel trim of bank 1/
Min.: -100%, Max.: 99.2%
-20 to +20%
Overall fuel compensation carried out in the long term to compensate for a continual deviation of the short-term fuel trim from the central value.
Total FT #1
Total fuel trim of bank 1/
Min.: -0.5, Max.: 0.496
-0.2 to 0.2: Idling
-
Fuel System Status #1
Fuel system status (Bank 1)/
OL or CL or OLDrive or OLFault or CLFault
CL: Idling after warming up
- OL (Open Loop): Has not yet satisfied the conditions to go to closed loop.
- CL (Closed Loop): Using the heated oxygen sensor as feedback for fuel control.
- OLDrive: Open loop due to driving conditions (fuel enrichment).
- OLFault: Open loop due to a detected system fault.
- CLFault: Closed loop but the heated oxygen sensor, which is used for fuel control, is malfunctioning.
Fuel System Status #2
Fuel system status (Bank 2)/
OL or CL or OLDrive or OLFault or CLFault
-
-
Air Pump Pressure (Absolute)
Air pump pressure (absolute)/
Min.: 0 kPa, Max.: 65535 kPa
- Atmospheric pressure +1 kPa or more: Air pump on, air switching valve open
- Close to atmospheric pressure: Air pump off, air switching valve closed
-
Air Pump Pulsation Pressure
Air pump pulsation pressure/
Min.: 0 kPa, Max.: 655.35 kPa
-
Cumulative pulsation pressure calculated by ECM
Secondary Air Control VSV
Secondary air injection system status/
ON or OFF
ON: Secondary air injection system operating
-
2nd Air System Status
Secondary air injection system status/
ON or OFF
ON: Secondary air system operating
-
AI Test
Secondary air injection system operation prohibition/
READY or NOT RDY
-
-
IGN Advance
Ignition timing advance for No. 1 cylinder/
Min.: -64 deg., Max.: 63.5 deg
BTDC 0 to 20°: Idling
-
Knock Feedback Value
Knocking feedback value/
Min.: -1024 deg(CA), Max.: 1023.9 deg(CA)
-20 to 0 deg(CA)
Driving, 44 mph (70 km/h)
Service data.
Knock Correct Learn Value
Knocking correction learned value/
Min.: -1024 deg(CA), Max.: 1023.9 deg(CA)
0 to 20°CA:
Driving, 44 mph (70 km/h)
Service data.
Idle Spark Advn Ctrl #1
Individual cylinder timing advance compensation amount (No. 1)/
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #2
Individual cylinder timing advance compensation amount (No. 2)/
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #3
Individual cylinder timing advance compensation amount (No. 3)/
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
-
For use when engine stall, starting problems or rough idle is present.
Idle Spark Advn Ctrl #4
Individual cylinder timing advance compensation amount (No. 4)/
Min.: 0 deg(CA), Max.: 15.93 deg(CA)
-
For use when engine stall, starting problems or rough idle is present.
VVT Control Status #1
VVT control status/
ON or OFF
-
Active Test support data.
VVT Advance Fail
VVT control failure status/
ON or OFF
ON: VVT control failure
-
VVT Aim Angle #1
VVT target angle/
Min.: 0%, Max.: 399.9%
0%: Idling
The VVT duty signal value during the forced operation.
VVT Change Angle #1
VVT displacement angle/
Min.: 0 DegFR, Max.: 639.9 DegFR
0 to 5 DegFR: Idling
The displacement angle during the forced operation.
VVT OCV Duty #1
VVT OCV operation duty/
Min.: 0%, Max.: 399.9%
0%: Idling
The requested duty value for the forced operation.
