P2714 Pressure Control Solenoid "D" Performance (Shift Solenoid Valve SLT)
Diagnostic trouble codes · Vehicles built from Aug 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION


Shift solenoid valve SLT controls the transmission line pressure for smooth transmission operation based on signals from the throttle position sensor and vehicle speed sensor. The TCM adjusts the current to shift solenoid valve SLT to control the hydraulic line pressure coming from the primary regulator valve. Appropriate line pressure assures smooth shifting with varying engine outputs.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| P2714 |
The TCM detects a malfunction in shift solenoid valve SLT (ON side) according to the difference in speed of the turbine and output shaft, and also by the oil pressure (2-trip detection logic*1, 1-trip detection logic*2). |
|
*2: w/o OBD
MONITOR DESCRIPTION
The TCM calculates the amount of heat absorbed by the friction material based on the difference in speed (clutch slippage) between the turbine and output shaft. The TCM turns on the MIL and outputs this DTC when the amount of heat absorption exceeds the specified value.There are two reasons that the speed may be different.
- When shift solenoid valve SLT remains on, oil pressure goes down and clutch engagement force decreases.
- When the shift solenoid valve remains on or off, the gear position commanded by the TCM and the actual gear position are not the same.
- NOTICE:
- If the vehicle continues to be driven under these conditions, the clutch will burn out and the vehicle will no longer be drivable.
INSPECTION PROCEDURE
| 1. CHECK DTC OUTPUT (IN ADDITION TO DTC P2714) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / DTC.
Read the DTCs using the tester.
Result Result
Proceed to
Only P2714 is output
A
P2714 and other DTCs are output
B
- HINT:
- If any other codes besides P2714 are output, perform troubleshooting for those DTCs first.
|
|
||||
| A | |
| 2. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (SHIFT SOLENOID VALVE SLT) |
- NOTICE:
- Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).
- Be careful to prevent the hose of SST from interfering with the exhaust pipe.
- Perform the test with the A/C off.
- Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Remove the test plug from the transmission case and connect SST.

- SST
- 09992-00095
(09992-00231, 09992-00271)
Connect the intelligent tester to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the intelligent tester on.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the tester, perform the Active Test.
Measure the line pressure.
ECT Tester Display
Test Part
Control Range
Diagnostic Note
Activate the Solenoid (SLT)*
Operate shift solenoid valve SLT and raise line pressure
ON or OFF - HINT:
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
- ON: No action (normal operation)
- OFF: Line pressure up (when Active Test "Activate the Solenoid (SLT)" is performed, TCM commands shift solenoid valve SLT to turn OFF)
[Vehicle Condition] - Vehicle stopped
- Engine idling
- HINT:
- *: Activate the Solenoid (SLT) in the Active Test is performed to check the line pressure changes by connecting SST to the automatic transmission, which is used in the Hydraulic Test (Click here) as well. Note that the pressure values in the Active Test and hydraulic test are different.
- OK:
- The line pressure changes as specified when performing the Active Test.
|
|
||||
| OK | |
| 3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (RUNNING TEST) |
- CAUTION:
- This test should always be performed with at least 2 people.
- NOTICE:
- Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).
- Perform the test with the A/C turned off.
- Perform the test while the ATF temperature is between 50 and 80°C (122 and 176°F).
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Clear the DTC (Click here).
Warm up the engine.
Enter the following menus: Powertrain / ECT / Active Test.
According to the display on the tester, perform the Active Test.
- HINT:
- While driving, the shift position can be forcibly changed with the intelligent tester.
ECT Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
Operate shift solenoid valves and set each shift position
- Press "→" button: Shift up
- Press "←" button: Shift down
Possible to check operation of the shift solenoid valves.
[Vehicle Condition]
50 km/h (31 mph) or less
- HINT:
- This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
- The 4th to 5th up-shift must be performed with the accelerator pedal released.
- The 5th to 4th down-shift must be performed with the accelerator pedal released.
- Do not operate the accelerator pedal for at least 2 seconds after shifting and do not shift successively.
- The shift position commanded by the TCM is shown in the Data List display on the tester.
- This test can be conducted when the vehicle speed is 50 km/h (31 mph) or less.
Compare the TCM gear shift command and actual gear position.
- OK:
- Gear position changes in accordance with the tester command.
Result System Condition
TCM Gear Shift Command
Proceed to
1st
2nd
3rd
4th
5th
Malfunction
Shift solenoid S1
Stuck ON
1st
2nd
2nd
1st
N*1
A
Stuck OFF
4th
3rd
3rd
4th
5th
Shift solenoid S2
Stuck ON*2
2nd
2nd
3rd
3rd
N*1
B
Stuck OFF*3
1st
1st
4th
4th
5th
Shift solenoid SL2
Stuck ON
1st
2nd
3rd
4th
N*1
C
Stuck OFF
1st
2nd
3rd
4th
5th
Shift solenoid SR
Stuck ON*4
1st
2nd
3rd
4th
5th
D
Stuck OFF*5
1st
2nd
3rd
4th
4th
Normal
1st
2nd
3rd
4th
5th
E
- HINT:
- *1: Neutral
- *2: When shift solenoid valve S2 is stuck ON, the vehicle cannot drive in reverse.
