P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input)
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
The Park/Neutral Position (PNP) switch detects the shift lever position and sends signals to the ECM.| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0705 |
One of the following conditions is met: (A) Any 2 or more of the following signals are ON simultaneously (2-trip detection logic):
(C) Any of the following signals is ON for 2.0 seconds or more with the shift lever in 3 (2-trip detection logic):
|
|
MONITOR DESCRIPTION
This DTC indicates a problem with the park/neutral position switch or the wire harness in the park/neutral position switch circuit.The park/neutral position switch detects the shift lever position and sends a signal to the ECM.
For security, the park/neutral position switch detects the shift lever position so that the engine can be started only when the shift lever is in P or N.
The park/neutral position switch sends a signal to the ECM according to the shift lever position (P, R, N, D, 3, 2 or L).
The ECM determines that there is a problem with the switch or related parts if it receives more than 1 position signal simultaneously. The ECM will illuminate the MIL and store the DTC.
WIRING DIAGRAM


INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the tester, read the Data List.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Neutral Position SW Signal
PNP switch status/
ON or OFF
- Shift lever in P or N: ON
- Shift lever not in P or N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (P Range)
PNP switch status/
ON or OFF
- Shift lever in P: ON
- Shift lever not in P: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (R Range)
PNP switch status/
ON or OFF
- Shift lever in R: ON
- Shift lever not in R: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (2 Range)
PNP switch status/
ON or OFF
- Shift lever in 2: ON
- Shift lever not in 2: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (L Range)
PNP switch status/
ON or OFF
- Shift lever in L: ON
- Shift lever not in L: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (N Range)
PNP switch status/
ON or OFF
- Shift lever in N: ON
- Shift lever not in N: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (D Range)
PNP switch status/
ON or OFF
- Shift lever in D: ON
- Shift lever not in D: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
Shift SW Status (3 Range)
PNP switch status/
ON or OFF
- Shift lever in 3: ON
- Shift lever not in 3: OFF
When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the PNP switch or shift cable may be incorrect.
- Shift lever in P or N: ON
| 1. CHECK PARK/NEUTRAL POSITION SWITCH ASSEMBLY (POWER SOURCE) |
Disconnect the C40 park/neutral position switch connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C40-2 (RB) - Body ground
Ignition switch ON
11 to 14 V
C40-2 (RB) - Body ground
Ignition switch off
Below 1 V
Text in Illustration *a
Front view of wire harness connector
(to Park/Neutral Position Switch)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (NSW TERMINAL VOLTAGE) |
Disconnect the C40 park/neutral position switch connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C40-4 (B) - Body ground
Ignition switch ON
11 to 14 V
C40-4 (B) - Body ground
Ignition switch off
Below 1 V
Text in Illustration *a
Front view of wire harness connector
(to Park/Neutral Position Switch)
|
|
||||
| OK | |
| 3. INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Disconnect the C40 park/neutral position switch connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
- 2 (RB) - 6 (PL)
- 4 (B) - 5 (L)
Shift lever in P
Below 1 Ω
2 (RB) - 1 (RL)
Shift lever in R
Below 1 Ω
- 2 (RB) - 9 (NL)
- 4 (B) - 5 (L)
Shift lever in N
Below 1 Ω
2 (RB) - 7 (DL)
Shift lever in D or 3
Below 1 Ω
2 (RB) - 3 (2L)
Shift lever in 2
Below 1 Ω
2 (RB) - 8 (LL)
Shift lever in L
Below 1 Ω
- 2 (RB) - 6 (PL)
- 4 (B) - 5 (L)
Shift lever not in P
10 kΩ or higher
2 (RB) - 1 (RL)
Shift lever not in R
10 kΩ or higher
- 2 (RB) - 9 (NL)
- 4 (B) - 5 (L)
Shift lever not in N
10 kΩ or higher
2 (RB) - 7 (DL)
Shift lever not in D or 3
10 kΩ or higher
2 (RB) - 3 (2L)
Shift lever not in 2
10 kΩ or higher
2 (RB) - 8 (LL)
Shift lever not in L
10 kΩ or higher
- 2 (RB) - 6 (PL)
Text in Illustration *a
Component without harness connected
(Park/Neutral Position Switch)
|
|
||||
| OK | |
| 4. INSPECT SHIFT LOCK CONTROL ECU |
Disconnect the G45 shift lock control ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 (AT3) - 9 (NSSD)
Shift lever in 3
Below 1 Ω
3 (AT3) - 9 (NSSD)
Shift lever in D
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Shift Lock Control ECU)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - SHIFT LOCK CONTROL ECU) |
Disconnect the G45 shift lock control ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G45-9 (NSSD) - Body ground
- Ignition switch ON
- Shift lever in D or 3
11 to 14 V
G45-9 (NSSD) - Body ground
- Ignition switch off
- Shift lever not in D or 3
Below 1 V
- Ignition switch ON
Text in Illustration *a
Front view of wire harness connector
(to Shift Lock Control ECU)
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH, SHIFT LOCK CONTROL ECU - ECM) |
Disconnect the C63 and G60 ECM connectors.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
C63-16 (P) - Body ground
- Ignition switch ON
- Shift lever in P
11 to 14 V
C63-17 (R) - Body ground
- Ignition switch ON
- Shift lever in R
11 to 14 V*
C63-11 (N) - Body ground
- Ignition switch ON
- Shift lever in N
11 to 14 V
G60-9 (D) - Body ground
- Ignition switch ON
- Shift lever in D
11 to 14 V
G60-23 (3) - Body ground
- Ignition switch ON
- Shift lever in 3
11 to 14 V
C63-15 (2) - Body ground
- Ignition switch ON
- Shift lever in 2
11 to 14 V
C63-25 (L) - Body ground
- Ignition switch ON
- Shift lever in L
11 to 14 V
C63-16 (P) - Body ground
- Ignition switch ON
- Shift lever not in P
Below 1 V
C63-17 (R) - Body ground
- Ignition switch ON
- Shift lever not in R
Below 1 V
C63-11 (N) - Body ground
- Ignition switch ON
- Shift lever not in N
Below 1 V
G60-9 (D) - Body ground
- Ignition switch ON
- Shift lever not in D
Below 1 V
G60-23 (3) - Body ground
- Ignition switch ON
- Shift lever not in 3
Below 1 V
C63-15 (2) - Body ground
- Ignition switch ON
- Shift lever not in 2
Below 1 V
C63-25 (L) - Body ground
- Ignition switch ON
- Shift lever not in L
Below 1 V
- Ignition switch ON
Text in Illustration *a
Rear view of wire harness connector
(to ECM)
- HINT:
- *: The voltage will drop slightly due to the illumination of the back-up light.
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
Disconnect the C40 park/neutral position switch connector.
Disconnect the G60 ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C40-4 (B) - G60-24 (NSW)
Always
Below 1 Ω
C40-4 (B) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