VN Turbo Type
VN turbo type/
Not Avl, Commo, Vacuum or CAN Com
-
-
Catalyst Temp B1S1
Catalyst temperature (Bank 1, Sensor 1)/
Min.: -40°C, Max.: 6513.5°C
-
-
Catalyst Temp B1S2
Catalyst temperature (Bank 1, Sensor 2)/
Min.: -40°C, Max.: 6513.5°C
-
-
Starter Signal
Starter signal/
ON or OFF
ON: Cranking
-
Power Steering Signal
Power steering switch signal/
ON or OFF
ON: Power steering operating
-
Neutral Position SW Signal
PNP switch status/
ON or OFF
ON: P or N position
-
Clutch Switch
Clutch switch status/
ON or OFF
ON: Clutch switch on
-
Clutch Start SW
Clutch start switch status/
ON or OFF
ON: Clutch start switch on
-
Transfer L4
L4 status of the transfer/
ON or OFF
ON: 4WD control switch in 4L position
-
Stop Light Switch
Stop light switch/
ON or OFF
ON: Brake pedal depressed
-
A/C Signal
A/C switch status/
ON or OFF
ON: A/C on
-
Closed Throttle Position SW
Closed throttle position switch/
ON or OFF
- ON: Throttle fully closed
- OFF: Throttle open
-
Fuel Cut Condition
Fuel cut condition/
ON or OFF
ON: Fuel cut operating
-
Immobiliser Communication
Immobiliser communication/
ON or OFF
ON: Normal
-
Check Mode
Check mode/
ON or OFF
ON: Check mode on
Refer to Check Mode Procedure (Click here).
SPD Test Result
Check mode result for vehicle speed sensor/
Compl or Incmpl
-
-
AS Test Result
Check mode result for secondary air injection system/
Compl or Incmpl
-
-
Misfire Test Result
Check mode result for misfire monitor/
Compl or Incmpl
-
-
OXS1 Test Result
Check mode result for heated oxygen sensor (Bank 1)/
Compl or Incmpl
-
-
A/F Test Results #1
Check mode result for air fuel ratio sensor (Bank 1)/
Compl or Incmpl
-
-
Complete Parts Monitor
Comprehensive component monitor/
Not Avl or Avail
-
-
Fuel System Monitor
Fuel system monitor/
Not Avl or Avail
-
-
Misfire Monitor
Misfire monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor/
Not Avl or Avail
-
-
EGR/VVT Monitor
EGR/VVT monitor/
Compl or Incmpl
-
-
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Not Avl or Avail
-
-
O2S(A/FS) Heater Monitor
O2S (A/FS) heater monitor/
Compl or Incmpl
-
-
O2S(A/FS) Monitor
O2S (A/FS) heater monitor/
Not Avl or Avail
-
-
O2S(A/FS) Monitor
O2S (A/FS) heater monitor/
Compl or Incmpl
-
-
A/C Monitor
A/C monitor/
Not Avl or Avail
-
-
A/C Monitor
A/C monitor/
Compl or Incmpl
-
-
2nd Air Monitor
2nd air monitor/
Not Avl or Avail
-
-
2nd Air Monitor
2nd air monitor/
Compl or Incmpl
-
-
EVAP Monitor
EVAP monitor/
Not Avl or Avail
-
-
EVAP Monitor
EVAP monitor/
Compl or Incmpl
-
-
Heated Catalyst Monitor
Heated catalyst monitor/
Not Avl or Avail
-
-
Heated Catalyst Monitor
Heated catalyst monitor/
Compl or Incmpl
-
-
Catalyst Monitor
Catalyst monitor/
Not Avl or Avail
-
-
Catalyst Monitor
Catalyst monitor/
Compl or Incmpl
-
-
TC Terminal
TC terminal status/
ON or OFF
-
-
# Codes (Include History)
Number of codes/
Min.: 0, Max.: 255
-
Number of stored DTCs.
MIL
MIL status/
ON or OFF
ON: MIL on
-
MIL ON Run Distance
Distance driven after MIL turns on/
Min.: 0 km, Max.: 65535 km
Distance driven after DTC stored
-
Running Time from MIL ON
Running time after MIL turned on/
Min.: 0 min, Max.: 65535 min
Running time after MIL turned on
-
Time after DTC Cleared
Time after DTC cleared/
Min.: 0 min, Max.: 65535 min
Time after DTCs cleared
-
Distance from DTC Cleared
Distance driven after DTC cleared/
Min.: 0 km, Max.: 65535 km
Driving distance after DTCs cleared
-
Warmup Cycle Cleared DTC
Warmup cycles after DTC cleared/
Min.: 0, Max.: 255
-
The number of warmup cycles after the DTCs were cleared.