- *3: When shift solenoid valve S2 is stuck OFF, the 4th to 5th up-shift will have a large shift shock. Also, the 5th to 4th down-shift will have time lag.
- *4: Stuck ON condition can be determined by checking if shift shock has increased excessively.
- *5: When shift solenoid valve SR is stuck OFF, moving the shift lever from N to D will cause a large shift shock.
- Gear shifts can be determined by paying attention to changes in rpm.
- *1: Neutral
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | |
| 4. INSPECT SHIFT SOLENOID VALVE S1 |
Remove shift solenoid valve S1.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body
20°C (68°F)
11 to 15 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) → Shift solenoid valve S1 connector
- Battery negative (-) → Shift solenoid valve S1 body
Valve moves and makes an operating noise
- Battery positive (+) → Shift solenoid valve S1 connector
| *a |
Component without harness connected (Shift Solenoid Valve S1) |
|
|
||||
| OK | |
| 5. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on any valve.
|
|
||||
| OK | |
| 6. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Check the torque converter clutch assembly (Click here).
- OK:
- The torque converter clutch operates normally.
|
|
||||
| OK | ||
| ||
| 7. INSPECT SHIFT SOLENOID VALVE SLT |
Remove shift solenoid valve SLT.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) with a 21 W bulb → Terminal 2
- Battery negative (-) → Terminal 1
Valve moves and makes an operating noise
- Battery positive (+) with a 21 W bulb → Terminal 2
| *a |
Component without harness connected (Shift Solenoid Valve SLT) |
|
|
||||
| OK | |
| 8. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on any valve.
|
|
||||
| OK | |
| 9. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Check the torque converter clutch assembly (Click here).
- OK:
- The torque converter clutch operates normally.
|
|
||||
| OK | ||
| ||
| 10. INSPECT SHIFT SOLENOID VALVE S2 |
Remove shift solenoid valve S2.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Shift solenoid valve S2 connector terminal - Shift solenoid valve S2 body
20°C (68°F)
11 to 15 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) → Shift solenoid valve S2 connector
- Battery negative (-) → Shift solenoid valve S2 body
Valve moves and makes an operating noise
- Battery positive (+) → Shift solenoid valve S2 connector
| *a |
Component without harness connected (Shift Solenoid Valve S2) |
|
|
||||
| OK | |
| 11. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on any valve.
|
|
||||
| OK | |
| 12. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Check the torque converter clutch assembly (Click here).
- OK:
- The torque converter clutch operates normally.
|
|
||||
| OK | ||
| ||
| 13. INSPECT SHIFT SOLENOID VALVE SL2 |
![]() ![]() |
Remove shift solenoid valve SL2.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) with a 21 W bulb → Terminal 1
- Battery negative (-) → Terminal 2
Valve moves and makes an operating noise
- Battery positive (+) with a 21 W bulb → Terminal 1
| *a |
Component without harness connected (Shift Solenoid Valve SL2) |
|
|
||||
| OK | |
| 14. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on any valve.
|
|
||||
| OK | |
| 15. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Check the torque converter clutch assembly (Click here).
- OK:
- The torque converter clutch operates normally.
|
|
||||
| OK | ||
| ||
| 16. INSPECT SHIFT SOLENOID VALVE SR |
Remove shift solenoid valve SR.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
Shift solenoid valve SR connector terminal - Shift solenoid valve SR body
20°C (68°F)
11 to 15 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) → Shift solenoid valve SR connector
- Battery negative (-) → Shift solenoid valve SR body
Valve moves and makes an operating noise
- Battery positive (+) → Shift solenoid valve SR connector
| *a |
Component without harness connected (Shift Solenoid Valve SR) |
|
|
||||
| OK | |
| 17. INSPECT SHIFT SOLENOID VALVE SL1 |
Remove shift solenoid valve SL1.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) with a 21 W bulb → Terminal 1
- Battery negative (-) → Terminal 2
Valve moves and makes an operating noise
- Battery positive (+) with a 21 W bulb → Terminal 1
| *a |
Component without harness connected (Shift Solenoid Valve SL1) |
|
|
||||
| OK | |
| 18. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on any valve.
|
|
||||
| OK | |
| 19. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Check the torque converter clutch assembly (Click here).
- OK:
- The torque converter clutch operates normally.
|
|
||||
| OK | ||
| ||
| 20. INSPECT SHIFT SOLENOID VALVE SLT |
Remove shift solenoid valve SLT.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) with a 21 W bulb → Terminal 2
- Battery negative (-) → Terminal 1
Valve moves and makes an operating noise
- Battery positive (+) with a 21 W bulb → Terminal 2
| *a |
Component without harness connected (Shift Solenoid Valve SLT) |
|
|
||||
| OK | |
| 21. INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly (Click here).
- OK:
- There are no foreign objects on any valve.
|
|
||||
| OK | |
| 22. INSPECT TORQUE CONVERTER CLUTCH ASSEMBLY |
Check the torque converter clutch assembly (Click here).
- OK:
- The torque converter clutch operates normally.
|
|
||||
| OK | ||
| ||
