2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

TERMINALS OF ECM

System information · Vehicles built from Aug 2013

A139495E02

HINT:
Each ECM terminal's standard voltage is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to be inspected. The standard voltage between the terminals is shown under "Specified Condition". Use the illustration above as a reference for the ECM terminals.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G61-1 (BATT) - C101-14 (E1)
L - BR
Battery (for measuring the battery voltage and for ECM memory)
Always
11 to 14 V
G61-2 (SREL) - C101-13 (E01)
R - W-B
GLOW relay
Cranking
11 to 14 V
G61-2 (SREL) - C101-13 (E01)
R - W-B
GLOW relay
Idling
(engine started and 600 sec. have passed)
0 to 1.5 V
G61-3 (MREL) - C101-14 (E1)
V - BR
MAIN relay
Ignition switch ON
11 to 14 V
G61-3 (MREL) - C101-14 (E1)
V - BR
MAIN relay
Ignition switch off
(2 sec. after ignition switch off)
0 to 1.5 V
G61-4 (TC) - C101-14 (E1)
V - BR
Terminal TC of DLC3
Ignition switch ON
11 to 14 V
G61-5 (W) - C101-14 (E1)
V - BR
MIL
MIL illuminated
0 to 3 V
G61-5 (W) - C101-14 (E1)
V - BR
MIL
MIL not illuminated
11 to 14 V
G61-8 (THWO) - C101-14 (E1)
L - BR
Combination meter assembly
Ignition switch ON
Pulse generation
(See waveform 1)
G61-9 (SPD) - C101-14 (E1)
R - BR
Speed signal from combination meter assembly
Ignition switch ON, driving wheel rotating slowly
Pulse generation
(See waveform 2)
G61-11 (STA) - C101-14 (E1)
W - BR
Starter signal
Cranking
6 V or more
G61-12 (+B) - C101-14 (E1)
W - BR
Power source of ECM
Ignition switch ON
11 to 14 V
G61-14 (IGSW) - C101-14 (E1)
W - BR
Ignition switch
Ignition switch ON
11 to 14 V
G61-15 (SIL) - C101-14 (E1)
W - BR
Terminal SIL of DLC3
Intelligent tester connected to DLC3
Pulse generation
G61-19 (STP) - C101-14 (E1)
V - BR
Stop light switch
Brake pedal depressed
11 to 14 V
G61-19 (STP) - C101-14 (E1)
V - BR
Stop light switch
Brake pedal released
Below 1.5 V
G62-1 (GIND) - C101-14 (E1)
R - BR
Glow indicator light
Glow indicator light lights up
0 to 3 V
G62-1 (GIND) - C101-14 (E1)
R - BR
Glow indicator light
Glow indicator light does not light up
11 to 14 V
G62-2 (AC1) - C101-14 (E1)
LG - BR
A/C amplifier
A/C switch on
(magnetic clutch on)
Below 1.5 V
G62-2 (AC1) - C101-14 (E1)
LG - BR
A/C amplifier
A/C switch off
7.5 to 14 V
G62-8 (ACT) - C101-14 (E1)
R - BR
A/C amplifier
Ignition switch ON
11 to 14 V
G62-8 (ACT) - C101-14 (E1)
R - BR
A/C amplifier
A/C cut performed (driving below 30 km/h (18.6 mph), accelerator pedal fully depressed for 5 sec.)
0 to 3 V
G62-5 (VPA) - G62-4 (EPA)
L - P
Accelerator pedal position sensor (for engine control)
Ignition switch ON, accelerator pedal released
0.5 to 1.1 V
G62-5 (VPA) - G62-4 (EPA)
L - P
Accelerator pedal position sensor (for engine control)
Ignition switch ON, accelerator pedal depressed
2.6 to 4.5 V
G62-12 (VPA2) - G62-4 (EPA)
GR - P
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal released
1.2 to 2.0 V
G62-12 (VPA2) - G62-4 (EPA)
GR - P
Accelerator pedal position sensor (for sensor malfunction detection)
Ignition switch ON, accelerator pedal depressed
3.4 to 5.3 V
G62-6 (VCPA) - G62-4 (EPA)
LG - P
Power source of accelerator pedal position sensor (for VPA)
Ignition switch ON
4.5 to 5.5 V
G62-7 (TACH) - C101-14 (E1)
P - BR
Engine speed sensor
Idling
Pulse generation
(See waveform 3)
G62-11 (ST1-) - C101-14 (E1)
B - BR
Stop light switch
Brake pedal depressed
Below 1.5 V
G62-11 (ST1-) - C101-14 (E1)
B - BR
Stop light switch
Brake pedal released
11 to 14 V
C102-1 (VC) - C102-9 (E2)
R-W - BR
Power source of sensor (specific voltage)
Ignition switch ON
4.75 to 5.25 V
C102-2 (PIM) - C102-9 (E2)
L-B - BR
Manifold absolute pressure sensor
60 kPa (450 mmHg, 17.7 in.Hg) vacuum applied
0.2 to 0.8 V
C102-2 (PIM) - C102-9 (E2)
L-B - BR
Manifold absolute pressure sensor
207 kPa (1550 mmHg, 61.0 in.Hg) vacuum applied
4.2 to 4.8 V
C102-3 (THA) - C102-9 (E2)
B - BR
Intake air temperature sensor
Idling, air intake temp. 0°C (32°F) to 80°C (176°F)
0.5 to 3.4 V
C102-4 (THW) - C102-9 (E2)
R-L - BR
Engine coolant temperature sensor
Idling, engine coolant temp. 60°C (140°F) to 120°C (248°F)
0.2 to 1.0 V
C102-5 (THF) - C102-9 (E2)
G-B - BR
Fuel temperature sensor
Ignition switch ON (engine cold)
0.5 to 3.4 V
C102-6 (DATA) - C101-14 (E1)
Y - BR
Injection pump
Within 0.5 sec. after ignition switch ON
Pulse generation
C102-14 (CLK) - C101-14 (E1)
L - BR
Injection pump
Within 0.5 sec. after ignition switch ON
Pulse generation
C102-15 (THOC) - C101-14 (E1)
GR - BR
Throttle open switch
Idling (engine warmed up)
11 to 14 V
C102-15 (THOC) - C101-14 (E1)
GR - BR
Throttle open switch
Ignition switch ON (once within 5 sec.)
0 to 3 V
C101-7 (LU-B) - C101-13 (E01)
L-Y - W-B
Throttle control motor
(intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 4)
C101-8 (LU+B) - C101-13 (E01)
L-R - W-B
Throttle control motor
(intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 4)
C101-9 (LU-A) - C101-13 (E01)
L-W - W-B
Throttle control motor
(intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 4)
C101-10 (LU+A) - C101-13 (E01)
L-B - W-B
Throttle control motor
(intake shutter)
Racing (engine warmed up)
Pulse generation
(See waveform 4)
C101-11 (TCV) - C101-13 (E01)
R-W - W-B
Timing control valve
Ignition switch ON
11 to 14 V
C101-11 (TCV) - C101-13 (E01)
R-W - W-B
Timing control valve
Idling
Pulse generation
(See waveform 5)
C101-12 (SPV+) - C101-14 (E1)
R-L - BR
Spill control valve
Ignition switch ON
11 to 14 V
C101-12 (SPV+) - C101-14 (E1)
R-L - BR
Spill control valve
Idling
Pulse generation
C101-25 (SPV-) - C101-14 (E1)
R-Y - BR
Spill control valve
Idling
Pulse generation
(See waveform 7)
C101-17 (TDC+) - C101-16 (TDC-)
G - R
Crankshaft position sensor
Idling
Pulse generation
(See waveform 6)
C101-19 (NE+) - C101-18 (NE-)
W - B
Engine speed sensor
Idling
Pulse generation
(See waveform 6)