Dist Batt Cable Disconnect
Distance driven after battery cable disconnected/
Min.: 0 km, Max.: 65535 km
Total distance vehicle driven after battery cable disconnected
-
OBD Requirements
OBD requirement
EOBD (Euro OBD)
-
Number of Emission DTC
Emissions-related DTCs
-
The number of emissions-related DTCs.
TC and TE1
TC and CG (TE1) terminals of DLC3/
ON or OFF
-
-
Ignition Trig. Count
Ignition counter/
Min.: 0, Max.: 65535
0 to 400
-
Cylinder #1 Misfire Count
Misfire count of cylinder 1/
Min.: 0, Max.: 255
0
-
Cylinder #2 Misfire Count
Misfire count of cylinder 2/
Min.: 0, Max.: 255
0
-
Cylinder #3 Misfire Count
Misfire count of cylinder 3/
Min.: 0, Max.: 255
0
-
Cylinder #4 Misfire Count
Misfire count of cylinder 4/
Min.: 0, Max.: 255
0
-
All Cylinders Misfire Count
Misfire count of all cylinders/
Min.: 0, Max.: 255
0 to 35
-
Misfire RPM
Engine speed for first misfire range/
Min.: 0 rpm, Max.: 6375 rpm
0 rpm: 0 misfires
-
Misfire Load
Engine load for first misfire range/
Min.: 0 g/rev, Max.: 3.98 g/rev
0 g/rev: 0 misfires
-
Misfire Margin
Misfire monitoring/
Min.: -128%, Max.: 127%
0 to 99.2%
Misfire detecting margin.
Engine Speed (Starter Off)
Engine speed when starter off/
Min.: 0 rpm, Max.: 51199 rpm
-
For use when engine stall, starting problems or rough idle is present.
Starter Count
Number of times starter turned on after ignition switch turned to ON/
Min.: 0, Max.: 255
-
For use when engine stall, starting problems or rough idle is present.
Run Dist of Previous Trip
Distance driven during previous trip/
Min.: 0 km, Max.: 655.35 km
-
Before 5 seconds elapse after starting the engine, which is DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal. - HINT:
- Run Dist of Previous Trip in freeze frame data which were present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of Data List (real-time measurements), or for freeze frame data which were present when the DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.
Engine Starting Time
Time elapsed after engine started (interval between ignition switch ON and off)/
Min.: 0 ms, Max.: 655350 ms
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Coolant Temp
Engine coolant temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Intake Temp
Intake air temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Engine Oil Temperature
Engine oil temperature (estimated temperature)/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Eng Oil Temp
Engine oil temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Ambient Temp for A/C
Ambient temperature for A/C/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Previous Trip Ambient Temp
Ambient temperature during previous trip/
Min.: -40°C, Max.: 215°C
-
For use when engine stall, starting problems or rough idle is present.
Engine Start Hesitation
History of hesitation during engine start/
ON or OFF
-
-
Low Rev for Eng Start
History of low engine speed after engine start/
ON or OFF
-
-
Minimum Engine Speed
Minimum engine speed/
Min.: 0 rpm, Max.: 51199 rpm
-
For use when engine stall, starting problems or rough idle is present.
Fuel Cut Elps Time
Time elapsed after engine runs at high speed/
Min.: 0 sec, Max.: 68746 sec
-
-
ACT VSV
A/C cut status for Active Test/
ON or OFF
-
Active Test support data.
Brake Override System
Brake Override System Status/
ON or OFF
ON: Brake override system operation
-
Idle Fuel Cut
Fuel cut at idle/
ON or OFF
ON: Fuel cut operating
Idle Fuel Cut is "ON" when the throttle valve fully is closed and the engine speed is over 2800 rpm.
FC TAU
Fuel cut TAU (Fuel cut during very light load)/
ON or OFF
ON: Fuel cut operating
Fuel cut is being performed under a very light load to prevent the engine combustion from becoming incomplete.
