TERMINALS OF ECM
System information · Vehicles built from Aug 2013
| CHECK ECM |


- HINT:
- The standard voltage at each ECM terminal is shown in the table below.
- In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".
- Use the illustration above as a reference for the ECM terminals.
| Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| G55-16 (L4) - C36-12 (E1) |
R - BR |
L4 position signal |
|
Below 1 V |
|
11 to 14 V |
|||
| C35-2 (NSW) - C36-12 (E1) |
B - BR |
PNP switch signal |
|
Below 1 V |
|
11 to 14 V |
|||
| C34-35 (P) - C36-12 (E1) |
L - BR |
P shift position switch signal |
|
11 to 14 V |
|
Below 1 V |
|||
| C34-28 (R) - C36-12 (E1) |
R - BR |
R shift position switch signal |
|
11 to 14 V |
|
Below 1 V |
|||
| C34-29 (N) - C36-12 (E1) |
G - BR |
N shift position switch signal |
|
11 to 14 V |
|
Below 1 V |
|||
| C34-27 (D) - C36-12 (E1) |
B - BR |
D shift position switch signal |
|
11 to 14 V |
|
Below 1 V |
|||
| G56-24 (S) - C36-12 (E1) |
V - BR |
S shift position switch signal |
|
11 to 14 V |
|
Below 1 V |
|||
| G56-16 (SFTU) - C36-12 (E1) |
GR - BR |
Up-shift position switch signal |
|
11 to 14 V |
|
Below 1 V |
|||
| G56-22 (SFTD) - C36-12 (E1) |
LG - BR |
Down-shift position switch signal |
|
11 to 14 V |
|
Below 1 V |
|||
| C35-36 (S1) - C36-12 (E1) |
L - BR |
S1 solenoid signal |
Ignition switch ON |
11 to 14 V |
| 1st or 2nd gear |
11 to 14 V |
|||
| 3rd, 4th or 5th gear |
Below 1 V |
|||
| C34-33 (S2) - C36-12 (E1) |
L-W - BR |
S2 solenoid signal |
Ignition switch ON |
Below 1 V |
| 2nd or 3rd gear |
11 to 14 V |
|||
| 1st, 4th or 5th gear |
Below 1 V |
|||
| C34-31 (SR) - C36-12 (E1) |
R - BR |
SR solenoid signal |
Ignition switch ON |
Below 1 V |
| 5th gear |
11 to 14 V |
|||
| 1st gear |
Below 1 V |
|||
| C36-33 (SL1+) - C36-32 (SL1-) |
V - R-B |
SL1 solenoid signal |
Engine idling |
Pulse generation |
| C35-31 (SL2+) - C36-34 (SL2-) |
LG - P-L |
SL2 solenoid signal |
Engine idling |
Pulse generation |
| C35-34 (SLT+) - C35-35 (SLT-) |
G-Y - L-B |
SLT solenoid signal |
Engine idling |
Pulse generation |
| C35-33 (SLU+) - C35-32 (SLU-) |
P - LG |
SLU solenoid signal |
4th gear (lock-up) or 5th gear (lock-up) |
Pulse generation |
| C36-5 (THO1) - C35-8 (ETHW) |
V - W-R |
No. 1 ATF temperature sensor signal |
No. 1 ATF temperature 115°C (239°F) or higher |
Below 1.5 V |
| C36-11 (THO2) - C35-8 (ETHW) |
L - W-R |
No. 2 ATF temperature sensor signal |
No. 2 ATF temperature 115°C (239°F) or higher |
Below 1.5 V |
| C36-9 (SP2+) - C36-10 (SP2-) |
B - W |
Speed sensor SP2 signal |
Vehicle speed 20 km/h (12 mph) |
Pulse generation (See waveform 1) |
| C36-3 (NT+) - C36-4 (NT-) |
L - W |
Speed sensor NT signal |
Engine idling (shift lever in P or N) |
Pulse generation (See waveform 2) |
| G55-21 (SNWI) - C36-12 (E1) |
GR - BR |
Pattern select (2nd) switch signal |
|
Below 1 V |
|
11 to 14 V |
|||
| G56-32 (CANH) - C36-12 (E1) |
R - BR*1 LG - BR*2 |
CAN communication line |
Ignition switch ON |
Pulse generation (See waveform 3) |
| G56-31 (CANL) - C36-12 (E1) |
W - BR |
CAN communication line |
Ignition switch ON |
Pulse generation (See waveform 4) |
- *1: for LHD
- *2: for RHD
Using an oscilloscope, check waveform 1.

Reference Terminal No. (Symbol)
Tool Setting
Condition
C36-9 (SP2+) - C36-10 (SP2-)
2 V/DIV., 20 msec./DIV.
Vehicle speed 20 km/h (12 mph)
Using an oscilloscope, check waveform 2.

Reference Terminal No. (Symbol)
Tool Setting
Condition
C36-3 (NT+) - C36-4 (NT-)
1 V/DIV., 2 msec./DIV.
Engine idling (shift lever in P or N)
Using an oscilloscope, check waveform 3.

Reference Terminal No. (Symbol)
Tool Setting
Condition
G56-32 (CANH) - C36-12 (E1)
1 V/DIV., 10 μsec./DIV.
Ignition switch ON
Using an oscilloscope, check waveform 4.

Reference Terminal No. (Symbol)
Tool Setting
Condition
G56-31 (CANL) - C36-12 (E1)
1 V/DIV., 10 μsec./DIV.
Ignition switch ON