2013-2015 Land Cruiser Prado · Service Manual Drivetrain

P0717 Turbine Speed Sensor Circuit No Signal

Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

This sensor detects the rotation speed of the turbine which indicates the input speed of the transmission. By comparing the input turbine speed signal NCO with the output speed sensor signal SP2, the ECM detects the shift timing of the gears and appropriately controls the engine torque and hydraulic pressure according to various conditions, and as a result, the gears shift smoothly.
DTC Code
DTC Detection Condition
Trouble Area
P0717
All conditions are met for 5 seconds or more (1-trip detection logic):
(a) Transmission input shaft speed is 300 rpm or less.
(b) Transmission output shaft speed is 500 rpm or more.
(c) Park/neutral position switch R input signal is OFF.
  1. Open or short in speed sensor NCO circuit
  2. Speed sensor NCO
  3. ECM
  4. Automatic transmission (clutch, brake, gear, etc.)
Reference: Inspect using an oscilloscope.
Check the waveform of the ECM connector.

Standard:
Terminal No. (Symbol)
Tool Setting
Condition
Specified Condition
C63-5 (NCO+) - C63-10 (NCO-)
1 V/DIV., 2 msec./DIV.
Engine idling (Shift lever in P or N)
Refer to illustration

C162170E04

MONITOR DESCRIPTION

This DTC indicates that a pulse is not output from the speed sensor NCO (turbine (input) speed sensor) or is output only a little. The NCO terminal of the ECM detects the pulse signal from the speed sensor NCO (input turbine speed). The ECM outputs a gear shift signal by comparing the input speed sensor NCO signal with the output speed sensor SP2 signal.
If the input shaft speed is less than 300 rpm*1 although the output shaft speed is 500 rpm or more*2, the ECM detects the trouble, illuminates the MIL and stores the DTC.

HINT:
  1. *1: A pulse is not output or is irregularly output.
  2. *2: The vehicle speed is approximately 50 km/h (30 mph) or more.


WIRING DIAGRAM

C214967E01

INSPECTION PROCEDURE


DATA LIST

HINT:
Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the intelligent tester to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the intelligent tester on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the tester, read the Data List.

    Engine and ECT 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    SPD (NC0)
    Input shaft speed/
    Min.: 0 rpm
    Max.: 12750 rpm
    1. Lock-up ON (after warming up engine): Input turbine speed (NCO) equal to engine speed
    2. Lock-up OFF (idling with shift lever in N): Input turbine speed (NCO) nearly equal to engine speed
    Data is displayed in increments of 50 rpm.

    HINT:
    1. SPD (NC0) is always 0 while driving:
      Open or short in the sensor or circuit.
    2. SPD (NC0) is always more than 0 and less than 300 rpm while driving the vehicle at 50 km/h (30 mph) or more:
      Sensor trouble, improper installation, or intermittent connection trouble in the circuit.


1. INSPECT SPEED SENSOR NCO INSTALLATION

  1. C211922E01
    Check the speed sensor NCO installation.

    OK:
    The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.

    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT



NG
SECURELY INSTALL OR REPLACE SPEED SENSOR NCO (Click here)
OK


2. INSPECT SPEED SENSOR NCO

  1. C206284E03
    Disconnect the C59 speed sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    560 to 680 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Speed Sensor NCO)



NG
REPLACE SPEED SENSOR NCO (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (SPEED SENSOR NCO - ECM)

  1. C214337E06
    Disconnect the C63 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C63-5 (NCO+) - C63-10 (NCO-)
    20°C (68°F)
    560 to 680 Ω
    C63-5 (NCO+) - Body ground
    Always
    10 kΩ or higher
    C63-10 (NCO-) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*a
Rear view of wire harness connector
(to ECM)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0712 Transmission Fluid Temperature Sensor "A" Circuit Low Input (+ P0713) (from Aug 2014)P0717 Turbine Speed Sensor Circuit No Signal (from Aug 2014) →