Immobiliser Fuel Cut
Status of the immobiliser fuel cut/
ON or OFF
-
-
Immobiliser Fuel Cut History
Status of the immobiliser fuel cut history/
ON or OFF
-
-
Comm with Power Manage
Status of communication with the power management control ECU/
Comm or No Comm
-
-
Comm with Air Conditioner
Status of communication with the air conditioning amplifier assembly/
Comm or No Comm
-
-
Electrical Load Signal 1
Electrical load signal/
ON or OFF
-
-
Electrical Load Signal 2
Electrical load signal/
ON or OFF
-
-
Cruise Cancel Signal
Status of the cruise cancel signal/
ON or OFF
-
-
Model Code
Model code
-
Used for identifying model code: TRJ15#
Engine Type
Engine type
-
Used for identifying engine type: 2TRFE
Cylinder Number
Number of cylinders/
Min.: 0, Max.: 255
-
Used for identifying number of cylinders: 4
Transmission Type
Transmission type
-
Used for identifying the transmission type: MT or ECT(4AT)
Destination
Destination
-
Used for identifying the destination:
W
Model Year
Model year/
Min.: 1900, Max.: 2155
-
Used for identifying the model year: 20##
System Identification
System identification
-
Used for identifying the engine system: Gasoline (gasoline engine)
Engine Speed of Cyl #1
Engine speed for cylinder 1/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #2
Engine speed for cylinder 2/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #3
Engine speed for cylinder 3/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Engine Speed of Cyl #4
Engine speed for cylinder 4/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Av Engine Speed of All Cyl
Engine speed for all cylinders/
Min.: 0 rpm, Max.: 51199 rpm
-
Output only when Check the Cylinder Compression is performed using the Active Test.
Kick Down Switch Status
Kick down switch status/
ON or OFF
-
-
- 10 to 30%: Idling
- HINT:
- *: This excludes the throttle valve opening percentage due to Idle Speed Control (ISC).
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time.
- Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester ON.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on tester, perform the "Active Test".
Tester Display
Test Part
Control Range
Diagnostic Notes
Control the Injection Volume
Change injection volume
Between -12% and 24.8%
- All the injectors are tested at the same time.
- Perform the test at less than 3000 rpm.
- The injection volume can be changed in 1% gradations within the control range.
Control the Injection Volume for A/F Sensor
Change injection volume
-12.5% / 0% / 12.5%
- Perform the test at less than 3000 rpm.
- Control the Injection Volume for the A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor and Heated Oxygen (HO2) sensor voltage outputs.
- To conduct the test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / Data List / A/ F Control System / AFS Voltage B1S1 and O2S B1S2.
Activate the VSV for Secondary Air Control
Activate secondary air system
ON/OFF
- Do not perform the test for 5 seconds or more.
- After the test, do not perform the test again for 30 seconds.
Activate the VSV for Evap Control
Activate EVAP VSV control
ON/OFF
-
Control the A/C Cut Signal
Control A/C cut signal
ON/OFF
-
Control the Fuel Pump / Speed
Activate fuel pump (C/OPN relay)
ON/OFF
-
Connect the TC and TE1
Turn on and off TC and TE1 connection
ON/OFF
- ON: TC and TE1 are connected.
- OFF: TC and TE1 are disconnected.
Control the Idle Fuel Cut Prohibit
Prohibit idling fuel cut control
ON/OFF
-
Control the ETCS Open/Close Slow Speed
Throttle actuator
Close/Open
Open: Throttle valve opens slowly
This test is possible when the following conditions are met: - The ignition switch is ON.
- The engine is stopped.
- The accelerator pedal is fully depressed (accelerator pedal sensor: 58 degrees or more).
- The shift lever is in P.
Control the ETCS Open/Close Fast Speed
Throttle actuator
Close/Open
Open: Throttle valve opens quickly
Same as above.
Control the VVT Linear (Bank 1)
Control Variable Valve Timing (VVT)
-128 to 127%
OCV control duty ratio can be set to any value within this range
100%: Maximum advance
-100%: Maximum retard
- The engine stalls or idles roughly when the VVT actuator is operated by 100%.
- The test is possible during idle.
- DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the VVT System (Bank 1)
Turn Oil Control Valve (OCV) on and off
ON/OFF
- The engine stalls or idles roughly when the OCV is turned on.
