2013-2015 Land Cruiser Prado · Service Manual Drivetrain

P0748 Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1)

Diagnostic trouble codes · Vehicles built from Aug 2014

Versions by build date: Aug 2013 – Jul 2014 from Aug 2014

DESCRIPTION

Shifting from 1st to 5th is performed in combination with the ON and OFF operation of the shift solenoid valves SL1, SL2, S1, S2 and SR, which are controlled by the ECM. If an open or short circuit occurs in one of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Click here).
DTC Code
DTC Detection Condition
Trouble Area
P0748
The ECM checks for an open or short in the shift solenoid valve SL1 circuit while driving and shifting between 4th and 5th gear (1-trip detection logic).
Output signal duty equals 100%.

HINT:
SL1 output signal duty is less than 100% under normal conditions.

  1. Open or short in shift solenoid valve SL1 circuit
  2. Shift solenoid valve SL1
  3. ECM

MONITOR DESCRIPTION

This DTC indicates an open or short in the shift solenoid valve SL1 circuit. The ECM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the ECM detects the problem, illuminates the MIL and stores the DTC. Then the ECM performs the fail-safe function and turns the other normal shift solenoid valves ON/OFF. In case of an open or short circuit, the ECM stops sending current to the circuit.
While driving and shifting between 4th and 5th gears, if the ECM detects an open or short in the shift solenoid valve SL1 circuit, the ECM determines there is a malfunction (Click here).

WIRING DIAGRAM

C161203E91

INSPECTION PROCEDURE


HINT:
The shift solenoid valve SL1 is turned ON/OFF normally when the shift lever is in D.
ECM gear shift command
1st
2nd
3rd
4th
5th
Shift solenoid valve SL1
OFF
OFF
OFF
OFF
ON


1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL1)

  1. C214326E02
    Disconnect the C30 transmission wire connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    12 (SL1+) - 4 (SL1-)
    20°C (68°F)
    5.0 to 5.6 Ω
    12 (SL1+) - Body ground
    Always
    10 kΩ or higher
    4 (SL1-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Transmission Wire)



NG
Go to step 3
OK


2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)

  1. C214337E13
    Disconnect the C36 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C36-33 (SL1+) - C36-32 (SL1-)
    20°C (68°F)
    5.0 to 5.6 Ω
    C36-33 (SL1+) - Body ground
    Always
    10 kΩ or higher
    C36-32 (SL1-) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

3. INSPECT SHIFT SOLENOID VALVE SL1

  1. C197715E09
    Remove shift solenoid valve SL1.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    5.0 to 5.6 Ω

  1. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

    OK:
    Measurement Condition
    Specified Condition
    1. Battery positive (+) with a 21 W bulb → Terminal 1
    2. Battery negative (-) → Terminal 2
    Valve moves and makes operating noise

Text in Illustration 
*a
Component without harness connected
(Shift Solenoid Valve SL1)


NG
REPLACE SHIFT SOLENOID VALVE SL1 (Click here)
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)


← P0748 Pressure Control Solenoid "A" Electrical (Shift Solenoid Valve SL1) (Aug 2013 – Jul 2014)P0751 Shift Solenoid "A" Performance (Shift Solenoid Valve S1) (Aug 2013 – Jul 2014) →