P0778 Pressure Control Solenoid "B" Electrical (Shift Solenoid Valve SL2)
Diagnostic trouble codes · Vehicles built Aug 2013 – Jul 2014
Versions by build date: Aug 2013 – Jul 2014 from Aug 2014
DESCRIPTION
Shifting from 1st to 5th is performed in combination with the ON and OFF operation of shift solenoid valves SL1, SL2, S1, S2 and SR, which are controlled by the TCM. If an open or short circuit occurs in one of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated smoothly (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0778 |
The TCM checks for an open or short in the shift solenoid valve SL2 circuit while driving and shifting gears (1-trip detection logic). Output signal duty ratio equals 100%.
|
|
MONITOR DESCRIPTION
This DTC indicates an open or short in the shift solenoid valve SL2 circuit. The TCM commands gear shifts by turning the shift solenoid valves ON/OFF. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem, illuminates the MIL and stores the DTC. Then the TCM performs the fail-safe function and turns the other normal shift solenoid valves ON/OFF. In the case of an open or short circuit, the TCM stops sending current to the circuit.While driving and shifting gears, if the TCM detects an open or short in the shift solenoid valve SL2 circuit, the TCM determines there is a malfunction (Click here).
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Shift solenoid valve SL2 is turned ON/OFF normally when the shift lever is in D.
TCM gear shift command
1st
2nd
3rd
4th
5th
Shift solenoid valve SL2
ON
ON
ON
ON
OFF
| 1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL2) |
Disconnect the C30 transmission wire connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
11 (SL2+) - 3 (SL2-)
20°C (68°F)
5.0 to 5.6 Ω
11 (SL2+) - Body ground
20°C (68°F)
10 kΩ or higher
3 (SL2-) - Body ground
20°C (68°F)
10 kΩ or higher
Text in Illustration *a
Component without harness connected
(Transmission Wire)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM) |
Disconnect the G69 TCM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
G69-7 (SL2+) - G69-6 (SL2-)
20°C (68°F)
5.0 to 5.6 Ω
G69-7 (SL2+) - Body ground
20°C (68°F)
10 kΩ or higher
G69-6 (SL2-) - Body ground
20°C (68°F)
10 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to TCM)
|
|
||||
| OK | ||
| ||
| 3. INSPECT SHIFT SOLENOID VALVE SL2 |
![]() ![]() |
Remove shift solenoid valve SL2.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
5.0 to 5.6 Ω
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
- OK:
Measurement Condition
Specified Condition
- Battery positive (+) with a 21 W bulb → Terminal 1
- Battery negative (-) → Terminal 2
Valve moves and makes an operating noise
- Battery positive (+) with a 21 W bulb → Terminal 1
| *a |
Component without harness connected (Shift Solenoid Valve SL2) |
|
|
||||
| OK | ||
| ||

