2013-2015 Land Cruiser Prado · Service Manual Steering

REASSEMBLY

Removal / installation · Vehicles built from Aug 2013

NOTICE:
When installing parts, coat the parts indicated by arrows with power steering fluid (Click here).


1. INSTALL VANE PUMP HOUSING OIL SEAL
  1. Coat the lip of a new vane pump housing oil seal with MP grease.

  1. C101980E04
    Using SST and a press, install the vane pump housing oil seal to the vane pump front housing.
    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07150)

    NOTICE:
    Make sure that the vane pump housing oil seal is installed so that it is facing in the correct direction as shown in the illustration.


2. INSTALL VANE PUMP SHAFT BEARING

  1. C101975
    Using a snap ring expander, install the vane pump shaft snap ring to the vane pump shaft.

  1. Wrap the serration of the vane pump shaft with protective tape.

  1. C101981E04
    Using a press, install the vane pump shaft bearing to the vane pump shaft.

    NOTICE:
    1. Do not damage the vane pump shaft bearing.
    2. Make sure that the vane pump shaft bearing inner race sits on the V-blocks.

    Text in Illustration 
    *1
    Protective Tape
    *2
    Inner Race


3. INSTALL VANE PUMP GEAR

  1. C102432E02
    Using SST and a press, install the vane pump gear to the vane pump shaft.
    SST
    09950-60010   (09951-00250)
    Text in Illustration 
    *1
    Press

    HINT:
    Press in the vane pump shaft until the end faces of the shaft and vane pump gear become aligned.

  1. C102433E02
    Using SST and a press, install the vane pump shaft to the vane pump front housing.
    SST
    09950-60010   (09951-00250)

    HINT:
    Press in the vane pump shaft until the snap ring groove of the vane pump front housing can be seen.

  1. Install the vane pump housing snap ring No. 1 to the vane pump front housing.


4. INSTALL VANE PUMP FRONT SIDE PLATE

  1. C101970
    Coat a new O-ring with power steering fluid and install it to the vane pump front housing.

  1. C101969
    Coat a new O-ring with power steering fluid and install it to the vane pump front side plate.

  1. C101385
    Align the notch of the vane pump front side plate with that of the vane pump front housing and install the vane pump front side plate.

    NOTICE:
    Make sure that the vane pump front side plate is installed so that it is facing in the correct direction as shown in the illustration.


5. INSTALL VANE PUMP CAM RING

  1. C101386E02
    Align the notch of the vane pump cam ring with that of the vane pump front side plate and install the vane pump cam ring with the inscribed mark facing upward.
    Text in Illustration 
    *a
    Inscribed Mark

    NOTICE:
    Make sure that the cam ring is installed so that it is facing in the correct direction.


6. INSTALL VANE PUMP ROTOR
  1. Coat the vane pump rotor with power steering fluid.

  1. Install the vane pump rotor.

    HINT:
    The vane pump rotor has no specific direction.

  1. Coat all 10 vane pump plates with power steering fluid.

  1. D030335E14
    Install the vane pump plates with the round end facing outward.
    Text in Illustration 
    *a
    Round End
    *b
    Outward
    *c
    Inward

    NOTICE:
    Make sure that the vane pump plates are installed so that they are facing in the correct direction.


7. INSTALL VANE PUMP REAR HOUSING
  1. Coat a new O-ring with power steering fluid and install it to the vane pump rear housing.

  1. C101387
    Align the straight pin of the vane pump rear housing with the notches of the vane pump cam ring, vane pump front side plate and the vane pump front housing, and install vane pump rear housing with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }


8. SECURE VANE PUMP ASSEMBLY

  1. C215469E01
    Using SST, secure the vane pump assembly in a vise.
    SST
    09630-00014   (09631-00132)


9. INSPECT TOTAL PRELOAD
  1. Check that the pump rotates smoothly without abnormal noise.

  1. Temporarily install a service bolt.

    Recommended Service Bolt:
    Item
    Specified Condition
    Thread diameter
    10 mm (0.394 in.)
    Thread pitch
    1.25 mm (0.0492 in.)
    Bolt length
    50 mm (1.97 in.)

  1. G021500
    Using a torque wrench, check the rotating torque.

    Standard Rotating torque:
    0.3 N*m (3 kgf*cm, 2 in.*lbf) or less

    If the rotating torque is not as specified, check the installation condition of each part.


10. INSTALL SUCTION PORT UNION
  1. Coat a new O-ring with power steering fluid and install it to the suction port union.

  1. Install the suction port union to the vane pump front housing with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

← INSPECTION (from Aug 2013)INSTALLATION (from Aug 2013) →