2013-2015 Land Cruiser Prado · Service Manual Engine / Hybrid System

Pre-heating Control Circuit

Circuit diagnosis · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

The glow plug is mounted inside the engine combustion chamber. To ensure efficient engine starting with a cold engine, the ECM calculates the period of time that the current needs to flow through the glow plug depending on the starting engine coolant temperature when the ignition switch is turned to ON. The ECM then turns on the glow plug relay and permits the current to flow through the glow plug based on the time calculated by the ECM. The glow plug is then heated, and enhances fuel combustion with a cold engine.
A129368E15

HINT:
  1. These troubleshooting procedures are for: 1) difficulty starting the engine in cold weather, and 2) difficulty driving/vehicle malfunctions in cold weather immediately after the engine is started.
  2. After the engine is started, the ECM performs "after-glow" for a certain period of time. In proportion to the actual engine coolant temperature, the time period varies. The after-glow reduces diesel engine knocking, white smoke emissions and engine noises when the engine is cold.

A117830E12

WIRING DIAGRAM

A227729E02

INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses of circuits related to this system before performing the following inspection procedure.
  2. After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).


1. CHECK TERMINAL VOLTAGE (GLOW PLUG RELAY(GLOW))

  1. A227730E01
    Remove the glow plug relay (GLOW).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Glow plug relay terminal-5 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block
    *2
    Glow Plug Relay (GLOW)

  1. Reinstall the glow plug relay (GLOW).



NG
REPAIR OR REPLACE HARNESS AND CONNECTOR (GLOW PLUG RELAY - BATTERY)
OK


2. INSPECT GLOW PLUG RELAY(GLOW)
  1. Inspect the glow plug relay (GLOW) (Click here).



NG
REPLACE GLOW PLUG RELAY
OK


3. INSPECT GLOW PLUG (RESISTANCE)
  1. Inspect the glow plug (Click here).



NG
REPLACE GLOW PLUG ASSEMBLY (Click here)
OK


4. CHECK GLOW PLUG (INSTALLATION)
  1. Check the glow plug installation.

    OK:
    Glow plugs are installed securely.

Torque:
12.3 N*m{ 125 kgf*cm , 9 ft.*lbf }



NG
TIGHTEN GLOW PLUG
OK


5. CHECK WIRE HARNESS (GLOW PLUG - GLOW PLUG RELAY(GLOW) - BODY GROUND)
  1. Remove the glow plug relay (GLOW).

  1. Disconnect the glow plug connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Glow plug relay terminal-3 - C98-1
    Always
    Below 1 Ω
    Glow plug relay terminal-1 - Body ground
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Glow plug relay terminal-3 or C98-1 - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the glow plug relay (GLOW).

  1. Reconnect the glow plug connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK WIRE HARNESS (GLOW PLUG RELAY(GLOW) - ECM AND BODY GROUND)
  1. Remove the glow plug relay (GLOW).

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    Glow plug relay terminal-2 - C91-19 (GREL)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    Glow plug relay terminal-2 or C91-19 (GREL) - Body ground
    Always
    10 kΩ or higher

  1. Reinstall the glow plug relay (GLOW).

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← Pre-heating Control Circuit (Aug 2013 – Jul 2014)Rough Idling or Excessive Engine Vibrations (Aug 2013 – Jul 2014) →