2013-2015 Land Cruiser Prado · Service Manual Drivetrain

TERMINALS OF ECM

System information · Vehicles built from Aug 2013


CHECK ECM
C214980E01

HINT:
The standard voltage at each ECM terminal is shown in the table below.
In the table, first follow the information under "Condition". Look under "Terminal No. (Symbol)" for the terminals to inspect. The standard voltage between the terminals is shown under "Specified Condition".
Use the illustration above as a reference for the ECM terminals.

Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
G60-24 (NSW) - C64-5 (E1)
B - BR
PNP switch signal
  1. Ignition switch ON
  2. Shift lever in P or N
Below 1 V
  1. Ignition switch ON
  2. Shift lever not in P or N
11 to 14 V
C63-16 (P) - C64-5 (E1)
L - BR
P shift position switch signal
  1. Ignition switch ON
  2. Shift lever in P
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in P
Below 1 V
C63-17 (R) - C64-5 (E1)
R - BR
R shift position switch signal
  1. Ignition switch ON
  2. Shift lever in R
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in R
Below 1 V
C63-11 (N) - C64-5 (E1)
G - BR
N shift position switch signal
  1. Ignition switch ON
  2. Shift lever in N
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in N
Below 1 V
G60-9 (D) - C64-5 (E1)
B - BR
D shift position switch signal
  1. Ignition switch ON
  2. Shift lever in D or 3
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in D or 3
Below 1 V
G60-23 (3) - C64-5 (E1)
V - BR
3 shift position switch signal
  1. Ignition switch ON
  2. Shift lever in 3
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 3
Below 1 V
C63-15 (2) - C64-5 (E1)
P - BR
2 shift position switch signal
  1. Ignition switch ON
  2. Shift lever in 2
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in 2
Below 1 V
C63-25 (L) - C64-5 (E1)
W - BR
L shift position switch signal
  1. Ignition switch ON
  2. Shift lever in L
11 to 14 V
  1. Ignition switch ON
  2. Shift lever not in L
Below 1 V
C62-21 (S1) - C64-5 (E1)
B-W - BR
S1 solenoid signal
1st or 2nd gear
11 to 14 V
3rd or 4th gear
Below 1 V
C62-22 (S2) - C64-5 (E1)
B-R - BR
S2 solenoid signal
2nd or 3rd gear
11 to 14 V
1st or 4th gear
Below 1 V
C62-23 (SLT+) - C62-24 (SLT-)
G-B - L-B
SLT solenoid signal
Engine idling
Pulse generation
C63-20 (SLU+) - C63-21 (SLU-)
P - LG
SLU solenoid signal
3rd gear (lock-up) or 4th gear (lock-up)
Pulse generation
C62-18 (THO1) - C62-17 (ETHO)
L - R
No. 1 ATF temperature sensor signal
No. 1 ATF temperature: 115°C (239°F) or higher
Below 1.5 V
C61-2 (THOC) - C62-16 (E2)
W-L - W-R
No. 2 ATF temperature sensor signal
No. 2 ATF temperature: 115°C (239°F) or higher
Below 1.5 V
C63-2 (SP2+) - C63-9 (SP2-)
B - W
Speed sensor SP2 signal
Vehicle speed 20 km/h (12 mph)
Pulse generation
(See waveform 1)
C63-5 (NCO+) - C63-10 (NCO-)
L - W
Speed sensor NCO signal
Engine idling
(shift lever in P or N)
Pulse generation
(See waveform 2)
G59-14 (L4) - C64-5 (E1)
R - BR
L4 position signal
  1. Ignition switch ON
  2. Transfer in L4
Below 1 V
  1. Ignition switch ON
  2. Transfer not in L4
11 to 14 V
G60-34 (CANH) - C64-5 (E1)
LG - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 3)
G60-33 (CANL) - C64-5 (E1)
W - BR
CAN communication line
Ignition switch ON
Pulse generation
(See waveform 4)
G60-27 (SNWI) - C64-5 (E1)
GR - BR
Pattern select (2ND) switch signal
  1. Ignition switch ON
  2. Pattern select (2ND) switch pushed
Below 1 V
  1. Ignition switch ON
  2. Pattern select (2ND) switch not pushed
11 to 14 V

  1. C161208E04
    Using an oscilloscope, check waveform 1.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C63-2 (SP2+) - C63-9 (SP2-)
    2 V/DIV., 20 msec./DIV.
    Vehicle speed 20 km/h (12 mph)

  2. C162170E03
    Using an oscilloscope, check waveform 2.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    C63-5 (NCO+) - C63-10 (NCO-)
    1 V/DIV., 2 msec./DIV.
    Engine idling (shift lever in P or N)

  3. C161206E03
    Using an oscilloscope, check waveform 3.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    G60-34 (CANH) - C64-5 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON

  4. C161207E03
    Using an oscilloscope, check waveform 4.
    Reference 
    Terminal No. (Symbol)
    Tool Setting
    Condition
    G60-33 (CANL) - C64-5 (E1)
    1 V/DIV., 10 μsec./DIV.
    Ignition switch ON

← PROBLEM SYMPTOMS TABLE (from Aug 2014)DIAGNOSIS SYSTEM (Aug 2013 – Jul 2014) →