Waveform 1

  1. A105099E07
    A/C amplifier signal
    Terminal No. (Symbol)
    G61-8 (THWO) - C101-14 (E1)
    Tester Range
    5 V/DIV., 0.1 sec./DIV.
    Condition
    Idling

    HINT:
    Waveform time A changes according to coolant temperature.


Waveform 2

  1. A110545E05
    Speed signal
    Terminal No. (Symbol)
    G61-9 (SPD) - C101-14 (E1)
    Tester Range
    2 V/DIV., 20 msec./DIV.
    Condition
    Driving at approx. 20 km/h (12.4 mph)

    HINT:
    1. As vehicle speed increases, the wavelength becomes shorter.
    2. As vehicle speed increases, the waveform's amplitude becomes greater.


Waveform 3

  1. A110546E08
    Engine speed signal
    Terminal No. (Symbol)
    G62-7 (TACH) - C101-14 (E1)
    Tester Range
    5 V/DIV., 20 msec./DIV.
    Condition
    Idling after warming up

    HINT:
    As engine speed increases, the wavelength becomes shorter.


Waveform 4

  1. A110547E03
    Throttle control motor signals
    Terminal No. (Symbol)
    C101-10 (LU+A) - C101-13 (E01)
    C101-8 (LU+B) - C101-13 (E01)
    C101-9 (LU-A) - C101-13 (E01)
    C101-7 (LU-B) - C101-13 (E01)
    Tester Range
    10 V/DIV., 0.5 msec./DIV.
    Condition
    Engine racing


Waveform 5

  1. A002482E06
    Timing control value signal
    Terminal No. (Symbol)
    C101-11 (TCV) - C101-13 (E01)
    Tester Range
    10 V/DIV., 10 msec./DIV.
    Condition
    During idling


Waveform 6

  1. A002483E03
    Crankshaft position sensor and engine speed sensor signals
    Terminal No. (Symbol)
    C101-17 (TDC+) - C101-16 (TDC-)
    C101-19 (NE+) - C101-18 (NE-)
    Tester Range
    2 V/DIV., 20 msec./DIV.
    Condition
    During idling


Waveform 7

  1. A110550E04
    Spill control valve signal
    Terminal No. (Symbol)
    C101-25 (SPV-) - C101-14 (E1)
    Tester Range
    20 V/DIV., 10 msec./DIV.
    Condition
    During idling

← PROBLEM SYMPTOMS TABLE (from Aug 2014)DIAGNOSIS SYSTEM (Aug 2013 – Jul 2014) →