- The engine runs and idles normally when the OCV is off.
- DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
Control the Cylinder #1 Fuel Cut
Cylinder #1 injector fuel cut
ON/OFF
The test is possible while the vehicle is stopped and the engine is idling.
Control the Cylinder #2 Fuel Cut
Cylinder #2 injector fuel cut
ON/OFF
The test is possible while the vehicle is stopped and the engine is idling.
Control the Cylinder #3 Fuel Cut
Cylinder #3 injector fuel cut
ON/OFF
The test is possible while the vehicle is stopped and the engine is idling.
Control the Cylinder #4 Fuel Cut
Cylinder #4 injector fuel cut
ON/OFF
The test is possible while the vehicle is stopped and the engine is idling.
Check the Cylinder Compression*
Check the cylinder compression pressure
ON/OFF
The fuel injection and ignition stops in all cylinders.
- HINT:
- *: When cranking the engine, each cylinder measures the engine speed.
- In this Active Test, the fuel and ignition of all cylinders is cut and cranking occurs for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.
- Warm up the engine.
- Turn the ignition switch off.
- Connect the intelligent tester to the DLC3.
- Turn the ignition switch to ON.
- Turn the tester on.
- Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.
- HINT:
- To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.
- Push the Function button and then select Snapshot Configuration to set the Trigger Point to zero.
- Set the Record Time to 30 seconds.
- To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.
- Push the snapshot button to turn the snapshot function on.
- HINT:
- Using the snapshot function, data can be recorded during the Active Test.
- While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.
- HINT:
- After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.
- Fully open the throttle.
- Crank the engine for about 10 seconds.
- HINT:
- Continue to crank the engine until the values change from the default value (51199 rpm).
- Monitor the engine speed (Engine Speed of Cyl #1 to #4) displayed on the tester.
- NOTICE:
- Do not crank the engine continuously for 20 seconds or more.
- If Check the Cylinder Compression needs to be performed after it is turned ON and performed once, press the Exit button to return to the Active Test menu screen. Then perform Check the Cylinder Compression again.
- Use a fully-charged battery.
- Do not crank the engine continuously for 20 seconds or more.
- HINT:
- At first, the tester displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.
- Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.
- NOTICE:
- If the Active Test is changed to OFF while the engine is being cranked, the engine will start.
- Push the snapshot button to turn the snapshot function off.
- Enter the following menus: Function / Snapshot Review / Engine and ECT / Snapshot File Manager, select the recorded data and display the data.
- HINT:
- If the data is not displayed, the change in the values cannot be observed.
- Check the change in engine speed values.
- HINT:
- As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.
- Warm up the engine.
- All the injectors are tested at the same time.
| SYSTEM CHECK |
- HINT:
- Performing a system check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs (Pending Codes) are stored, and can detect potential malfunctions in the system. The system check can be performed with the intelligent tester.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Utility.
Perform the system check by referring to the table below.
Turn the ignition switch off.
Tester Display
Test Part
Control Range
Diagnostic Notes
Secondary Air Injection Check
(Automatic Mode)
Perform secondary air injection system operation automatically
-
- With a warm engine, make sure to turn the ignition switch off once.
- If there are no pending DTCs after performing this test, the system is functioning normally.
- Refer to the inspection procedure for secondary air injection system DTCs.
- When performing the Secondary Air Injection Check operation after the battery cable is reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
- Turn the ignition switch off when the system check is finished.
Secondary Air Injection Check
(Manual Mode)
Perform secondary air injection system operation manually Select monitor item 1, 2 or 3 - Air pump: ON
Air switching valve: OPEN
- Air pump: OFF
Air switching valve: CLOSE
- Air pump: ON
Air switching valve: CLOSE
-
- With a warm engine, make sure to turn the ignition switch off once.
- Used to detect malfunctioning parts.
- Refer to the inspection procedure for secondary air injection system DTCs.
- When performing the Secondary Air Injection Check operation after the battery cable is reconnected, wait for 7 minutes with the ignition switch ON or the engine running.
- Turn the ignition switch off when the system check is finished.
- With a warm engine, make sure to turn the ignition switch off once.